issFirmwareCpldVersion
ARICENT-ISS-MIB ·
.1.3.6.1.4.1.2076.81.1.133
Object
scalar
OctetString
This object specifies the cpld firmware version on the switch
Context
- MIB
- ARICENT-ISS-MIB
- OID
.1.3.6.1.4.1.2076.81.1.133- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- issSystem
- Siblings
- 137
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| issSwitchName System name used for identification of the device. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.1 |
| issConfigSaveOption Specifies whether the configurations of the switch has to be
saved or not.
The value 'noSave' specifies that the configurations need
not be saved.
The value… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.10 |
| issHeartBeatMode The object is for setting the method for Redundancy manager election
mechanism, it can be internal election logic or it can be a external
logic. When this object is set to be in… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.100 |
| issRmRType The object is for setting the type of the Redundancy manager, it can be
Hot or Cold. When this object is set to be cold, whenever there is node
state transition from Standby to Ac… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.101 |
| issRmDType This object specifies the type of the dataplane/hardware, it can be a
shared dataplane or a separate dataplane. When this object is set to
be shared, standby card in a redundancy … | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.102 |
| issClearConfig When the object is set to TRUE, configurations will be cleared and
default configurations will be restored. The value will be reset to
FALSE again. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.103 |
| issClearConfigFileName This is the name of the file, which contains the default configurations
to be restored once configurations are cleared. This is optional. When
this file name is given, configurati… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.104 |
| issTelnetClientStatus This object is for enabling or disabling the TELNET client functionality
in the system. Set operation of enable will allow to establish new Telnet
client sessions. Set operation… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.105 |
| issSshClientStatus This object is for enabling or disabling the SSH client functionality
in the system. Set operation of enable will allow to establish new SSH client
sessions. Set operation of di… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.106 |
| issActiveTelnetClientSessions Specifies the number of active Telnet client sessions running | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.107 |
| issActiveSshClientSessions Specifies the number of active SSH client sessions running | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.108 |
| issLogFileSize This is the maximum file size in bytes of the log file | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.81.1.109 |
| issConfigSaveIpAddr deprecated IP Address of the remote system to which the switch
configurations have to be saved.
This object is valid only if 'issConfigSaveOption' is chosen to be
'remoteSave'. T… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.11 |
| issLogReset Setting this to true ,erases the contents in configs.txt
fileand start logging | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.110 |
| issLogSizeThreshold This is the threshold value of the Log storage space with respect
to the maximum Log Storage Space. It is entered as a percentage value. | scalar | Unsigned32 | .1.3.6.1.4.1.2076.81.1.111 |
| issAutomaticPortCreate This object is for enabling and disabling automatic
port create feature.When set to enabled the ports in
will be automatically created in RSTP module when it
is mapped to a co… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.112 |
| issUlRemoteLogFileName This object is used to specify the filename/filename with path
to which the local file need to be copied in the remote system.
This object is useful only when the 'LogO… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.113 |
| issDefaultExecTimeOut This object is for configuring the default idle time out for
ISS Prompt (exec-time out). | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.81.1.114 |
| issRmStackingInterfaceType This object is used to specify the type of stacking Interface used for
RM communication . Interface can be either an Out of Band port (or)
an Inband Ethernet port. This will be … | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.115 |
| issPeerLoggingOption The Logging option specifying whether the Standby logging is to be
done at console or to a file(system buffer) in the system.
Flash specifies the logging of traces into a file. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.116 |
| issStandbyRestart In a High Availability System, this object allows the user to restart the
Standby switch (i.e) the entire Standby switch will operationally go down and
start again.
… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.117 |
| issRestoreType Specifies whether the restoration type is MIB based save and restore
or CLI based save and restore.
The value 'msr' specifies that the configuration restore will be
in… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.118 |
| issSwitchModeType This MIB object configures switching mode configuration at
switch level. The switching mode configuration done at switch
level will be applied on all the ports in the system inclu… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.119 |
| issConfigSaveFileName Name of the file in which the switch configurations are
to be saved.
This object is valid only if 'issConfigSaveOption' is chosen
to be 'flashSave' or 'remoteSave'. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.12 |
| issConfigRestoreRetries This object is used for configuring the number of retry attempts
for establishing connection with server during remote restore
operation | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.120 |
| issPauseFloodSamplingInterval This object is used to set the sampling interval rate in seconds for pause
flood detection and protection feature. | scalar | seconds Unsigned32 | .1.3.6.1.4.1.2076.81.1.121 |
| issPauseFloodProtect This Object is used to Enable or disable the pause flood detection and
protection feature on all the ports in the system. Enabling this feature
avoids the resource exhaustion cond… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.122 |
| issPauseFloodMode This Object specifies the pause flood mode as disabled/detected-only/enabled
for all the ports in the system.
