fsMIBgp4RfdDecayHalfLifeTime
ARICENT-MI-BGP-MIB ·
.1.3.6.1.4.1.29601.2.77.14.1.31
Object
column
r/w
Integer32
The time duration in seconds during which the figure-of-merit will be reduced by half. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured.
Context
- MIB
- ARICENT-MI-BGP-MIB
- OID
.1.3.6.1.4.1.29601.2.77.14.1.31- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- fsMIBgpContextEntry
- Table
- fsMIBgpContextTable
- Siblings
- 60
Syntax
Integer32
Values & Constraints
Object Constraints
range: 600-2700
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsMIBgp4ContextId The index value that uniquely identifies the virtual router in which the configuration is done. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.1 |
| fsMIBgp4AlwaysCompareMED If this object is set to disable, then in best route decision process,
MED will be compared only between routes received from the same
autonomous system. If set to enable, irrespe… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.10 |
| fsMIBgp4DefaultOriginate If this object is set to enable/disable the redistribution and
advertisement of the default route (0.0.0.0/0). By default, the
default routes are not redistributed into BGP. Only … | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.11 |
| fsMIBgp4DefaultIpv4UniCast If this object is set to enable, and if a neighbor is created, then
the MP IPv4 Unicast Address Family Capability will be negotiate for
that peer. If this object is set as disable… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.12 |
| fsMIBgp4IsTrapEnabled If this object is set to disable, then the NOTIFICATION messages wont be sent to
the SNMP Manager. If enabled, NOTIFICATION messages are sent. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.13 |
| fsMIBgp4NextHopProcessingInterval This object is used to configure the interval at which next hops will be mointored for reachablity | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.77.14.1.14 |
| fsMIBgp4IBGPRedistributionStatus If this object is set to enable, IBGP routes will also be redistributed to other
IGP protocols when redistribution is enabled for that protocol | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.15 |
| fsMIBgp4RRDAdminStatus Controls redistribution of Direct, Static, IGP(OSPF,RIP) routes into
BGP. If this object is set to enable, then routes from protocols as
specified by fsMIBgp4RRDProtoMaskForEnable… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.16 |
| fsMIBgp4RRDProtoMaskForEnable The bit mask of source protocols from which routes are
imported to BGP.(LSB corresponds to Bit 0)
Bit 1, if set, indicates that direct routes can be
redis… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.77.14.1.17 |
| fsMIBgp4RRDSrcProtoMaskForDisable The bit mask of source protocols from which redistribution
to BGP is disabled.(LSB corresponds to Bit 0)
Bit 1, if set, indicates that direct routes cannot be
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.77.14.1.18 |
| fsMIBgp4RRDDefaultMetric The default metric value for the IGP routes and static route. If
configured to 0, the metric received from the IGP route will be used.
If configured to other value, the MED value … | column | Unsigned32 | .1.3.6.1.4.1.29601.2.77.14.1.19 |
| fsMIBgp4GlobalAdminStatus The desired state of the BGP system. The BGP4 speaker is
functionally active only when the global admin status is up. The global
admin status can be made up only if the fsMIBgp4Lo… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.2 |
| fsMIBgp4RRDRouteMapName Name Identifies the specified route-map
in the list of route-maps. If this Object needs to be
changed, first reset this object and then configure the
new value. | column | OctetString | .1.3.6.1.4.1.29601.2.77.14.1.20 |
| fsMIBgp4RRDMatchTypeEnable Match type Enable specifies the OSPF route type that
needs to be redistributed into BGP, This object is
used only ospf redistribution. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.21 |
| fsMIBgp4RRDMatchTypeDisable Match type Disable specifies the OSPF route type
that should be disbled from redistribution into BGP.
