wsAPRadioRTSThreshold
AT-UWC-WLAN-SWITCH-MIB ·
.1.3.6.1.4.1.207.8.42.8.34.3.3.1.15
Object
column
Integer32
This object indicates the number of octets in an MAC Protocol Data Unit(MPDU), below which an request to send(RTS)/clear to send(CTS) handshake shall not be performed.
Context
- MIB
- AT-UWC-WLAN-SWITCH-MIB
- OID
.1.3.6.1.4.1.207.8.42.8.34.3.3.1.15- Type
- column
- Access
- readonly
- Status
- current
- Parent
- wsAPProfileRadioEntry
- Table
- wsAPProfileRadioTable
- Siblings
- 37
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-2347
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wsAPRadioInterface AP physical radio interface number. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.1 |
| wsAPRadioRateLimit Allowed rate limit for broadcast/multicast traffic
transmitted across the network. Broadcast/multicast
traffic below this limit is transmitted normally. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.10 |
| wsAPRadioRateLimitBurst Broadcast/multicast traffic can occur in bursts up to
this value before all traffic is considered to exceed
the limit. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.11 |
| wsAPRadioBeaconInterval Interval at which the AP transmit beacon frames. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.12 |
| wsAPRadioDTIMPeriod Indicates the number of beacons between Delivery Traffic
Indication MAP(DTIM). DTIM indicates buffered broadcast/multicast
traffic on an AP. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.13 |
| wsAPRadioFragmentationThreshold This object limits the size of packets transmitted over the network.
Only even values are allowed in the defined range. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.14 |
| wsAPRadioShortRetryLimit This object indicates the maximum number of transmission attempts on
frame sizes less than or equal to the RTS threshold.
Set action for this object will be supported in next rele… | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.16 |
| wsAPRadioLongRetryLimit This object indicates the maximum number of transmission attempts
on frame sizes greater than the RTS threshold. Set action
for this object will be supported in next release. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.17 |
| wsAPRadioMaxTransmitLifetime This object indicates the elapsed time after the initial
transmission of MAC Service Data Unit(MSDU), after
which further attempts to transmit the MSDU shall be
terminated. Set ac… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.18 |
| wsAPRadioMaxReceiveLifetime This object indicates the elapsed time after the initial
reception of a fragmented MAC Management Protocol Data Unit(MMPDU)
or MSDU, after which further attempts to reassemble
t… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.19 |
| wsAPRadioAdminMode Flag to indicate whether the radio is operational. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.2 |
| wsAPRadioMaxClients Maximum number of client stations that can simultaneously
get associated on this interface. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.20 |
| wsAPRadioAutoPowerMode Flag to indicate power is automatically adjusted by
the controller. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.21 |
| wsAPRadioTxPower If auto power mode is disabled, this object indicates a fixed
power setting for the radio. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.22 |
| wsAPRadioWMMMode Flag to enable/disable Wi-Fi MultiMedia Mode. When enabled,
QOS settings affect both downstream traffic to the sation
and upstream traffic to the AP. When disabled, QOS only appli… | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.23 |
| wsAPRadioLoadBalancingMode Flag to indicate that AP will load balance users on
this radio. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.24 |
| wsAPRadioUtilization If load balancing is enabled, percentage of network utilization
allowed on the radio before clients are denied. This value is
displayed in percentage. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.25 |
| wsAPRadioAutoChannelMode Flag to indicate whether initial AP radio channel assignment
can be automatically adjusted by controller due to changes in
radio performance. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.26 |
| wsAPRadioStationIsolationMode Flag to indicate whether Station Isolation is enabled on the Radio. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.27 |
| wsAPRadioChannelBandwidth Bandwidth used in the channel. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.28 |
| wsAPRadioPrimaryChannel Specify relative location of Primary Channel in the 40 MHz channel. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.29 |
| wsAPRadioFrequency Indicates which physical layer technology to use on radio.
Default value for radio 1 is 'ieee802dot11bgn' and default value
for radio 2 is 'ieee802dot11an'. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.3 |
| wsAPRadioProtectionMode Turn on/off Protection mechanisms. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.30 |
| wsAPRadioShortGuardInterval Dead time, in nanoseconds, between OFDM symbols which prevents
Inter-Symbol and Inter-Carrier Interference (ISI, ICI).
The short guard interval, when enabled, is 400ns and the sta… | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.31 |
| wsAPRadioSTBCMode The Space Time Block Code (STBC) Mode enables the AP to send the
same data stream on multiple antennas at the same time. This is
different from MIMO where the data stream is divid… | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.32 |
| wsAPRadioMulticastTxRate Indicates the data rate AP will send multicast
data to its client stations represented by a count from
2 - 127, corresponding to data rates in multiples of
500 kbit/s from 1 Mbit/… | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.33 |
| wsAPRadioAPSDMode Automatic Power Save Delivery Mode. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.34 |
| wsAPRadioNoAckMode Don't send acknowledgement to correctly received frames. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.35 |
| wsAPRadioResourceMeasEnabled Flag to enable/disable Radio Resource Management (RRM) as
defined in the IEEE 802.11k specification. RRM allows wireless
clients to request adjustments and report conditions regar… | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.36 |
| wsAPRadioQOSEDCATemplate This object indicates the QOS template choice in effect for the profile and radio. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.37 |
| wsAPRadioMinTxPower Minimum Transmit Power that can be set by APA on the radio.
Default Value is 20% for 2.4Ghz Radio and 100% for 5Ghz radio. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.38 |
| wsAPRadioOtherChannelsScanMode When Sentry mode is disabled this flag controls whether the radio moves away from
the operating channel while doing scans. When this mode is disabled the radio scans
only on the o… | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.4 |
| wsAPRadioOtherChannelsScanInterval If scan mode is enable, indicates how often the radio
leaves its operational channel. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.5 |
| wsAPRadioSentryScanMode When Sentry mode is enabled the radio doesn't do any data forwarding, but only periodically
scan channels for rogues. The length of time spent on each channels controlled by the
'… | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.6 |
| wsAPRadioSentryScanChannel If scanning is enabled, this object indicates on which frequencies to
scan. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.7 |
| wsAPRadioScanDuration Indicates how long the radio can scan before returning to its operational
channel. The default value is 10ms. | column | Integer32 | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.8 |
| wsAPRadioRateLimitMode This object enables/disables rate limit for broadcast and multicast
traffic transmitted across the network. | column | Enumeration | .1.3.6.1.4.1.207.8.42.8.34.3.3.1.9 |