fsLsppRepeatCount
ARICENT-LSP-PING-MIB ·
.1.3.6.1.4.1.2076.13.11.2.1.1.10
Object
column
r/w
Unsigned32
This object represents the number of request packets that has to be
sent in a single ping operation. When the fsLsppRequestOwner is set
to 'bfd', the repeat count will be implicitly considered as one.
If the Burst option is set, then this object represents the number of
bursts of packets that has to be sent in a single ping operation.
If the Sweep option is enabled, each packet of the repeat count
will be of different sizes, ranging from the sweep start size to
the sweep end size. When the Request type is set to trace route,
then this is not applicable
Context
- MIB
- ARICENT-LSP-PING-MIB
- OID
.1.3.6.1.4.1.2076.13.11.2.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- fsLsppPingTraceTableEntry
- Table
- fsLsppPingTraceTable
- Siblings
- 50
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 1-2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsLsppSenderHandle Unique handle that identifies a LSP ping or traceroute request. | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.1 |
| fsLsppPacketSize This object specifies the size of the LSP Ping packet along with
the MPLS label stack imposed that is to be sent. Depending on the
value to which the packet size is set, the PAD… | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.11 |
| fsLsppPadPattern This object specifies the pattern to be used in PAD TLV.
This pattern may be repeated in the PAD TLV depending upon the
length of the pattern and the length of the PAD TLV.
This… | column | OctetString | .1.3.6.1.4.1.2076.13.11.2.1.1.12 |
| fsLsppTTLValue This object specifies a time to live value.
In case of ping, by default TTL value will be 255.
If the user sets a particular value, then that TTL will be set and … | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.13 |
| fsLsppWFRInterval Specifies the amount of time to wait to receive a response for a
transmitted MPLS echo request packet before timing out the request. | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.14 |
| fsLsppWFRTmrUnit This object indicates the time unit for the wait-for-reply timer. | column | FsLsppTimeUnit | .1.3.6.1.4.1.2076.13.11.2.1.1.15 |
| fsLsppWTSInterval This object specifies the time between two successive MPLS echo
requests transmitted. This allows the user to pace the transmission
of packets so that the receiving router does … | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.16 |
| fsLsppWTSTmrUnit This object indicates the time unit for the wait-to-send timer. | column | FsLsppTimeUnit | .1.3.6.1.4.1.2076.13.11.2.1.1.17 |
| fsLsppReplyDscpValue This object is to insist on the replying router to provide a
specific class of service (CoS) in an echo reply.
In IP/MPLS and MPLS-TP environments where IP forward… | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.18 |
| fsLsppSweepOption This object specifies if a number of packets of different sizes,
ranging from a start size to an end size are to be sent.
Setting this object to TRUE enables the sweep option.
… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.19 |
| fsLsppRequestType This object indicates whether the request is ping or traceroute. | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.2 |
| fsLsppSweepMinimum This object specifies the minimum or start size of the echo request
packet with which the initiator should send the requests.
The value set in this object wil… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.20 |
| fsLsppSweepMaximum This object specifies the end size of the echo request packet.
The value set in this object will be used when the fsLsppSweepOption
object is set to True.
… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.21 |
| fsLsppSweepIncrement This option specifies size by which echo packet size should be
incremented compared to previous echo request.
The value set in this object will be used when th… | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.22 |
| fsLsppBurstOption This object provides an option to send a burst of echo request
packets of the specified burst size.
Setting this value to True causes the burst option to be enabled.
This object… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.23 |
| fsLsppBurstSize This object specifies the number of echo packets that needs to be
sent in a burst.
This object is applicable only if the fsLsppBurstOption object is
set to t… | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.24 |
| fsLsppEXPValue This object specifies the MPLS experimental field (traffic class
field) value that should be set in the MPLS header for the MPLS
echo packets. | column | Unsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.25 |
| fsLsppDsMap This option is to interrogate a transit router for downstream
mapping (DSMAP) information.
In case of ping, this option is False by default.
For Traceroute this object is implic… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.26 |
| fsLsppFecValidate Setting this object makes the Forward Equivalence Class (FEC)
validation, or in other words, the control versus data plane
verification, to be performed at the responder. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.27 |
| fsLsppReplyPadTlv If this object is true, this gives an indication to the responder
to copy the pad tlv in the reply packet.
By default it is set to false.
PAD T… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.28 |
| fsLsppForceExplicitNull If this object is set to true, EXPLICIT NULL label will be added
at the bottom of the MPLS Label Stack.
This addition of Explicit NULL in the Label Stack allows LS… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.29 |
| fsLsppRequestOwner This object specifies the initiator of this ping or traceroute
request.
management - indicates that the request is initiated from
SNMP/CLI/WEB.… | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.3 |
| fsLsppInterfaceLabelTlv If this object is set to true, this gives an indication to the
responder to add the Interface and Label Stack TLV in the echo
reply packet.
This can be set to tru… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.30 |
| fsLsppSameSeqNumOption If this object is set to true, all the echo request packets as as
indicated by the repeat count, are sent with the same sequence
number.
