arrisGpsLastSuccessfulScanTime
ARRIS-GPS-MIB ·
.1.3.6.1.4.1.4115.12.10
Object
scalar
OctetString
Specifies the date and time, when the GPS scan last completed
successfully. This value is retained across reboot and is only
reset after another scan completes successfully or GPSReset is set
to true.
The values for LockedLatitude, LockedLongitude and NumberOfSatellites
correspond to this time. If a scan has never succeeded before, the
value will be the Unknown Time value, as defined in
[Section 3.2/TR-106a4].
The absolute UTC time will be specified as follows (ref: RFC1902):
YYYYMMDDHHMMZ
where:
YYYY - four digits of year
MM - month (01 through 12)
DD - day of month (01 through 31)
HH - hours (00 through 23)
MM - minutes (00 through 59)
Z - the character 'Z' denotes Greenwich Mean Time (GMT).
For example, '199502192015Z' represents 8:15pm GMT on 19 February
1995.
The value of this parameter is persistent in NVRAM.
TR-069/TR-181 reference: Device.FAP.GPS.LastSuccessfulScanTime.
Context
- MIB
- ARRIS-GPS-MIB
- OID
.1.3.6.1.4.1.4115.12.10- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- arrisGpsMib
- Siblings
- 14
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-32
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| arrisGpsScanOnBoot Enables or disables GPS scans during the device start up.
If this MIB is set, the modem will automatically start a GPS
scan when it is power cycled or reset. If a successful lock
… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.12.1 |
| arrisGpsLockedLatitude This parameter specifies the latitude of the device's position in
degrees, multiplied by 1 million. The positive value signifies the
direction, north of the equator. The negative … | scalar | OctetString | .1.3.6.1.4.1.4115.12.11 |
| arrisGpsLockedLongitude This parameter specifies the longitude of the device's position in
degrees, multiplied by 1 million. The positive value signifies the
direction, east of the prime meridian. The ne… | scalar | OctetString | .1.3.6.1.4.1.4115.12.12 |
| arrisGpsNumberOfSatellites The number of satellites that were locked during the test execution.
The greater the number of satellites the better the precision of the
results.
This value is retained across re… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4115.12.13 |
| arrisGpsReset Setting this to true will cause a reset on the GPS Hardware. Setting
this to false has no effect. The value of this parameter is not part
of the device configuration and is always… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.12.14 |
| arrisGpsSuccessfulScanSinceBootup Indicates whether or not the last successful scan occurred since
the last time the modem powered up or reset.
The value of this parameter is not persistent.
TR-069/TR-181 referenc… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.12.15 |
| arrisGpsScanPeriodically Enables or disables periodic GPS scans.
Note that if ScanPeriodically is set to FALSE and either
ScanOnBoot is set to FALSE or the initial scan fails then
the current position (po… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.12.2 |
| arrisGpsPeriodicInterval When ScanPeriodically is true, this value indicates the interval
in seconds at which GPS scan is performed. This time period
represents the amount of time between scans. The scan … | scalar | seconds Unsigned32 | .1.3.6.1.4.1.4115.12.3 |
| arrisGpsPeriodicTime PeriodicTime is used only to set the 'phase' of the GPS scan. The
actual value of PeriodicTime can be arbitrarily far into the past or
future.
For example, if PeriodicInterval is … | scalar | OctetString | .1.3.6.1.4.1.4115.12.4 |
| arrisGpsPowerDownAfterSuccessfulScan Enable/disable the ability to put the GPS to sleep after a
successful scan. When set to FALSE the GPS will run periodically
(if configured) even if a successful scan has occurred… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.12.5 |
| arrisGpsScanTimeout Specifies the time-out value in seconds since the scan started
after which the scan will time out. A timed out scan is to be
reported as C2 with ErrorDetails indicating 'Timed out… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.4115.12.6 |
| arrisGpsScanStatus Indicates the current status of this scan. Enumeration of:
- Indeterminate (The scan has not been executed and there are
no valid scan results available)
- InProg… | scalar | Enumeration | .1.3.6.1.4.1.4115.12.7 |
| arrisGpsErrorDetails Provides more detail when the ScanStatus is either Error or
Error_TIMEOUT.
The value of this parameter is not persistent.
TR-069/TR-181 reference: Device.FAP.GPS.ErrorDetails. | scalar | OctetString | .1.3.6.1.4.1.4115.12.8 |
| arrisGpsLastScanTime The date and time when the last GPS scan completed. Note that
completion does not imply scan success.
The Unknown Time value is returned if no scans have been completed.
The absol… | scalar | OctetString | .1.3.6.1.4.1.4115.12.9 |