'disabled' - In this mode, system is not monitored f… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.123 |
| issPauseFloodReset This object is used to recover or re-eanble the pause-flood
detection-only/enabled condition.
Recovery action in Detection-only mode has to log every sampling and clear… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.124 |
| issPauseFloodTraceSeverityLevel This object specifies the value of severity level been configured for pause flood
module's debug tracing. It uses the value 0 (emergency) to 7 (debug). The value 0 is
given to h… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.125 |
| issPauseFloodTraceOption This object is used to store the debug trace types that are enable by the user
for all the interfaces in the system. The bit positions of the traces is shown below.
Bit 0 - no … | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.126 |
| issPortsSwitchingModeStatus This object is used to reflect the switching mode
configuration of each physical port in the hardware.
The switching mode is updated as bit-wise representation.
… | scalar | PortList | .1.3.6.1.4.1.2076.81.1.127 |
| issDebugTimeStampOption This object is used to set the time stamp value in debug trace.
When time stamp is ENABLED, debug traces will be printed with timestamp and
when it is DISABLED, time stamp will no… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.128 |
| issLdapLoginPrivilege This object specifies the default privilege for users authenticated using LDAP. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.129 |
| issInitiateConfigSave When set as 'true' switch configurations save operation is
initiated.
As soon as the configuration save operation is completed, the value
of this object reverts back to 'false'.… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.13 |
| issLdapAttributeName This object specifies the attribute name of the field to be authenticated using LDAP. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.130 |
| issConfigRestoreFileSkuManifest This object specifies the switch models againts which the config file can be used for restoring configuration
String contains supported model numbers separated by ; (e.g. 1;2;3;4) | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.131 |
| issDlImageType This object specifies the image type which will be downloaded | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.132 |
| issHttpMaxSessions This object is used to set HTTP max sessions.
If the max sessions is being reduced, http(s) system is disabled,
are closed all the sessions and enabled again. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.134 |
| issLogInFilter The filter that will be used to keep lines, adding it to console or log file. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.135 |
| issLogOutFilter The filter that will be used to filter out debug message lines from console or log file. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.136 |
| issTrapPowerSupplyStatus Controls generation of the issTrapPowerSupply notification.
When trap conditions are met, the notification is only generated
when this attribute is set to 'enable(1)'. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.137 |
| issTrapFanStatusStatus Controls generation of the issTrapFanStatus notification.
When trap conditions are met, the notification is only generated
when this attribute is set to 'enable(1)'. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.138 |
| issConfigSaveStatus Status of configuration save operation. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.14 |
| issConfigRestoreOption Specifies whether the switch configurations have to be restored
or not.
The value 'noRestore' specifies that the switch configurations
need not be restored when the sys… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.15 |
| issConfigRestoreIpAddr deprecated IP Address of the remote system from where the switch configurations
have to be downloaded to the 'Startup Configuration File' in the flash.
This object is deprecated, as this ob… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.16 |
| issConfigRestoreFileName The configuration file name in the remote system which has to be
downloaded to the 'Startup Configuration File' in the flash. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.17 |
| issInitiateConfigRestore When set as 'true', the switch configurations will be downloaded
from the specified remote system to the 'Startup Configuration File'
in the flash.
As soon as t… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.18 |
| issConfigRestoreStatus The status of the switch configuration restore operation. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.19 |
| issHardwareVersion Version number of the Hardware. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.2 |
| issDlImageFromIp deprecated The Ip Address of machine from where the image has to be downloaded.
This object is deprecated, as this object supports only
IPv4, this IP can be set through issDlImageFromIpvxAdd… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.20 |
| issDlImageName The image name which is to be downloaded to the switch. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.21 |
| issInitiateDlImage Initiates the Image Download operation. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.22 |
| issLoggingOption The Logging option specifying whether the logging is to be
done at console or to a file(system buffer) in the system.
Flash specifies the logging of traces into a file. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.23 |
| issUploadLogFileToIp deprecated The Ip Address of machine to which the log file is to be uploaded.
This object is deprecated, as this object supports only
IPv4, this IP can be set through issUploadLogFileToIpvxA… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.24 |
| issLogFileName The file name to be used for uploading the logs from 'file' to the
remote system.
