pppExtIfDialinL1Protocol

BIANCA-BRICK-PPP-MIB · .1.3.6.1.4.1.272.4.3.9.1.27
MIB view Table view

Object

column mandatory r/w Enumeration 
This variable determines the permitted layer 1 protocol
for incoming calls. If set to all(31) there is no specific
restriction. In all other cases incoming calls are either
rejected (when identified via CLID) or terminated after
identification via PPP authentication (inband authentication)
if the used layer 1 protocol doesn't match. Note that this
check will be also performed for any initial call used to
initiate a callback.

Context

MIB
BIANCA-BRICK-PPP-MIB
OID
.1.3.6.1.4.1.272.4.3.9.1.27
Type
column
Access
readwrite
Status
mandatory
Parent
pppExtIfEntry
Table
pppExtIfTable
Siblings
29

Syntax

Enumeration

Values & Constraints

Enumerated Values
1data-64k
2data-56k
3modem
4dovb
5v110-1200
6v110-2400
7v110-4800
8v110-9600
9v110-14400
10v110-19200
11v110-38400
12modem-profile-1
13modem-profile-2
14modem-profile-3
15modem-profile-4
16modem-profile-5
17modem-profile-6
18modem-profile-7
19modem-profile-8
20pptp-pns
21pppoe
22pppx25
23pptp-pac
24l2tp-lns
25l2tp-lac
26dovb-64k
31all

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
pppExtIfIndex mandatory
Correlating PPP interface index.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.1
pppExtIfEncKeyNegotiation mandatory
This variable defines the specification of shared secrets (encryption keys) between the sender and receiver of encrypted data. If set to static (1), the keys specified in 'pppExtI…
columnEnumeration.1.3.6.1.4.1.272.4.3.9.1.10
pppExtIfEncTxKey mandatory
Static (encryption) key used for transmission of encrypted data via PPP. It's size depends on the used encryption algorithm and the corresponding key length, e.g. 'des_56' or 'bl…
columnOctetString.1.3.6.1.4.1.272.4.3.9.1.11
pppExtIfEncRxKey mandatory
Static (decryption) key used for decryption of encrypted data received on PPP connections. It's size depends on the used encryption algorithm and the corresponding key length, e.g…
columnOctetString.1.3.6.1.4.1.272.4.3.9.1.12
pppExtIfGearUpThreshold mandatory
Gear up threshold for invoking current bandwidth. The measured throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) is compared with this value once…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.13
pppExtIfGearDownThreshold mandatory
Gear down threshold for decreasing current bandwidth. The expected throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) after dropping a B-channel i…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.14
pppExtIfAodiDChanQlen mandatory
Upper threshold for the amount of data (in octets) waiting to be sent across the 9.6Kbit/sec D-channel. If exceeded, additional bandwidth will be invoked at once.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.15
pppExtIfAodiGearDownTxRate mandatory
Lower threshold for the amount of data in bits per second to be sent across the 64Kbit/sec B-channel. If the measured throughput becomes smaller than this value over a period of p…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.16
pppExtIfGearUpPersistance mandatory
Gear up persistence interval for invoking current bandwidth. The measured throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) is compared with the …
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.17
pppExtIfGearDownPersistance mandatory
Gear down persistence interval for decreasing current bandwidth. The measured throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) is compared with …
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.18
pppExtIfL1Speed mandatory
This object contains the interface's nominal bandwidth in bits per second. Please note that this parameter may not represent the real available transmission rate. The current pu…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.19
pppExtIfBodMode mandatory
Enables bandwidth on demand (BOD) mode for leased line and dialup interfaces when setting to bod-active (3) respectively bod-passive (4) or backup only mode for leased line connec…
columnEnumeration.1.3.6.1.4.1.272.4.3.9.1.2
pppExtIfCurrentRetryTime mandatory
Current time in seconds to wait before retrying a call when the smart retry algorithm is implemented.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.20
pppExtIfMaxRetryTime mandatory
Maximum time in seconds to wait before retrying a call when the smart retry algorithm is implemented. When set to zero this algorithm is disabled.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.21
pppExtIfMtu mandatory
Determines size of the largest datagram which can be sent on the interface, specified in octets (see ifMtu). When set to zero (default), the value of the variable ifMtu depends on…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.22
pppExtIfMru mandatory
The maximum length for the PPP information field, including padding, but not including the protocol field, is termed the Maximum Receive Unit (MRU).
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.23
pppExtIfAuthMutual mandatory
This object enables mutual PPP authentication between the peers.
columnEnumeration.1.3.6.1.4.1.272.4.3.9.1.24
pppExtIfDialProfileIndex mandatory
References the associated dial profile.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.26
pppExtIfpppoeEthIfIndex mandatory
Determines the Ethernet interface to be used for PPP over Ethernet (PPPoE) according RFC 2516. If not specified here the value in biboPPPProfilePPPoEDevIfIndex will be used as fal…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.28
pppExtIfpppoaPvcIfIndex mandatory
Determines the ATM PVC to be used for PPP over Ethernet (PPPoA) according RFC 2364 - PPPoA on demand mode. If not specified here the first ATM PVC configured for PPPoA on demand (…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.29
pppExtIfAlgorithm mandatory
The algorithm to use for weighting line utilization. Line utilization is determined by calculating the average load for each interface. When set to equal (1) all samples taken ove…
columnEnumeration.1.3.6.1.4.1.272.4.3.9.1.3
pppExtIfRadiusMarkAcct mandatory
Determines wether start or stop of RADIUS accounting should be marked (via Accounting-On/Accounting-Off) for the logical RADIUS server group specified by pppExtIfRadiusGroupId. RA…
columnEnumeration.1.3.6.1.4.1.272.4.3.9.1.30
pppExtIfRadiusGroupId mandatory
Determines the logical RADIUS server group to be addressed for sending the RADIUS Accounting-On/Accounting-Off messages. See also radiusSrvPriority.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.31
pppExtIfInterval mandatory
The time interval (in seconds) to use for sampling and calculating of the average throughput of the interface. See also: pppExtIfLoad.
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.4
pppExtIfLoad mandatory
The actual throughput (in percent) of the total bandwidth of this interface (load). This value is updated once every second and based on the amount of traffic during the last sam…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.5
pppExtIfMlpFragmentation mandatory
The multilink PPP fragmentation mode. When set to proportional (1) packets will be divided into fragments proportional to the transmission rate of each link, when set to equal (…
columnEnumeration.1.3.6.1.4.1.272.4.3.9.1.6
pppExtIfMlpFragSize mandatory
The multilink PPP fragment size. If MlpFragmentation is set to proportional (1) this value specifies the minimum size of the fragment in bytes. If MlpFragmentation is set to equal…
columnInteger32.1.3.6.1.4.1.272.4.3.9.1.7
pppExtIfPPPoEService mandatory
The PPPoE (PPP over Ethernet, RFC 2516) service name which indicates the requested service during PPPoE discovery stage. Examples of the use of the service name are to indicate an…
columnOctetString.1.3.6.1.4.1.272.4.3.9.1.8
pppExtIfPPPoEAcServer mandatory
The PPPoE (PPP over Ethernet, RFC 2516) AC-Server name which determines the access concentrator during PPPoE discovery stage.
columnOctetString.1.3.6.1.4.1.272.4.3.9.1.9