ipExtIfOspfMetric

BINTEC-IPEXT-MIB · .0.3.1.16

Object

column r/w Enumeration

Configure the metric calculation of OSPF interfaces. If set
to auto the metric is calculated based on ifSpeed. If set
to fixed the metric is taken from the ospfIfMetricTable.
Additionaly the metric adjustment for dialup interfaces 
can be configured. If set to auto-adjust or fixed-adjust
the basic metric value is reduced if the operational status
of the dialup interface is up.

Context

MIB: BINTEC-IPEXT-MIB
OID: .0.3.1.16
Type: column
Access: readwrite
Status: current
Parent: ipExtIfEntry
Table: ipExtIfTable
Siblings: 37

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
ipExtIfIndex Unique interface index	column	Integer32	`.0.3.1.1`
ipExtIfNatOutXlat This object can be used to switch the outgoing address translation off. Then, all addresses are passed instead of being translated. The session mechanism remains active and implem…	column	Enumeration	`.0.3.1.10`
ipExtIfAccounting Switch for accounting on the specified interface. An IP packet is being accounted, when this object is set to on for either the source or the destination interface.	column	Enumeration	`.0.3.1.11`
ipExtIfTcpSpoofing Switch for TCP spoofing on this interface. TCP keepalive polls are answered by the BRICK to prevent unnecessary ISDN connections. Set this object to on for ISDN dialup interfaces.	column	Enumeration	`.0.3.1.12`
ipExtIfAccessAction This object describes the action, that is done, when a packet received from the interface has been filtered out. When set to ignore, no action takes place. When set to refuse, an …	column	Enumeration	`.0.3.1.13`
ipExtIfAccessReport This object specifies, how a packed filtered by accesslists should be logged. When set to none, no logging takes place. When set to info, protocol, ip-addresses and portnumbers ar…	column	Enumeration	`.0.3.1.14`
ipExtIfOspf Configure the OSPF status of this interface. Routing information about routes on passive and active interfaces is propagated on active interfaces. Only active interfaces run the…	column	Enumeration	`.0.3.1.15`
ipExtIfTcpCksum Enable or disable the TCP checksum check for local packets received on the corresponding interface. Disabling the check may improve performance for some local applications (i.e. r…	column	Enumeration	`.0.3.1.17`
ipExtIfBackRtVerify This object activates an additional check for incoming packets. If set to on, incoming packets are only accepted if return packets sent back to their source IP address would be s…	column	Enumeration	`.0.3.1.18`
ipExtIfRuleIndex This object defines the index of the first access rule that is applied for incoming packets. If set to 0 or if there is no access rule with this index no access rules are appl…	column	Integer32	`.0.3.1.19`
ipExtIfAuthentication This object defines the authentication scheme used for incoming packets.	column	Enumeration	`.0.3.1.20`
ipExtIfAuthMode This object defines the authentication mode. If set to strict each source IP address must be authenticated. If set to loose all source IP addresses are allowed if at least one IP…	column	Enumeration	`.0.3.1.21`
ipExtIfAuthLifeTime This object defines the time in seconds a successful authentication is valid since the IP partner was authenticated.	column	seconds Integer32	`.0.3.1.22`
ipExtIfAuthKeepalive This object defines the period between short authentications that are invisible to the user	column	seconds Integer32	`.0.3.1.23`
ipExtIfRouteAnnounce This object defines the condition when routes on this interface are propagated by routing protocols. If set to up-only routes are only propagated if the operational status of the …	column	Enumeration	`.0.3.1.24`
ipExtIfIpFragmentation This object defines different modes used for fragmentation of IP datagrams greater than the MTU of the destination interface. If set to enabled (1) each IP datagram will be splitt…	column	Enumeration	`.0.3.1.25`
