potsIfAdminState
BINTEC-POTS-MIB ·
.0.14.1.1.1.5
Object
column
r/w
Enumeration
This variable allows for taking an POTS interface out of/in
service w/o having to touch the configuration.
Besides, it is possible to initiate a reconfiguration for that
interface in case a mismatch in configuration parameters
(hardware vs. software) was detected.
Inconsistencies with the need of reconfiguration is a differing
potsIfMode (fxo/fxs).
In case of mismatch, contents of this variable might be
wrong and this circumstance is reflected in variable
potsIfOperState. State reconfig may then be used in order to
cause an update of these variable as appropriate which ...
- will be signalled to higher protocol layers, and
- can result in extensive reconfiguration steps
The latter may also cover clean-ups undoable by system so this
decision is left to the user.
Default value is down.
Context
- MIB
- BINTEC-POTS-MIB
- OID
.0.14.1.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- potsIfEntry
- Table
- potsIfTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | down |
2 | up |
3 | reconfig |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| potsSlot Identification number of the used slot. | column | Integer32 | .0.14.1.1.1.1 |
| potsIfCoeffIndex Selection of the coefficient set provided
by the FXS or FXO line driver. This allows
to use specific settings with e.g. resistive or
complex line impedances. Supported values a… | column | SNMPv2-SMIInteger32 | .0.14.1.1.1.10 |
| potsIfTxGain Amplification or attenuation (negative gain)
of outgoing audio in dB. | column | dB Integer32 | .0.14.1.1.1.11 |
| potsIfRxGain Amplification or attenuation (negative gain)
of incoming audio in dB. | column | dB Integer32 | .0.14.1.1.1.12 |
| potsIfDialInTimeout Limit for time interval between two consecutive
dialling digits. | column | s Integer32 | .0.14.1.1.1.13 |
| potsUnit Identification number of the used unit. | column | Integer32 | .0.14.1.1.1.2 |
| potsType The type of the connected device on socket a.
Possible values are:
- any(1), (multifunctional)
- fax(2),
- telephony(3),
… | column | Enumeration | .0.14.1.1.1.3 |
| potsIfMode Type of outlet. | column | Enumeration | .0.14.1.1.1.4 |
| potsIfOperState The operational state of an interface is indicated via this
variable.
Possible values are:
- down(1),
- running(2),
- fail(3),
- not-connected(4),
… | column | Enumeration | .0.14.1.1.1.6 |
| potsIfIndex Reference to the FXS or FXO table. | column | PotsIfIndex | .0.14.1.1.1.7 |
| potsIfTtxLevel Teletax (metering pulse) level:
for FXS lines: output level
for FXO lines: minimum level | column | Integer32 | .0.14.1.1.1.8 |
| potsIfTtxFreq Teletax (metering pulse) frequency:
1: no teletax output/reception
3: 12 kHz
4: 16 kHz | column | Enumeration | .0.14.1.1.1.9 |