This object is used only for OSPF protocol. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.22 |
| fsMIBgp4AscConfedId The Local Confederation Identification number of
the AS confederation, a value of zero indicates the
absence of this value. The object fsbgp4LocalAs must be
configured prior to co… | column | Unsigned32 | .1.3.6.1.4.1.29601.2.77.14.1.23 |
| fsMIBgp4AscConfedBestPathCompareMED This object is used to compare MED among paths learned
from confed peers. if this object value is set and AS path
contains only AS_CONFED segments then then MED should be
compare… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.24 |
| fsMIBgp4RflbgpClusterId The configured Cluster-ID of the local router. By default, when the BGP
speaker acts as Route Reflector, the BGP Identifier is used as the
cluster id. Administrator can overwrite … | column | OctetString | .1.3.6.1.4.1.29601.2.77.14.1.25 |
| fsMIBgp4RflRflSupport The desired support of the Route Reflector in the cluster.
Note that none(1) value is for read-only. This object can be set only if
fsMIBgp4LocalAS is configured. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.26 |
| fsMIBgp4RfdCutOff The figure-of-merit value above which the route will be suppressed.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
is set to down and fsMIBgp4LocalAS is configu… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.27 |
| fsMIBgp4RfdReuse The figure-of-merit value below which the suppressed route will be reused.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.28 |
| fsMIBgp4RfdCeiling The highest value the figure-of-merit can attain. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.29 |
| fsMIBgp4Identifier This object configures the BGP Identifier in that VR. If admin status
is made up, by default the BGP Identifier will take
the value of highest interface address. If the BGP Speak… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.29601.2.77.14.1.3 |
| fsMIBgp4RfdMaxHoldDownTime Maximum time (in seconds) a route can be suppressed.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.30 |
| fsMIBgp4RfdDecayTimerGranularity Time granularity in seconds used to perform all decay calculations.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.32 |
| fsMIBgp4RfdReuseTimerGranularity Time interval between evaluations of the reuse lists.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.33 |
| fsMIBgp4RfdReuseIndxArraySize Size of reuse index arrays.This object can be set only if
fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS is
configured. | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.34 |
| fsMIBgp4RfdAdminStatus The desired state of the RouteFlap Dampening feature of the BGP system.
The AricentBGP4 speaker's route flap dampending is functionally active only
when the RFD admin status is en… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.35 |
| fsMIBgp4CommMaxInFTblEntries Maximum Number of Entries in the Input Community Filter Table.
This object can not be set to a higher value than the initial value of the
object.However initial value can be chang… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.36 |
| fsMIBgp4CommMaxOutFTblEntries Maximum number of entries in the outgoing community filter table.
This object can not be set to a higher value than the initial value of the
object.However initial value can be ch… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.37 |
| fsMIBgp4ExtCommMaxInFTblEntries Maximum Number of Entries in the Input Extended Community Filter Table.
This object can not be set to a higher value than the initial value of the
object.However initial value can… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.38 |
| fsMIBgp4ExtCommMaxOutFTblEntries Maximum number of entries in the outgoing extended community filter table.
This object can not be set to a higher value than the initial value of the
object.However initial value … | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.39 |
| fsMIBgp4Synchronization Attribute to enable/disable synchronization within an AS.
This object can be set only if fsMIBgp4LocalAs has been configured. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.4 |
| fsMIBgp4CapabilitySupportAvailable This variable determines whether the Capability Advertisement
Support is enabled or not.This object can be set only if
fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.29601.2.77.14.1.40 |
| fsMIBgp4MaxCapsPerPeer The maximum number of Capabilities that can be supported per peer
or received from peer.
This object can not be set to a higher value than the initial value of the
object.However … | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.41 |
| fsMIBgp4MaxInstancesPerCap The maximum number of Instances of same Capability code can be advertised
to peer or received from peer.
This object can not be set to a higher value than the initial value of the… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.42 |
| fsMIBgp4MaxCapDataSize The maximum size of the Capability Data size of each Capability.
To enable packing, the size should be multiples of 4.
This object can not be set to a higher value than the initia… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.43 |
| fsMIBgp4PreferenceValue Preference value for RIP routes. Use '0' to set default value | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.44 |
| fsMIBgp4ContextStatus this is used to enable or disable status of context | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.45 |
| fsMIBgp4IBGPMaxPaths Maximum number of internal BGP multipath routes to be added per destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwardi… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.46 |
| fsMIBgp4EBGPMaxPaths Maximum number of external BGP multipath routes to be added per destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwardi… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.47 |
| fsMIBgp4EIBGPMaxPaths Maximum number of external plus internal BGP multipath routes (with same AS PATH) to be
added per destination network in Routing table.