ipExtIfRerouting This object enables or disables rerouting on this interface. The default value is enabled. If set to disabled, then only the better one route from two or more possible routes is …	column	Enumeration	`.0.3.1.26`
ipExtIfBodRuleIndex This object defines the index of the first rule used for Bandwidth on Demand (BOD) that is applied for incoming and/or outgoing traffic. If set to 0 or if there is no entry in the…	column	Integer32	`.0.3.1.27`
ipExtIfQosRuleIndex This object defines the index of the first rule used for Qos (Qualtiy of Service) rules applied for IP traffic. If set to 0 or if there is no entry in the ipQoSTable with this ind…	column	Integer32	`.0.3.1.28`
ipExtIfIpsecAccounting This object determines, whether packets which are en- or decapsulated by IPSec should be accounted with encapsulation header(ipsec) or without the encapsulation header (clear), …	column	Enumeration	`.0.3.1.29`
ipExtIfRipSend specifies which versions of RIP messages are sent to that interface. Usually RIP messages are sent as broadcast, except this object is set to ripV2mcast. In this case RIP V2 messa…	column	Enumeration	`.0.3.1.3`
ipExtIfMulticast Enable that multicast frames are accepted from that interface.	column	Enumeration	`.0.3.1.30`
ipExtIfNatSilentDeny This object specifies - if NAT is enabled (see ipExtIfNat) - whether incoming IP packets not passed by the NAT barrier should answered with an ICMP Host Unreachable or TCP RST mes…	column	Enumeration	`.0.3.1.31`
ipExtIfNatPPTPXlat This object specifies - if NAT is enabled (see ipExtIfNat) - whether PPTP (point to point protocol) connections are translated. This is needed if there are more than one PPTP clie…	column	Enumeration	`.0.3.1.33`
ipExtIfTcpMssClamping This object specifies whether TCP MSS clamping is enabled on the interface. -1 disables clamping, 0 clamps the MSS depending on the interface MTU. A value > 0 will be used as clam…	column	bytes Integer32	`.0.3.1.34`
ipExtIfNbdgmRelayAddress This object contains the destination IP address to which Netbios Datagram request are forwarded by the router.	column	RFC1155-SMIIpAddress	`.0.3.1.35`
ipExtIfNatMaxSessions This object limits the maximum number of NAT sessions on a interface.	column	Integer32	`.0.3.1.36`
ipExtIfAllowedPeers If this object is set to 'dhcpclients', the router refuses to exchange data with hosts which are not DHCP clients on this interface. If this object is set to 'all', the router a…	column	Enumeration	`.0.3.1.37`
ipExtIfNatFlush If this object in enabled NAT-Flushing is done else not. NAT-Flushing means that the NAT Entries for this interface will be deleted in the case of an OperStatus change to down or…	column	Enumeration	`.0.3.1.38`
ipExtIfHttpRedirect If not set to 'disabled' all HTTP requests on this interface will be directed either to the local HTTP daemon or HTTP proxy.	column	Enumeration	`.0.3.1.39`
ipExtIfRipReceive specifies which versions of RIP messages are accepted from that interface. RIP V2 messages are received regardless if they are sent as broadcast or multicast.	column	Enumeration	`.0.3.1.4`
ipExtIfWolRuleIndex This object defines the index of the first rule used for Wake-On-LAN (WOL) that is applied for incoming and/or outgoing traffic. If set to 0 or if there is no entry in the ipWolRu…	column	Integer32	`.0.3.1.40`
ipExtIfProxyArp Switch for Proxy ARP on this interface.	column	Enumeration	`.0.3.1.5`
ipExtIfNat This object can be used to switch NAT on and off for a specific interface.	column	Enumeration	`.0.3.1.6`
ipExtIfNatRmvFin This object specifies, whether entries in the IpNatTable shall be removed, when TCP-FINS have been received and acknowledged in both directions, a TCP-RST has been received or a I…	column	Enumeration	`.0.3.1.7`
ipExtIfNatTcpTimeout TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds.	column	seconds Integer32	`.0.3.1.8`
ipExtIfNatOtherTimeout Non-TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds.	column	seconds Integer32	`.0.3.1.9`