cmOtpProgramResult
BRCM-CM-FACTORY-MIB ·
.1.3.6.1.4.1.4413.2.99.1.1.2.2.6.3
Object
scalar
Enumeration
Indicates the result of an attempt to program the OTP. Note that this
value does not persist across a reboot, but it will provide the result
of an attempt to program the OTP until the device is rebooted.
notAttempted(-1): no attempt has been made to program the OTP since the
last reboot.
success(0): programming was successful.
failedAlreadyProgrammed(1): the part has already been programmed.
failedProgrammingNotSupported(2): OTP programming is not supported on
this platform.
failedHardwareFailure(3): internal h/w failure. In this case, the
chip should be discarded, since some of the bits may have been
programmed and others might have failed.
Context
- MIB
- BRCM-CM-FACTORY-MIB
- OID
.1.3.6.1.4.1.4413.2.99.1.1.2.2.6.3- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- cmFactoryOtp
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
-1 | notAttempted |
0 | success |
1 | failedAlreadyProgrammed |
2 | failedProgrammingNotSupported |
3 | failedHardwareFailure |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cmOtpIsProgrammed Indicates if the OTP section of this chip has been programmed. Note
that if this object returns true(1), all objects in this group will
be read-only and any attempt to write them… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.1 |
| cmOtpConsoleDisabled If set to true(1), disables the serial console port in hardware. If
set to false(2), serial console will remain enabled.
Setting cmOtpSecurityLevel to fullSecurity(2)… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.10 |
| cmOtpSpiSlaveDisabled If set to true(1), disables the SPI slave in hardware. If
set to false(2), the SPI slave will remain enabled.
Setting cmOtpSecurityLevel to fullSecurity(2) will cause… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.11 |
| cmOtpMpiAccessControl Indicates the value of the MPI access control setting.
The effect of setting cmOtpSecurityLevel on the value of this object
is platform-dependant. | scalar | Enumeration | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.12 |
| cmOtpBootRomEnabled If set to true(1), the part will boot only from ROM. If
set to false(2), the part will boot from a bootloader in flash.
Setting cmOtpSecurityLevel to fullSecurity(2) … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.13 |
| cmOtpRamScramblerEnabled Enables or disables the RAM scrambler.
Setting cmOtpSecurityLevel to fullSecurity(2) will cause the value of
this object to be set to true(1). Setting cmOtpSecurityLe… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.14 |
| cmOtpProgramNow If set to true(1), initiates programming of the OTP. Setting to
false(2) has no effect. Always returns false(2) when read.
Note that setting this object to true(1) w… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.2 |
| cmOtpRawBitsSize Indicates the size of the OTP region in bits. | scalar | Unsigned32 | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.4 |
| cmOtpRawBits Allows reading or writing the OTP region as a raw hex value.
When reading, note that only the right-most bits are valid. The
number of valid bits is returned by otp… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.5 |
| cmOtpCustomerDefinedBitsSize Indicates the size of the customer defined region in bits. | scalar | Unsigned32 | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.6 |
| cmOtpCustomerDefinedBits Allows reading or writing the customer defined region as a raw hex
value.
When reading, note that only the right-most bits are valid. The
number of valid bits is r… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.7 |
| cmOtpSecurityLevel Reports and controls the current security level for the cumulative
set of supported OTP features for this device. This provides a
platform-independent mechanism to set all suppo… | scalar | Enumeration | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.8 |
| cmOtpJtagDisabled If set to true(1), disables JTAG in hardware. If set to false(2),
JTAG will remain enabled.
Setting cmOtpSecurityLevel to fullSecurity(2) will cause the value of
t… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.99.1.1.2.2.6.9 |