fsipv6SENDSecLevel

ARICENT-IPV6-MIB · .1.3.6.1.4.1.2076.28.1.1.18
MIB view Table view

Object

scalar r/w Integer32 
This Object specifies the sec level value for CGA generation in Secure Neighbor Discovery.
Note: For Sec values greater than zero, the above algorithm does not guaranty to terminate 
after a certain number of iterations (RFC 3972 Section 4)

Context

MIB
ARICENT-IPV6-MIB
OID
.1.3.6.1.4.1.2076.28.1.1.18
Type
scalar
Access
readwrite
Status
current
Parent
fsipv6Scalars
Siblings
24

Syntax

Integer32

Values & Constraints

Object Constraints
range: 0-1

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
fsipv6NdCacheMaxRetries
This object specifies the maximum number of retries that can be attempted upon resolving the 'physical' address of an IPv6 address during address resolution or unreachability dete…
scalarInteger32.1.3.6.1.4.1.2076.28.1.1.1
fsipv6MaxLogicalIfaces
Maximum Number of configurable Logical IPv6 Interfaces
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.10
fsipv6MaxTunnelIfaces
Maximum Number of configurable Tunnel Interfaces
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.11
fsipv6MaxAddresses
Maximum Number of Configurable IPv6 Interfaces.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.12
fsipv6MaxFragReasmEntries
This object could be used for 2 purpose. 1. Maximum Number of IP6 datagrams awaiting reassembly. 2. Maximum Number of fragments that could be allowed in a single reassembly li…
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.13
fsipv6Nd6MaxCacheEntries
Maximum Number of ND Cache Entries.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.14
fsipv6PmtuMaxDest
Maximum Number of PMTU Table Entries
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.15
fsipv6RFC5095Compatibility
When the IPv6 node is configured to be RFC5095 compatible, then it should treat Type 0 Routing Header as invalid routing header type.
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.16
fsipv6RFC5942Compatibility
When the IPv6 node is configured to be RFC5942, ISS compatible with RFC 5942 and prefix can be configured as on-link and off-link.
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.17
fsipv6SENDNbrSecLevel
This object specifies the sec level that are accepted from neighbors in Secure Neighbor Discovery. Note: CGA verification should be able to process all security parameter values, …
scalarInteger32.1.3.6.1.4.1.2076.28.1.1.19
fsipv6PmtuConfigStatus
Flag to enable or disable Path MTU Discovery for the node.
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.2
fsipv6SENDAuthType
This object specifies the authorisation type to be used. The options include; 0 indicates only CGA authorisation is required. 1 indicates only CA authorisation is required. 2 i…
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.20
fsipv6SENDMinBits
This object specifies the minimum acceptable key length. Note: Only 512 and 1024 bits key support available in ISS
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.21
fsipv6SENDSecDAD
In mixed mode Secure Neighbour Discovery, when enabled it indicates secured advertisements are only accepted for first tentative address. When disabled it indicates unsecured adv…
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.22
fsipv6SENDPrefixChk
This object specifies the prefix and range check status. In Secure Neighbor Discovery When enabled it indicates prefix and range checks are relaxed in host. When disabled it ind…
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.23
fsipv6ECMPPRTTimer
Timer value for ECMP PRT.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2076.28.1.1.24
fsipv6NdCacheTimeout
Time after which the entry in cache is deleted.
scalarInteger32.1.3.6.1.4.1.2076.28.1.1.25
fsipv6PmtuTimeOutInterval
The time in minutes after which the path MTU entry times out.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.3
fsipv6JumboEnable
Flag to enable or disable IPv6 Jumbogram facility for the node.
scalarEnumeration.1.3.6.1.4.1.2076.28.1.1.4
fsipv6NumOfSendJumbo
Number of IPv6 Jumbograms sent from the node.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2076.28.1.1.5
fsipv6NumOfRecvJumbo
Number of IPv6 Jumbograms received.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2076.28.1.1.6
fsipv6ErrJumbo
Number of IPv6 Error Jumbograms received or transmitted.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2076.28.1.1.7
fsipv6GlobalDebug
Enables the tracing in the selected submodule in IP6. A 32 bit integer is used to store the Tracing level in the specified module. Different Tracing Levels - BIT 0 - Initialisa…
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.8
fsipv6MaxRouteEntries
Maximum Number of Route Entries that could be configured in the system. Minumum value is 5.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.2076.28.1.1.9