atiStkSwPortBackPressure
AtiStackSwitch9000-MIB ·
.1.3.6.1.4.1.207.8.17.2.1.1.10
Object
column
r/w
Enumeration
This object is used to enable/disable Back Pressure on the
port.
Back Pressure is disabled by default.
Context
- MIB
- AtiStackSwitch9000-MIB
- OID
.1.3.6.1.4.1.207.8.17.2.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- atiStkSwPortConfigEntry
- Table
- atiStkSwPortConfigTable
- Siblings
- 15
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | unknown |
2 | disable |
3 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| atiStkSwModuleId This object specifies the ID of a module present in the switch
stack. | column | Integer32 | .1.3.6.1.4.1.207.8.17.2.1.1.1 |
| atiStkSwPortPriority This object specifies whether packets flowing through this
port use the associated VLAN priority or override the
associated VLAN priority with either a high or a low priority.
… | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.11 |
| atiStkSwPortBroadcastProcessing This object specifies whether the received broadcast packets
should be processed or discarded.
Broadcast packets are processed by default. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.12 |
| atiStkSwPortMDIO This object is used to set the MDIO of this port for required
cable connection type. For straight-through cable set to mdi
and for cross-over cable set to mdix. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.13 |
| atiStkSwPortHOLLimit This object allows user to set the head of line blocking limit.
Note (94xx): Range upto 8191 is supported for Gigabit Ports. | column | Integer32 | .1.3.6.1.4.1.207.8.17.2.1.1.14 |
| atiStkSwPortBackPressureLimit This object is used to set the MDIO of this port for required
cable connection type. For straight-through cable set to mdi
and for cross-over cable set to mdix. This limit can be… | column | Integer32 | .1.3.6.1.4.1.207.8.17.2.1.1.15 |
| atiStkSwPortSTPState This object specifies the spanning tree state on this port.
This object is not applicable to 8300 series products. This
object is not valid on the 9400 series of bo… | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.16 |
| atiStkSwPortId This object specifies the ID of a port present on a given
module. | column | Integer32 | .1.3.6.1.4.1.207.8.17.2.1.1.2 |
| atiStkSwPortName The user-defined ASCII name of the port. | column | OctetString | .1.3.6.1.4.1.207.8.17.2.1.1.3 |
| atiStkSwPortState This object allows the user to either enabled or disabled.
This object can be read to obtain the current state of the port. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.4 |
| atiStkSwPortLinkState This object specifies the link state on this port. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.5 |
| atiStkSwPortNegotiation This object allows an admin request to configure the port
to either autosense or one of the different speed-duplex
combinations. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.6 |
| atiStkSwPortSpeed This object specifies the current speed of the port. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.7 |
| atiStkSwPortDuplexStatus This object specifies the current duplex type used by the
port. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.8 |
| atiStkSwPortFlowControl This object is used to enable/disable flow control on the
port. When enabled, flow control will be full duplex.
Flow control is disabled by default. | column | Enumeration | .1.3.6.1.4.1.207.8.17.2.1.1.9 |