fsRmHbInterval
ARICENT-RM-MIB ·
.1.3.6.1.4.1.2076.99.1.5
Object
scalar
deprecated
r/w
Integer32
The time interval in milli-seconds, between the Heart Beat messages. This value should be 4 times lesser than that of PeerDead Interval. This value must be same for all the nodes in the network. Default value is 500msec. Allowed range of value is from 10 msec to 5 secs.
Context
- MIB
- ARICENT-RM-MIB
- OID
.1.3.6.1.4.1.2076.99.1.5- Type
- scalar
- Access
- readwrite
- Status
- deprecated
- Parent
- fsRm
- Siblings
- 23
Syntax
Integer32
Values & Constraints
Object Constraints
range: 10-5000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsRmSelfNodeId The NodeId of this node | scalar | OctetString | .1.3.6.1.4.1.2076.99.1.1 |
| fsRmSwitchId Slot Number of a Switch in a Stacked environment.
This object is applicable only for Coldstandby case. | scalar | Integer32 | .1.3.6.1.4.1.2076.99.1.10 |
| fsRmConfiguredState The value represents the configured/desired state
of the switch in a Stacked environment
1 - Preferred Master
2 - Backup Master
3 - Preferred Slave
This object is… | scalar | Enumeration | .1.3.6.1.4.1.2076.99.1.11 |
| fsRmStackMacAddr Stack Mac Address of the switch in a Stacked environment.
This object is applicable only for Coldstandby case. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.99.1.12 |
| fsRmPeerTable RM Peer Table consists of Peer infomation in a Stacked environment.
This table is applicable only for Coldstandby case. | table | - | .1.3.6.1.4.1.2076.99.1.13 |
| fsRmStackPortCount The object defines the number of stack ports configured
in a device for the purpose of stacking.
BY default the stack port count will be zero.
If the stack port count is zero, al… | scalar | Integer32 | .1.3.6.1.4.1.2076.99.1.14 |
| fsRmColdStandby The object is for enabling or disabling the
coldstandby stacking support in a stacked environment.
By default it will be disabled. | scalar | Enumeration | .1.3.6.1.4.1.2076.99.1.15 |
| fsRmModuleTrc This object is used to enable the High Availability
enabled module trace.
Currently defined modules as follows:
0x00000001 -- VCM module trace
0x00000002 -- MBSM module trace
0x… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.99.1.16 |
| fsRmProtocolRestartFlag This object is used for enabling or disabling the restart
of all the protocols registered with the RM, in the standby
state, when the ISS node reaches an unpredictable state
like … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.99.1.17 |
| fsRmProtocolRestartRetryCnt This object is used to specify the maximum number of times
the protocols in the ISS switch can be restarted
when the ISS node reaches an unpredictable state.
The protocols will b… | scalar | Unsigned32 | .1.3.6.1.4.1.2076.99.1.18 |
| fsRmHitlessRestartFlag This object is used for hitless restart feature. Initially
this object is set as disable (value = 0). User is allowed to
configure only the value store (value = 1). When this ob… | scalar | Enumeration | .1.3.6.1.4.1.2076.99.1.19 |
| fsRmPeerNodeId The NodeId of the Peer. Currently one peer is supported. | scalar | OctetString | .1.3.6.1.4.1.2076.99.1.2 |
| fsRmIpAddress This object is used only if the Rm stacking interface type is
Inband.This object is used to specify the IP Address to be used
for RM TCP /IP communication .
If RM stac… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.99.1.20 |
| fsRmSubnetMask This object is used only if the Rm stacking interface type is
Inband.This object is used to specify the Subnet Mask to be
associated withIP Address to be used for RM TCP /IP
com… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.99.1.21 |
| fsRmStackInterface This object is used only if the Rm stacking interface type is Inband.This object is used to specify the Stacking port to be used
for RM TCP/IP … | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2076.99.1.22 |
| fsRmCopyPeerSyLogFile The object reflects the status of the log transfer from standby
to active node whether it is in-progress, successful or failed.
The user cannot set the values inProgress, success… | scalar | Enumeration | .1.3.6.1.4.1.2076.99.1.23 |
| fsRmDynamicSyncAuditTrigger This object sets the Application Ids for which dynamic syncup
audit is required.
The Application Ids are defined as follows:
0x0000 -- No Module.
0x0001 -- VCM MODULE.
0x0002 -- … | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.99.1.24 |
| fsRmActiveNodeId The NodeId of the active node. Active node is elected by
discovering the peer node Ip address and then selecting
the node with greater Ip address. | scalar | OctetString | .1.3.6.1.4.1.2076.99.1.3 |
| fsRmNodeState State of the node. The state of the node is decided after
election. Election is based on the NodeId. | scalar | FsRmState | .1.3.6.1.4.1.2076.99.1.4 |
| fsRmPeerDeadInterval The number of milli-seconds that a node's Heart Beat
messages have not seen before declaring peer down. This
value should be 4 times greater than that of the Heart
Beat Interva… | scalar | Integer32 | .1.3.6.1.4.1.2076.99.1.6 |
| fsRmTrcLevel Level of trace required for RM.
The levels are defined as follows:
0x00000001 -- Init-Shut Trace.
0x00000002 -- Management Trace.
0x00000004 -- Data path Trace.
0x00000008 -- Con… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.99.1.7 |
| fsRmForceSwitchoverFlag To force-switchover the ACTIVE node to become STANDBY,
this flag can be enabled.
This object is not saved and restored during mib
save-restore operation
1. enable - Used to tri… | scalar | Enumeration | .1.3.6.1.4.1.2076.99.1.8 |
| fsRmPeerDeadIntMultiplier deprecated The peer dead interval is expressed as a multiple of
heart beat interval. This object is used to store the
multiplier value by which the heart beat interval
is multiplied to get… | scalar | Integer32 | .1.3.6.1.4.1.2076.99.1.9 |