arrisCmDevReportLevelsMasterOff
ARRIS-CM-DEVICE-MIB ·
.1.3.6.1.4.1.4115.1.3.1.1.2.3.10
Object
If set to True(1) all Report Levels and Debug Tracing will be turned Off, and Logits Logs will return to thier default values. When this object is read False(2) will be returned.
Context
- MIB
- ARRIS-CM-DEVICE-MIB
- OID
.1.3.6.1.4.1.4115.1.3.1.1.2.3.10- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- arrisCmDevOperationalSetup
- Siblings
- 49
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| arrisCmDevEraseLogBlock If set to True(1) this MIB object will erase the Arris log block. When this object is read
False(2) will be returned. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.11 |
| arrisCmDevEnableDocsis10Plus This object is used to enable/disable DOCSIS 1.0+ operational mode.
This setting is stored into NVRAM and therefore will survive resets.
Set to true(1) t… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.12 |
| arrisCmDevEnableOption177 This object is used to enable/disable sending only DHCP option 177 rather
than sending both option 122 and 177.
This setting is stored into NVRAM and therefore will survive res… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.13 |
| arrisCmDevEnableLoggingPersistence This object is used to enable/disable the telnet logging persistence feature.
This setting is stored into NVRAM and therefore will survive resets.
Set to t… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.14 |
| arrisCmDevModemFeatureSwitch2 This object is used to enable proprietary features of the Arris cable
modem. From left to right, the specified bit indicates whether or not
the corresponding modem feature is e… | scalar | Bits | .1.3.6.1.4.1.4115.1.3.1.1.2.3.15 |
| arrisCmDevDocsQosParamSetActiveTimeout Send QOS Timeout parameter to CMTS for upstream flow IF
feature switch for DSX DQOS is enabled AND the value of this MIB
is set to a value other than the default of 0. | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.1.1.2.3.16 |
| arrisCmDevCLITimeout Max time that a telnet/SSH session can be idle before it is terminated.
Range is 0-1440 minutes, where 0 disables the timer completely. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4115.1.3.1.1.2.3.17 |
| arrisCmDevTODSyncTimeOut This value determines the interval between the TOD sync operations.
Range is 0-4320 hours, where 0 disables the sync completely. This
value sets the interval starting from the… | scalar | Unsigned32 | .1.3.6.1.4.1.4115.1.3.1.1.2.3.18 |
| arrisCmDevDhcpNoSvcImpact This object is used to enable/disable the DHCP RENEW interruption feature.
During an active call DHCP lease renewal will be stalled until all endpoints
are onhook.
Set to off(1) … | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.19 |
| arrisCmDevProvMethodIndicator deprecated Indicates the method used to provision the device. This object should only be
changed by the configuration file. The following provisioning methods are supported:
… | scalar | ArrsCmDevProvMethod | .1.3.6.1.4.1.4115.1.3.1.1.2.3.2 |
| arrisCmDevDhcpOption51Override Enable or Disable the inclusion of DHCP option code 51 in the DHCP REQUEST message.
A value of off(1) will cause DHCP option code 51 to be included in the DHCP
REQUEST message.… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.20 |
| arrisCmDevDEAControl Turn on or off the DEA algorithm. The default value is on(1). | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.21 |
| arrisCmDevSinglePasswd The encoded password--provided by the user--that will be used
for single password access to the CLI & HTTP Advanced Pages.
When read, this object will return a zero-length stri… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4115.1.3.1.1.2.3.22 |
| arrisCmDevTelnetEnable Used to enable/disable Telnet access. TempEnable enables Telnet for
one session only. For Telnet to be enabled, arrisCmDevTelnetAllow must
also be set to 'allow'. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.23 |
| arrisCmDevSSHEnable Used to enable/disable SSH access. TempEnable enables SSH for one
session only. For SSH to be enabled, arrisCmDevSSHAllow must also
be set to 'allow'. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.24 |
| arrisCmDevTelnetAllow Used to allow/inhibit Telnet access. For Telnet to be allowed,
arrisCmDevTelnetEnable must also be set to 'enable'. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.25 |
| arrisCmDevSSHAllow Used to allow/inhibit SSH access. For SSH to be allowed,
arrisCmDevSSHEnable must also be set to 'enable'. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.26 |
| arrisCmDevWirelessRegion This value specifies the region that the modem operates in so it can determine the range of
channels which may be selected by the user for 802.11 operation. This value only
affec… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.27 |
| arrisCmDevRouterMode This value specifies what operating mode should be used by the embedded router in Touchstone
products that include a router. If not specified, the router will be left in its exis… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.28 |
| arrisCmDevEnableDHCPLog Used to enable/disable CM DHCP Logging. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.29 |
| arrisCmDevEnableDocsis20 This object is used to enable/disable DOCSIS 2.0 operation mode.
This object is stored into NVRAM and will be operational after
the next reboot of the device.
Set to true(1) to… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.3 |
| arrisCmDevClearDHCPLog Used to Clear the CM DHCP Logs. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.30 |
| arrisCmDevRouterLanIpAddr This is the current Router Lan IP address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4115.1.3.1.1.2.3.31 |
| arrisCmDevRouterLanSubNetMask This is the current Router Lan Subnet Mask. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4115.1.3.1.1.2.3.32 |
| arrisCmDevRouterLanEnable Used to enable/disable Router Lan. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.33 |
| arrisCmDevRouterLanReset Setting this object to true(1) will reset the Router Lan
Setting this object to false(2) will do nothing.