This object is useful only when the 'LogOption' is chosen as 'file'. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.25 |
| issInitiateUlLogFile Initiates uploading of Log File to the specified IP address in
'issUploadLogFileToIp'.
The logs will be uploaded in the specified 'issLogFileName'. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.26 |
| issRemoteSaveStatus Status of remote save operation.
The remote save operation could be a
a) configuration file save to remote system
b) log file upload to remote system. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.27 |
| issDownloadStatus The status of the Image download operation to the switch. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.28 |
| issSysContact deprecated The textual identification of the contact person for this
managed node, together with information on how to contact
this person. If no contact information is known, the value
is … | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.29 |
| issFirmwareVersion Version number of the Firmware. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.3 |
| issSysLocation deprecated The physical location of this node (e.g., `telephone
closet, 3rd floor'). If the location is unknown, the value
is the zero-length string. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.30 |
| issLoginAuthentication Configures the mechanism by which the user login has to be authenticated
for accessing the GUI to manage the switch. Authentication is done
either locally or in the remote side … | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.31 |
| issSwitchBaseMacAddress Ethernet address (base address) of the Switch.
This base Mac Address, if modified, will take effect only when the
Switch is restarted. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.81.1.32 |
| issOOBInterface Indicates wheteher OOB Interface Exists in the System | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.33 |
| issSwitchDate The date is configured in the switch in the format,
Hours:Minutes:Seconds Day Month Year
e.g 19:10:31 11 08 2005
01-12 Month - beginning from January to December
The … | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.34 |
| issNoCliConsole Indicates whether the CLI console prompt will be made available
to the user for the session through serial console. When set to
TRUE CLI prompt will be available in serial console… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.35 |
| issDefaultIpAddrAllocProtocol Specifies the protocol to be used to obtain IP address for this
interface. This object is valid only when issDefaultIpAddrCfgMode
is set to dynamic (2). Currently rarp (1) optio… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.36 |
| issHttpPort The port to be used by the hosts/PC to configure ISS using the Web Interface.
The HTTP server must be disabled before this configuration is done | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.37 |
| issHttpStatus This object is for enabling or disabling HTTP in the system. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.38 |
| issConfigRestoreFileVersion Config Restoration file version. This version will be compared in each
reboot against version stored in restoration file. Restoration
will occur only if the first field in restor… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.39 |
| issDefaultIpAddrCfgMode Specifies the means by which the default interface in the device
gets the IP address.
If 'manual' mode is selected, the default interface takes the
'issDefaultIpAddr'… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.4 |
| issDefaultRmIfName Name of the default RM interface that can be used for
communication between the Active and Standby nodes for
providing redundancy support.The default RM interface,
if modified,… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.40 |
| issDefaultVlanId The Default VLAN Identifier to be used at system startup.
The VLAN Module creates this vlan as the default vlan.
The Default VLAN Identifier, if modified, will take effect
only … | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.41 |
| issNpapiMode The Mode of NPAPI Processing. It can be
1. Synchronous, 2. Asynchronous. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.42 |
| issConfigAutoSaveTrigger When set as 'true', automatic save operation is enabled. i.e., every
configuration is saved automatically.
When set as 'false', automatic save operation is disabled. i.e.,
conf… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.43 |
| issConfigIncrSaveFlag Indicates whether SNMP Update Trigger for Incremental Save shall be generated or not.
'True' value implies that the update trigger shall be generated each time a nmhSet
operatio… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.44 |
| issConfigRollbackFlag Indicates whether SNMP Rollback feature is enabled or disabled.
'enabled' value implies that failure in set operation for any varbind will result in rollback of all var… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.45 |
| issConfigSyncUpOperation Indicates that sync operation is to be performed.
Incremental save OFF: RB tree, incremental file/buffer are not present in
the system, sync operation is not allowed in t… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.46 |
| issFrontPanelPortCount The object defines the number of physical ports configured
in a device for the purpose of switching/routing. The value
of the object should not exceed system defined MAX physical
… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.47 |
| issAuditLogStatus To Enable or disable Audit Logging | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.48 |
| issAuditLogFileName The name of the file to which Audit log is saved | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.49 |
| issDefaultIpAddr Default IP Address of the system.
This IP address, if modified, will take effect only when the
configuration is stored & restored. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.5 |
| issAuditLogFileSize This is the maximum file size in bytes of the config.txt file | scalar | Unsigned32 | .1.3.6.1.4.1.2076.81.1.50 |
| issAuditLogReset Setting this to true ,erases the contents in configs.txt
fileand start logging | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.51 |
| issAuditLogRemoteIpAddr deprecated IP Address of the remote system to which the
Audit file has to be transfered from flash.
