fsMIIpv6ContextDebug
ARICENT-MIIPV6-MIB ·
.1.3.6.1.4.1.29601.2.35.1.1.1.8
Object
Enables the tracing in the selected submodule in IP6. A 32 bit
integer is used to store the Tracing level in the specified module.
Different Tracing Levels -
BIT 1 - Management trace.
BIT 2 - Data path trace.
BIT 3 - Control Plane trace.
BIT 4 - Packet Dump.
BIT 5 - OS Resource trace.
BIT 6 - All Failure trace (All failures including Packet Validation)
BIT 7 - Buffer Trace.
Different submodule Tracing -
BIT 24 - Tracing in IP6 module.
BIT 25 - Tracing in ICMP6 submodule.
BIT 26 - Tracing in ND6 submodule.
BIT 27 - Tracing in UDP6 submodule.
The remaining bits are unused.The combination of levels and submodules
are allowed i.e. Tracing can be allowed at all failure and data path
level in All submodules by setting the BIT appropriately.
For Example, setting the debug value to
00000001000000000000000001000000
will enable all failure trace prints in IP6 module.
Context
- MIB
- ARICENT-MIIPV6-MIB
- OID
.1.3.6.1.4.1.29601.2.35.1.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- fsMIIpv6ContextEntry
- Table
- fsMIIpv6ContextTable
- Siblings
- 15
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsMIIpv6NdCacheMaxRetries This object specifies the maximum number of retries
that can be attempted upon resolving the 'physical'
address of an IPv6 address during address resolution
or unreachability dete… | column | Integer32 | .1.3.6.1.4.1.29601.2.35.1.1.1.1 |
| fsMIIpv6RFC5942Compatibility When the IPv6 node is configured to be RFC5942, ISS compatible
with RFC 5942 and prefix can be configured as on-link. | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.10 |
| fsMIIpv6SENDSecLevel This Object specifies the sec level value for CGA generation in Secure Neighbor Discovery.
Note: For Sec values greater than zero, the above algorithm does not guaranty to termina… | column | Integer32 | .1.3.6.1.4.1.29601.2.35.1.1.1.11 |
| fsMIIpv6SENDNbrSecLevel This object specifies the sec level that are accepted from neighbors in Secure Neighbor
Discovery.
Note: CGA verification should be able to process all security parameter values, … | column | Integer32 | .1.3.6.1.4.1.29601.2.35.1.1.1.12 |
| fsMIIpv6SENDAuthType This object specifies the authorization type to be used in Secure Neighbor Discovery. The options include;
0 indicates only CGA authorization is required.
1 indicates only TA auth… | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.13 |
| fsMIIpv6SENDMinBits This object specifies the minimum acceptable key length.
Note: ISS supports only 512 and 1024 bits key. | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.14 |
| fsMIIpv6SENDSecDAD This object specifies whether to accept the unsecured advertisements, when performing
DAD for Secure Neighbor Discovery in mixed mode. When enabled it implies that secured
adver… | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.15 |
| fsMIIpv6SENDPrefixChk This object specifies the prefix and range check status in Secure Neighbor Discovery.
When enabled it indicates prefix and range checks are relaxed in host. When disabled
it ind… | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.16 |
| fsMIIpv6PmtuConfigStatus Flag to enable or disable Path MTU Discovery for the node. | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.2 |
| fsMIIpv6PmtuTimeOutInterval The time in minutes after which the path MTU entry times out. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.29601.2.35.1.1.1.3 |
| fsMIIpv6JumboEnable Flag to enable or disable IPv6 Jumbogram facility for the node. | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.4 |
| fsMIIpv6NumOfSendJumbo Number of IPv6 Jumbograms sent from the node. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.35.1.1.1.5 |
| fsMIIpv6NumOfRecvJumbo Number of IPv6 Jumbograms received. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.35.1.1.1.6 |
| fsMIIpv6ErrJumbo Number of IPv6 Error Jumbograms received or transmitted. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.35.1.1.1.7 |
| fsMIIpv6RFC5095Compatibility When the IPv6 node is configured to be RFC5095 compatible,
then it should treat Type 0 Routing Header as invalid
routing header type. | column | Enumeration | .1.3.6.1.4.1.29601.2.35.1.1.1.9 |