ethPhyPortCapabilities
BIANCA-ETH-PHY-MIB ·
.0.1.1.9
Object
column
Bits
This bitfield describes what modes the port supports: half-10 : 10Mbit/s half duplex full-10 : 10Mbit/s full duplex half-100 : 100Mbit/s half duplex full-100 : 100Mbit/s full duplex half-1000 : 1000Mbit/s half duplex full-1000 : 1000Mbit/s full duplex autoneg : Autonegotiation supported .
Context
- MIB
- BIANCA-ETH-PHY-MIB
- OID
.0.1.1.9- Type
- column
- Access
- readonly
- Status
- current
- Parent
- ethPhyEntry
- Table
- ethPhyTable
- Siblings
- 12
Syntax
Bits
Values & Constraints
Enumerated Values
0 | half-10 |
1 | full-10 |
2 | half-100 |
3 | full-100 |
4 | half-1000 |
5 | full-1000 |
6 | autoneg |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ethPhyPortIndex The unique ethernet PHY interface index. | column | SNMPv2-SMIInteger32 | .0.1.1.1 |
| ethPhyPortMode The initial mode of the ethernet PHY or switch port:
disable(1) -- disconnect from physical line
auto(2) -- use default autonegotiation
auto-10… | column | Enumeration | .0.1.1.10 |
| ethPhyEthAssignedIfIndex obsolete The Ethernet interface index the PHY or switch port
is connected/assigned to.
The system will create interfaces as needed, but there
can't be more ethernet interfaces than switch … | column | SNMPv2-SMIInteger32 | .0.1.1.12 |
| ethPhyExtendedDistance If the PHY supports different receive thresholds depending
on the cable length (long-cable > 100 m) and speed (10BaseT)
it could be configured by this variable. | column | Enumeration | .0.1.1.13 |
| ethPhyPortGroup The port group this phy is member of. | column | Integer32 | .0.1.1.18 |
| ethPhyChipVendor The vendor name or identifier of the PHY or switch
detected during hardware scan. | column | OctetString | .0.1.1.2 |
| ethPhyPortDescr This object is available to the user for
specifying a user-friendly name or tag. | column | SNMPv2-TCDisplayString | .0.1.1.21 |
| ethPhyPortFlowControl If the PHY supports flow control according to IEEE 802.3x
flow control can be enabled on that port by setting variable
to value 'auto'. This will cause 802.3x to be advertised via… | column | Enumeration | .0.1.1.22 |
| ethPhyPortFlowControlStatus This variable indicates whether flow control according to IEEE
802.3x is currently active on that port.
Possible values are ...
disabled(1) and
enabled(2) | column | Enumeration | .0.1.1.23 |
| ethPhyChipModel The chip modell/revision of the PHY or switch
detected during hardware scan. | column | OctetString | .0.1.1.3 |
| ethPhyPortLinkStatus This variable indicates link status and autonegotiation
results:
down(1) -- link down or autonegotiation failed
auto-neg-failed(2) -- autonegotiation … | column | Enumeration | .0.1.1.6 |
| ethPhyPortMdixStatus This variable indicates the cables MDIX status
if the link is established. | column | Enumeration | .0.1.1.7 |