cmFactOperMode

BRCM-CM-FACTORY-MIB · .1.3.6.1.4.1.4413.2.99.1.1.2.2.1.1
MIB view Table view

Object

scalar r/w Enumeration 
Reflects and controls the operational state of the device.  If
set to docsis(1), the CM will operate in the usual DOCSIS fashion.
If set to diagnostic(2), the CM will not begin scanning at boot
time, rather it will simply initialize the diagnostic IP stack
with the provisioned IP address and await instructions.  If this
object is changed after boot time from docsis(1) to diagnostic(2),
the CM will abort any DOCSIS operations which have begun and return
to the diagnostic state immediately.  If changed from diagnostic(2)
to docsis(1), the CM will begin DOCSIS operations to the best of its
ability given the current state.  Note that certain diagnostic
operations may interfere with normal DOCSIS operation until after
the next boot sequence.

Context

MIB
BRCM-CM-FACTORY-MIB
OID
.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.1
Type
scalar
Access
readwrite
Status
current
Parent
cmFactoryBase
Siblings
13

Syntax

Enumeration

Values & Constraints

Enumerated Values
1docsis
2diagnostic

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cmFactHighOutputPAEnable
Enables or disables the support of high-output power amp mode on the CM.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.10
cmFactChannelBondingEnable
Enables or disables the support of channel bonding. Note that this setting will only have any effect if the hardware and firmware support channel bonding.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.11
cmFactEnabledTuners
Specifies the number of tuners which will be advertised to the CMTS in the CM's modem capabilities message. By advertising fewer tuners than the design actually supports, power c…
scalarInteger32.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.12
cmFactAnnex
Specifies the annex mode which will be used. This setting affects downstream tuning parameters including frequency list and phy level operation.
scalarEnumeration.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.13
cmFactExtendedUsTxPowerCapability
Specifies the maximum extended upstream transmit power of which this device is capable. A value of zero indicates that the device has no extended upstream power capability. Th…
scalarquarter dBmV Integer32.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.14
cmFactSwBcmVersion
The Broadcom internal software version identifier of this image. This is generally not the same as docsDevSwVersion.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.2
cmFactSwDateTime
The date and time that this image was built.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.3
cmFactSwBuiltBy
The user ID of the individual who built this image.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.4
cmFactSwFeatures
A list of features supported by this image.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.5
cmFactAckCelEnable
Enables or disables Broadcom's Patent Pending AckCel technology for the CM Upstream interface. Changes to this value take effect the next time the CM registers with a CMTS.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.6
cmFactNonstdUpstreamEnable
Enables or disables the support of non-standard upstream configurations. If enabled, the s/w will accept and use UCDs that contain proprietary non-standard modes of operation t…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.7
cmFactPowerSaveModeEnable
Enables or disables power save mode. With power save mode enabled, various measures will be taken to reduce power consumption. Power save mode is primarily useful for battery p…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.8
cmFactOptimized3420FreqMapEnable
Enables or disables the use of the optimized frequency map for devices which use the 3420 tuner. Note that this object has no meaning if the device uses a tuner other than the 34…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.2.2.1.9