wsAPAuthenticationMode

AT-UWC-WLAN-SWITCH-MIB · .1.3.6.1.4.1.207.8.42.8.34.1.5
MIB view Table view

Object

scalar Enumeration 
Flag to indicate if authentication is required for an AP to
establish communication with the controller.

Context

MIB
AT-UWC-WLAN-SWITCH-MIB
OID
.1.3.6.1.4.1.207.8.42.8.34.1.5
Type
scalar
Access
readonly
Status
current
Parent
wsGlobalConfig
Siblings
37

Syntax

Enumeration

Values & Constraints

Enumerated Values
1enable
2disable

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
wsMode
Flag to enable/disable wireless controller functionality on the device. Disable will purge all status and statistics related to wireless functionality.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.1
wsDetectedClientAgeTime
Time in hours to wait before deleting an entry from the detected clients database.A value of 0 in input range means that the entry never ages out.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.10
wsValidAPConfigTable
This table contains configurable parameters for a specific AP. When an AP is discovered and the wsValidationMethod is local, its MAC address is verified in this table to determine…
table-.1.3.6.1.4.1.207.8.42.8.34.1.11
wsGlobalStatusnode-.1.3.6.1.4.1.207.8.42.8.34.1.12
wsGlobalStatisticsnode-.1.3.6.1.4.1.207.8.42.8.34.1.13
wsPeerConfigurationnode-.1.3.6.1.4.1.207.8.42.8.34.1.14
wsClusterPriority
Preference level of the controller to become the Cluster Controller of the Peer Group.A priority of 0 means that the controller can not become cluster controller.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.16
wsAPClientQosMode
Flag to globally enable/disable AP quality-of-service operation for wireless clients.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.17
wsAPAutoUpgradeMode
Flag to enable/disable AP auto upgrade mode. This object is configurable only if the wireless controller supports both 'Integrated' and 'Independent' AP image download modes. If t…
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.18
wsDistTunnelIdleTimeout
Time of inactivity in seconds to wait before terminating a tunnel client.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.19
wsCountryCode
This object indicates country of operation for WLAN. Supported country codes are: Australia - AU, Austria - AT, Austria - AT, Belgium - BE, Brazil - BR, Canada - CA, China - C…
scalarOctetString.1.3.6.1.4.1.207.8.42.8.34.1.2
wsDistTunnelMaxTimeout
Time in seconds to wait before terminating a tunnel client.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.20
wsDistTunnelMaxMcastRepl
Maximum number of multicast replications that can be performed by the AP.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.21
wsDistTunnelMaxClients
Maximum number of clients that can use tunneled through a Home AP.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.22
wsMACAuthenticationMode
This object indicates whether MAC addresses in the Known Client database are granted or denied access if they are in the list, but dont have a specific action.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.23
wsKnownClientTable
This table contains entries of the known clients.
table-.1.3.6.1.4.1.207.8.42.8.34.1.24
wsWidsSecuritynode-.1.3.6.1.4.1.207.8.42.8.34.1.25
wsGlobalRadiusConfigurationnode-.1.3.6.1.4.1.207.8.42.8.34.1.26
wsSwitchStatusTable
This table contain access point and client status parameters of peer controllers of wireless controller.
table-.1.3.6.1.4.1.207.8.42.8.34.1.27
wsSwitchStatisticsTable
This table contain WLAN statistics for every controller in the peer group. Only Cluster Controller can hold the entries for peer controllers. The controller which is not a Cluster…
table-.1.3.6.1.4.1.207.8.42.8.34.1.28
wsAutoIPAssignMode
Flag indicating whether the Wireless feature should automatically assign an IP address from one of the active interfaces or whether the IP address is manually assigned.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.29
wsPeerGroupId
This object indicates which peer group this controller belongs to, there may be more than one group of peer controllers in the WLAN.
scalarInteger32.1.3.6.1.4.1.207.8.42.8.34.1.3
wsSwitchStaticIPAddress
Statically assigned IPv4 address for the Wireless feature. If Auto IP Assignment is true then this setting is ignored.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.207.8.42.8.34.1.30
wsGlobalTspecConfigurationnode-.1.3.6.1.4.1.207.8.42.8.34.1.31
networkMutualAuthMode
Flag to enable/disable mutual authentication of the Wireless controllers and Access Points in the network.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.32
unmanagedAPReprovisioning
Flag to enable/disable reprovisioning of APs when in unmanaged mode.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.33
apProvisionDbAgeTime
Time in hours to wait without hearing any updates for the APs before removing them from the provisioning database.A value of 0 in input range means that the entry never ages out.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.34
switchProvisioning
Flag to enable/disable controller provisioning.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.35
wsIpBasePort
Base IP port.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.36
devLocMeasurementSys
Measurement system in english/metric.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.37
devLocRfScanLocMode
Flag to enable/disable RF Scan location Mode.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.38
devLocRfScanLocInterval
Number of seconds between iterations of triangulation table device location protocol.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.39
wsAPValidationMethod
This object indicates whether or not to verify newly discovered APs and look up their configuration against the local database or a RADIUS server.
scalarEnumeration.1.3.6.1.4.1.207.8.42.8.34.1.4
wsClientRoamAgeTime
Time in seconds to wait after a client disassociates from a managed AP before deleting the client association database entry.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.6
wsRFScanAgeTime
Time in hours to wait before deleting an entry obtained from an RF scan.A value of 0 in input range means that the entry never ages out.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.7
wsAPFailureAgeTime
Time in hours to wait before deleting an entry in the AP association and authentication failure list. A value of 0 in input range means that the entry never ages out.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.8
wsAdHocClientAgeTime
Time in hours to wait before deleting an entry in Ad hoc client list.A value of 0 in input range means that the entry never ages out.
scalarUnsigned32.1.3.6.1.4.1.207.8.42.8.34.1.9