When this object takes the value 1, then on… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.48 |
| fsMIBgp4OperIBGPMaxPaths Operational value for Maximum number of internal BGP multipath routes to be added per
destination network in Routing table.
When this object takes the value 1, then only best rou… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.49 |
| fsMIBgp4DefaultLocalPref The default value of local-pref that is to be sent in updates to internal
peers.This object can be set only if fsMIBgp4LocalAs has been configured. | column | Unsigned32 | .1.3.6.1.4.1.29601.2.77.14.1.5 |
| fsMIBgp4OperEBGPMaxPaths Operational value for Maximum number of external BGP multipath routes that to be added
per destination network in Routing table.
When this object takes the value 1, then only be… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.50 |
| fsMIBgp4OperEIBGPMaxPaths Operational value for Maximum number of external plus internal BGP multipath routes
(with same AS PATH) to be added in Routing table.
When this object takes the value 1, then onl… | column | Integer32 | .1.3.6.1.4.1.29601.2.77.14.1.51 |
| fsMIBgp4FourByteASNSupportStatus This object is used to enable or disable 4 byte ASN support in BGP Speaker.
This can be configured only if fsMIBgp4GlobalAdminStatus is down. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.52 |
| fsMIBgp4FourByteASNotationType This object denotes the notation to be used to display the 4 byte ASN. This
will change only the way the AS number is represented within router show
commands in the Command Line I… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.53 |
| fsMIBgp4LocalAsNo This is local autonomous system number specific to a Context. | column | Unsigned32 | .1.3.6.1.4.1.29601.2.77.14.1.54 |
| fsMIBgp4RIBRoutes This is the total number of the routes present in the RIB of a context at the given instance. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.29601.2.77.14.1.55 |
| fsMIBgp4Ipv4AddrFamily This Object is used to enable/disable the ipv4 address family capability for the BGP
virtual context. Enable/Disabling address family will not be immediately reflected on
the su… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.56 |
| fsMIBgp4Ipv6AddrFamily This Object is used to enable/disable the ipv6 address family capability for the BGP
virtual context. Enable/Disabling address family will not be immediately reflected on
the su… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.57 |
| fsMIBgp4VpnLabelAllocPolicy This object denotes the Label Allocation policy. | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.58 |
| fsMIBgp4VPNV4AddrFamily This Object is used to enable/disable the VPNV4 address family capability for the BGP
virtual context. Enable/Disabling address family will not be immediately reflected on
the sup… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.59 |
| fsMIBgp4AdvtNonBgpRt This mib object can be used to configure the peer type to whom
non-bgp routes can be propagated.
external - indicates non-bgp routes can be exported to only
… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.6 |
| fsMIBgp4L2vpnAddrFamily This Object is used to enable/disable the L2vpn address family capability for the BGP
virtual context. Enable/Disabling address family will not be immediately reflected on
the s… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.60 |
| fsMIBgp4EvpnAddrFamily This Object is used to enable/disable the Evpn address family capability for the BGP
virtual context. Enable/Disabling address family will not be immediately reflected on
the supp… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.61 |
| fsMIBgp4TraceEnable This object can be used to enable trace dynamically in BGP
module. A four byte integer value is specified for enabling
the level of tracing.Each Bit in the four byte integer varia… | column | Unsigned32 | .1.3.6.1.4.1.29601.2.77.14.1.7 |
| fsMIBgp4DebugEnable This object can be used to enable debug dynamically in BGP module.
Its a four byte integer value specified for enabling the level
of debugging. Each Bit in the four byte integer v… | column | Unsigned32 | .1.3.6.1.4.1.29601.2.77.14.1.8 |
| fsMIBgp4OverlappingRoute This object is used to configure the BGP speaker's policy for handling
the overlapping routes. When an overlapping route is received, depending
upon the configured policy either t… | column | Enumeration | .1.3.6.1.4.1.29601.2.77.14.1.9 |