Reading this object always returns false(2). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.34 |
| arrisCmDevRipTransmitStatus Active when the RIP on puma is actively transmitting RIP
updates. In order for arrisCmDevRipTransmitStatus to be
active, arrisCmDevRouterLanEnable must be enabled, and
all RIP p… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.35 |
| arrisCmDevDectReset Setting this object to true(1) will reset the Dect module
Setting this object to false(2) will do nothing.
Reading this object always returns false(2). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.36 |
| arrisCmDevTftpBlkSize This object is used for the TFTP Blocksize Option (RFC 2348).
Valid values range between 32 and 1448 octets, inclusive.
Setting this object to 0(default) disables this option, and… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4115.1.3.1.1.2.3.37 |
| arrisCmDevTODTimeOffset This mib is used to update CM TOD time offset.
The range of the offset is -12*60*60(-43200) to 13*60*60(46800) in seconds.
13 is Daylight Savings Time in the +12 time zone). The… | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.1.1.2.3.38 |
| arrisCmDevWrmProvServer This object is used to store the TFTP Server Name for the WRM
card if it cannot be included in the DHCP Offer. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4115.1.3.1.1.2.3.39 |
| arrisCmDevModemFeatureSwitch This object is used to enable proprietary features of the Arris cable
modem. From left to right, the specified bit indicates whether or not
the corresponding modem feature is e… | scalar | Bits | .1.3.6.1.4.1.4115.1.3.1.1.2.3.4 |
| arrisCmDevWrmProvFileName This object is used to store the Bootfile name for the WRM
card if it cannot be included in the DHCP Offer. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4115.1.3.1.1.2.3.40 |
| arrisCmDevDSTPolicy This object is used to get and set the daylight saving time policy. This parameter
is a rule with two fields separated by semicolon (;) as shown below:
start=<start-time>;end=<en… | scalar | OctetString | .1.3.6.1.4.1.4115.1.3.1.1.2.3.41 |
| arrisCmDevRestoreNvmFactoryDefault Setting this object to true(1) will reset the NVM to default values:
Setting this object to false(2) will do nothing.
Reading this object always returns false(2). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.42 |
| arrisCmDevWrmProvFile This object is used to store the Bootfile for the WRM
card if it cannot be provisioned by the usual TFTP server. | scalar | OctetString | .1.3.6.1.4.1.4115.1.3.1.1.2.3.43 |
| arrisCmDevUGSTxQueueSize Controls the permitted depth of HW upstream buffer queue for UGS service flows. Packets are discarded if depth of queue exceeds this setting.
A setting of disable (0) indicates t… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.44 |
| arrisCmDevUniqueConfigFileEnable Used to enable/disable downloading the ARRIS unique config file. Default value
is set to 'disable'. This MIB can only be set via the CM config file, but sets will
be ignored if CM… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.45 |
| arrisCmDevUniqueConfigFileServerAddrType This object is used to get and set the IP address mode of the TFTP server for the ARRIS unique
config file. This MIB can only be set via the CM config file, and only IPV4 address… | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.4115.1.3.1.1.2.3.46 |
| arrisCmDevUniqueConfigFileServerAddr This object is used to get and set the TFTP server address that will be used to download the
ARRIS unique config file. This MIB can only be set via the CM config file, and only a … | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.4115.1.3.1.1.2.3.47 |
| arrisCmDevSetupMddIpModeOverride This object is used to override the IP Mode TLV in the MDD message.
0 = use the MDD value
1 = IPv4 Only
2 = IPv6 Only
3 = Alternate (APM)
4 = Dual-stack (DPM) | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.48 |
| arrisCmDevWrmProvFileNameMacEnable When Enabled in the CM configuration file, and the MIB value of
arrisCmDevWrmProvFileName is blank, the CM would generate the MIB
rrisCmDevWrmProvFileName to be the WAN MAC addres… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.49 |
| arrisCmDevHttp | node | - | .1.3.6.1.4.1.4115.1.3.1.1.2.3.5 |
| arrisCmDevTftpMtaIpOverride This object is used to store the TFTP Server IP Address
and it will override the DHCP Offer. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4115.1.3.1.1.2.3.50 |
| arrisCmDevEthernetPower off(0) - power off Ethernet interface.
on(1) - power on Ethernet interface
default(2) - power off Ethernet interface for CM600, power on Ethernet interface for other models. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.51 |
| arrisCmDevTurboDoxConfiguration | node | - | .1.3.6.1.4.1.4115.1.3.1.1.2.3.6 |
| arrisCmDevDhcpServerEnable This object is used to enable/disable the local DHCP Server.
As long as the CM is not operational, the local DHCP Server
is working if enabled. Set to true(1) to enable the DHC… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.1.1.2.3.7 |
| arrisCmDevDhcpServerState Indicates the current state of the local DHCP Server. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.1.1.2.3.8 |
| arrisCmDevScanningSetup | node | - | .1.3.6.1.4.1.4115.1.3.1.1.2.3.9 |