This object is deprecated, as this object supports only
IPv4, this IP can be set through… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.52 |
| issAuditLogInitiateTransfer Setting this will start transfer of the file indicated by
issAuditLogFileName from flash
to remote Address mentioned by issAuditLogRemoteIpAddr | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.53 |
| issAuditTransferFileName The name of the file to be retrieved from flash | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.54 |
| issDownLoadTransferMode To select the Transfer mode for downloading image. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.55 |
| issDownLoadUserName This mib-object is used for setting User name required for downloading
image. When Transfer Mode is selected as tftp, contents of this
mib-object becomes irrelevant. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.56 |
| issDownLoadPassword This mib-object is used for setting password required for downloading
image. When Transfer Mode is selected as tftp, contents of this
mib-object becomes irrelevant. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.57 |
| issUploadLogTransferMode To select the Transfer mode for uploading log file. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.58 |
| issUploadLogUserName This mib-object is used for setting User name required for uploading
log file. When Transfer Mode is selected as tftp, contents of this
mib-object becomes irrelevant. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.59 |
| issDefaultIpSubnetMask IP subnet mask for the default IP address.
This subnet mask, if modified, will take effect only when the
configuration is stored & restored. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.6 |
| issUploadLogPasswd This mib-object is used for setting password required for uploading log file.
When Transfer Mode is selected as tftp, contents of this mib-object becomes
irrelevant. | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.60 |
| issConfigSaveTransferMode To select the Transfer mode for saving the configurations on to a
remote system. Contents of this mib is relevant only when
issConfigSaveOption is remote save. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.61 |
| issConfigSaveUserName This mib-object is used for setting User name required for saving
configurations onto a remote site. Contents of this mib is relevant only
when issConfigSaveOption is remote save… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.62 |
| issConfigSavePassword This mib-object is used for setting Password required for saving
configurations onto a remote site. Contents of this mib is relevant
only when the value of issConfigSaveOption is… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.63 |
| issSwitchMinThresholdTemperature Indicates the minimum threshold temperature of the switch in celsius.
When the current temperature drops below the threshold,
an SNMP trap with maximum severity will be sent to th… | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.64 |
| issSwitchMaxThresholdTemperature Indicates the maximum threshold temperature of the switch in celsius.
When the current temperature rises above the threshold,
an SNMP trap with maximum severity will be sent to th… | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.65 |
| issSwitchCurrentTemperature Indicates the current temperature of the switch in celsius. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.66 |
| issSwitchMaxCPUThreshold Indicates the maximum CPU usage of the switch in percentage.
When CPU load exceeds the threshold value,
an SNMP trap with maximum severity will be sent to the manager. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.67 |
| issSwitchCurrentCPUThreshold Indicates the current CPU threshold of the switch in percentage | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.68 |
| issSwitchPowerSurge Indicates the maximum power supply of the switch in volts.
When the current voltage exceeds the threshold value,
an SNMP trap with maximum severity will be sent to the manager. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.69 |
| issEffectiveIpAddr deprecated Effective IP address of the switch to be used for contacting
through SNMP interface or web interface.
This IP address will be same as the default IP address if the
devi… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.81.1.7 |
| issSwitchPowerFailure Indicates the minimum power supply of the switch in volts.
When the current voltage drops below the threshold value,
an SNMP trap with maximum severity will be sent to the manager. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.70 |
| issSwitchCurrentPowerSupply Indicates the current power supply in volts. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.71 |
| issSwitchMaxRAMUsage Indicates the maximum RAM usage of the switch in percentage.
When the RAM usage crosses the threshold percentage
an SNMP trap with maximum severity will be sent to the manager. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.72 |
| issSwitchCurrentRAMUsage Indicates the current RAM usage of the switch in percentage | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.73 |
| issSwitchMaxFlashUsage Indicates the maximum flash usage of the switch in percentage.
When the flash usage crosses the threshold percentage
an SNMP trap with maximum severity will be sent to the manager. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.74 |
| issSwitchCurrentFlashUsage Indicates the current flash usage of the switch in percentage | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.75 |
| issConfigRestoreFileFormatVersion Config Save Restoration file format Version.This issConfigRestoreFile
FormatVersion value will be compared in each reboot against file format
version value stored in restoration f… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.76 |
| issDebugOption This object stores the trace option string input given by the user.
To enable particular trace the user has to enter
the corresponding string(given below) assigned for that.