This object is not applicable for trace… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.31 |
| fsLsppVerbose If this object is set, the originator of the echo request displays
the MPLS echo reply sender address,sequence number, return codes
and return sub-code for every packet in that … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.32 |
| fsLsppReversePathVerify If this object is set to true, the reverse path of an LSP
on which the echo reply is sent, will also be verified.
This should be set only when monitoring MPLS-T… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.11.2.1.1.33 |
| fsLsppEncapType This object specifies the encapsulation type of the LSP Ping packets.
In case of MPLS LSP/Tunnel, the encapsulation type should be set to
mplsIp. For MPLS-TP LSP/Tunnel any one o… | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.34 |
| fsLsppStatus This object indicates the current status of the Ping operation.
inprogress(1) - Operation in progess.
success(2) - Echo reply received successfully
… | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.35 |
| fsLsppActualHopCount If this entry corresponds to a trace route operation and if it is
successful, this object indicates the hopcount to reach to egress
node.
If the trace route operation has failed… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.36 |
| fsLsppResponderAddrType This object specifies whether the address of the sender of the
echo reply packets. This object contains the IPv4 or IPv6 address
type of the replying router in IP/MPLS and MPLS-… | column | FsLsppAddressType | .1.3.6.1.4.1.2076.13.11.2.1.1.37 |
| fsLsppResponderAddr This object contains the IP address of the replying router in
IP/MPLS and MPLS-TP networks when IP addressing is supported.
This object will contain the Node ID of the responder… | column | OctetString | .1.3.6.1.4.1.2076.13.11.2.1.1.38 |
| fsLsppResponderGlobalId This object contains the Global ID of the replying router in
MPLS-TP environments. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.39 |
| fsLsppPathType This object identifies the type of path being monitored.
ldpipv4 or ldpipv6 - indicates that the path pointer is pointing
to a row in FTN… | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.4 |
| fsLsppResponderId This object contains the Node ID of the replying router in the
MPLS-TP environment. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.40 |
| fsLsppMaxRtt This object contains the maximum round-trip time taken for a
successful echo reply for this ping instance. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.41 |
| fsLsppMinRtt This object contains the minimum round-trip time taken for a
successful echo reply for this ping instance. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.42 |
| fsLsppAverageRtt This object contains the average round-trip time taken for a
successful echo reply for this ping instance. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.43 |
| fsLsppPktsTx This object indicates the total number of echo requests that has
been transmitted for this ping or trace route instance. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.13.11.2.1.1.44 |
| fsLsppPktsRx This object indicates the total number of echo replies that has been
recieved for this ping or trace route instance. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.13.11.2.1.1.45 |
| fsLsppPktsUnSent This object indicates the total number of echo packets that has been
unsent due to some issues or errors in framing the packet. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.13.11.2.1.1.46 |
| fsLsppRowStatus This object provides control over the status of this entry.
Setting this object to 'createAndGo' or to 'notInService' is
disallowed.
Setting this object to 'destroy' is valid on… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2076.13.11.2.1.1.47 |
| fsLsppStatusPathDirection This object specifies the direction for which the echo status
is applicable. This object should be interpreted in conjunction
with fsLsppStatus object.
When fsLsp… | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.48 |
| fsLsppResponderIcc This object contains the ICC (ITU Carrier Code) of the replying
router in an ICC based MPLS-TP network. This object is not applicable
for IP based MPLS-TP networks | column | OctetString | .1.3.6.1.4.1.2076.13.11.2.1.1.49 |
| fsLsppPathPointer This object should be interpreted along with the object
fsLsppPathType. This object points to the correponding path details.
If fsLsppPathType is ldpipv4(1) or ldp… | column | SNMPv2-TCRowPointer | .1.3.6.1.4.1.2076.13.11.2.1.1.5 |
| fsLsppResponderUMC This object contains the UMC(Unique MEG code) of the replying
router in an ICC based MPLS-TP network. This object is not applicable
for IP based MPLS-TP networks. | column | OctetString | .1.3.6.1.4.1.2076.13.11.2.1.1.50 |
| fsLsppResponderMepIndex This object contains the administratively assigned Mep Index
of the replying router in ICC based MPLS-TP network.
This object is not applicable for IP based MPLS-TP network. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.51 |
| fsLsppTgtMipGlobalId This object specifies the Global Id of the Target for which ping
has to be initiated. This must be configured in conjunction with
the fsLsppPathType object being set to MEP and t… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.6 |
| fsLsppTgtMipNodeId This object specifies the Node Id of the Target for which ping has to
be initiated. This must be interpreted in conjunction with the
fsLsppTgtMipGlobalId object.
… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.7 |
| fsLsppTgtMipIfNum This object specifies the Interface Number of the Target for
which ping has to be initiated. This must be interpreted in
conjunction with the fsLsppTgtMipGlobalId and the fsLspp… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.11.2.1.1.8 |
| fsLsppReplyMode This object species the reply mode for this particular echo request.
1 - do not reply
2 - reply via an IPv4/IPv6 UDP packet
3 - reply via an IPv4/IPv6 UDP packet with Router Alert… | column | Enumeration | .1.3.6.1.4.1.2076.13.11.2.1.1.9 |