eqptPowerBatDefenseMode
ASAM-EQUIP-MIB ·
.1.3.6.1.4.1.637.61.1.23.18.1.11
Object
column
mandatory
r/w
Enumeration
The battery defense modes offers the operator the possibility to
select the preferred power defense mode in case the system falls
back to the battery mode. The power defense mode is a way to
optimize the power consumption. In R5001 two options are possible.
In later releases additional defense modes will be introduced.
- no battery defense. In this mode the system will run normally,
offering regular service until the battery runs out and the
regular hw defenses are started (Dying Gasp)
- voice priority. In this mode when the system falls back to the
battery the regular service will be maintained until the battery
drains until 90% and will then give priority to the voice LT's by
powering down the DSL LT's. Voice service will be maintained until
the battery runs out and the regular hw defenses are started (Dying
Gasp).
This configuration only possible for planned powermanagement devices,
in this case a planned RANI-B or RPNI-B.
ALCATEL NOTE:
SUPPORT: YES INSRVMOD: NA RANGE: See above
PERSIST: YES DEFVALUE: 0 UNITS: -
Context
- MIB
- ASAM-EQUIP-MIB
- OID
.1.3.6.1.4.1.637.61.1.23.18.1.11- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- eqptPowerEntry
- Table
- eqptPowerTable
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | no-defense |
1 | voice-priority |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| eqptPowerId mandatory Index in equipment Power Table.
Index gives the shelf identification.
ALCATEL NOTE:
SUPPORT: YES INSRVMOD: NA RANGE: See above
PERSIST: NO DEFVALUE: NA UNI… | column | EqptHolderIndex | .1.3.6.1.4.1.637.61.1.23.18.1.1 |
| eqptPowerBatActualCapacity mandatory The capacity (in % of a fully charged battery) of the battery.
The value is only readable when the battery type (eqptPowerBatType)
is configured and the battery is installed and r… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.10 |
| eqptPowerBatDefenseThreshold mandatory The threshold gives an indication of the remaining capacity of the
battery at the moment the defense defined in eqptPowerBatDefenseMode
should be started. The value is in %. In th… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.12 |
| eqptPowerACState mandatory The AC power state will provide an view on the state of the AC Power
supply.
The value is different from no-powermgnt (0) for devices with power
management functionality and AC in… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.13 |
| eqptPowerACFailure mandatory The AC failure state will provide an view on the failure state of
the AC power supply.
This failure state has meaning when eqptPowerACstate different from
default. In other cases … | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.14 |
| eqptPowerNDCaState mandatory The NDCa (Network DC a) state will provide an view on the state of
the Network DC Power supply.
The value is different from no-powermgnt (0) for devices with power
management func… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.15 |
| eqptPowerNDCaFailure mandatory The NDCa failure state will provide an view on the failure state of
the Network DC a power supply.
This failure state has meaning when eqptPowerNDCaState different from
default. I… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.16 |
| eqptPowerNDCbState mandatory The NDCb (Network DC a) state will provide an view on the state of
the Network DC b power supply.
The value is different from no-powermgnt (0) for devices with power
management fu… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.17 |
| eqptPowerNDCbFailure mandatory The NDCb failure state will provide an view on the failure state of
the Network DC b power supply.
This failure state has meaning when eqptPowerNDCbState different from
default. I… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.18 |
| eqptPowerLDCaState mandatory The LDCa power state will provide an view on the state of the local
DC a power supply.
The value is different from no-powermgnt (0) for devices with power
management functionality… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.19 |
| eqptPowerAdminMode mandatory The eqptPowerAdminMode shows the configured power mode.
This configured mode will be used to mask any failures detected
for non-supported modes.
Enumeration is as follows:
0 = … | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.2 |
| eqptPowerLDCaFailure mandatory The LDCa failure state will provide an view on the failure state of
the local DC a power supply.
This failure state has meaning when eqptPowerLDCaState different from
default. In … | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.20 |
| eqptPowerLDCbState mandatory The LDCb power state will provide an view on the state of the local
DC b power suply.
The value is different from no-powermgnt (0) for devices with power
management functionality … | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.21 |
| eqptPowerLDCbFailure mandatory The LDCb failure state will provide an view on the failure state of
the local DC b power supply.
This failure state has meaning when eqptPowerLDCbState different from
default. In … | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.22 |
| eqptPowerInVoltage mandatory Measured incoming voltage in 1/10 Volt
Only supported for devices that host an extended power management
function (e.g RANI-B and RPNI-B).
ALCATEL NOTE:
SUPPORT: YE… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.23 |
| eqptPowerInCurrent mandatory Measured incoming current in 1/10 Ampere
Only supported for devices that host an extended power management
function (e.g RANI-B and RPNI-B).
ALCATEL NOTE:
SUPPORT: … | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.24 |
| eqptPowerInConsumedPower mandatory Calculated incoming consumed power in 1/10 Watt
Only supported for devices that host an extended power management
function (e.g RANI-B and RPNI-B).
ALCATEL NOTE:
SU… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.25 |
| eqptPowerOperMode mandatory The eqptPowerOperMode shows the power mode the NE is using at the
moment of reading.
The VSRM-A (SX) and NGVR (MX) using a power management enabled NTIO
(e.g. RANI-B or RPNI-B) wi… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.3 |
| eqptPowerBatType mandatory This object is used to configure the battery type.
This configuration only possible for planned powermanagement devices,
in this case a planned RANI-B or RPNI-B. Only values for s… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.4 |
| eqptPowerBatStartCapacity mandatory The capacity (Ah) of the battery at the moment of installation.
The value of the capacity is in 1/100 Ah.
Instatiated when eqptPowerBatType is configured.
The configuration of thi… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.5 |
| eqptPowerBatPlannedLifetime mandatory Planned lifetime of the installed battery in 1/10 year.
The planned lifetime, together with the start capacity, is used to
calculate the actual maximal capacity of the battery.
In… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.6 |
| eqptPowerBatState mandatory The battery state will provide a view on the state of the battery.
Possible states are: charging, charged and discharging.
This operational state has meaning for devices that have… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.7 |
| eqptPowerBatFailure mandatory The battery failure state will provide an view on the failure state of
the battery.
This failure state has meaning for devices that have a configured
eqptPowerBatType and eqptPowe… | column | Enumeration | .1.3.6.1.4.1.637.61.1.23.18.1.8 |
| eqptPowerBatTemperature mandatory Measured temperature of the battery in 1/10 Celcius
The value is only readable when the battery type (eqptPowerBatType)
is configured and the battery is installed and reachable.
… | column | Integer32 | .1.3.6.1.4.1.637.61.1.23.18.1.9 |