And f… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.77 |
| issConfigDefaultValueSaveOption Indicates whether default values needs to be saved or not when
incremental save option is true.'enabled' value implies, MSR stores
default values also when Incremental save is tru… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.78 |
| issConfigSaveIpAddrType This object specifies the address type of the remote system to which
the switch configurations have to be saved.The address type can be
IPv4 or IPv6 unicast address or DNS.
… | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.2076.81.1.79 |
| issDefaultInterface Name of the default interface that can be used for
communicating with the system for configuration through SNMP
or WebInterface.
The default interface, if modified, wi… | scalar | OctetString | .1.3.6.1.4.1.2076.81.1.8 |
| issConfigSaveIpvxAddr This object specifies the IP Address of the remote system to which the switch
configurations have to be saved. It supports DNS host name
when 'issConfigSaveIpAddrType' is of DNS… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.2076.81.1.80 |
| issConfigRestoreIpAddrType This object specifies the IP Address type of the remote system from where
the switch configurations have to be downloaded to the
'Startup Configuration File' in the flash.
The a… | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.2076.81.1.81 |
| issConfigRestoreIpvxAddr This object specifies the IP Address of the remote system from where
the switch configurations have to be downloaded to the
'Startup Configuration File' in the flash.
The addres… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.2076.81.1.82 |
| issDlImageFromIpAddrType This object specifies the address type of machine from where the image
has to be downloaded. The address type can be IPv4 or IPv6
unicast address or DNS. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.2076.81.1.83 |
| issDlImageFromIpvx The IP Address of machine from where the image has to be downloaded. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.2076.81.1.84 |
| issUploadLogFileToIpAddrType This object specifies the address Type of machine to which the log file is
to be uploaded.The address type can be IPv4 or IPv6 unicast address or DNS. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.2076.81.1.85 |
| issUploadLogFileToIpvx This object specifies the address type of machine to which the log file is to be uploaded. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.2076.81.1.86 |
| issAuditLogRemoteIpAddrType IP Address Type of the remote system to which the
Audit file has to be transfered from flash. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.2076.81.1.87 |
| issAuditLogRemoteIpvxAddr IP Address of the remote system to which the
Audit file has to be transfered from flash. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.2076.81.1.88 |
| issSystemTimerSpeed Configures the system timer speed. This is for testing purpose.
Value - 1 enables the timer to run in real time speed.
Values from (2 - 1000), enables the timer to run
(2x - 1000… | scalar | Unsigned32 | .1.3.6.1.4.1.2076.81.1.89 |
| issRestart This object allows the user to restart the Switch
(i.e)the entire switch will operationally go down and
start again. Setting a value of 'true' causes the switch
to be resta… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.81.1.9 |
| issMgmtInterfaceRouting Enables / Disables Routing over the Management Interface.
This object can be configured only if the Management Port
is used for IP Access. | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.90 |
| issMacLearnRateLimit Maximum number of unicast dynamic MAC (L2) entries hardware can learn
in the system, in a configured time interval 'issMacLearnRateLimitInterval'.
In next subsequent time interva… | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.91 |
| issMacLearnRateLimitInterval Number of MAC entries,'issMacLearnRateLimit' that can be learnt in
the system in this configured time interval. Any changed timer interval
value will take effect in next timer res… | scalar | milliseconds Unsigned32 | .1.3.6.1.4.1.2076.81.1.92 |
| issVrfUnqMacFlag Unique mac address can be assigned to each virtual router by enabling
this flag. Configuring this object value will result in updation to
issnvram.file. The configured value will… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.93 |
| issLoginAttempts Number of times a user may be allowed to login using
wrong password in the login prompt. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.94 |
| issLoginLockTime Time in seconds a user is blocked following unsuccessful logins. | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.95 |
| issAuditLogSizeThreshold This is the threshold value of the Log storage space with respect
to the maximum Log Storage Space. It is entered as a percentage value. | scalar | Unsigned32 | .1.3.6.1.4.1.2076.81.1.96 |
| issTelnetStatus This object is for enabling or disabling the TELNET in the system.
Set operation of enable will move this object to the enableInProgress
first then to the enable on successfull tr… | scalar | Enumeration | .1.3.6.1.4.1.2076.81.1.97 |
| issWebSessionTimeOut Set the Web Session Time Out Value in Seconds | scalar | Integer32 | .1.3.6.1.4.1.2076.81.1.98 |
| issWebSessionMaxUsers Set the maximum number of web sessions | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.81.1.99 |