fsipv6GlobalDebug
ARICENT-IPV6-MIB ·
.1.3.6.1.4.1.2076.28.1.1.8
Object
Enables the tracing in the selected submodule in IP6. A 32 bit
integer is used to store the Tracing level in the specified module.
Different Tracing Levels -
BIT 0 - Initialisation and Shutdown Trace.
BIT 1 - Management trace.
BIT 2 - Data path trace.
BIT 3 - Control Plane trace.
BIT 4 - Packet Dump.
BIT 5 - OS Resource trace.
BIT 6 - All Failure trace (All failures including Packet Validation)
BIT 7 - Buffer Trace.
Different submodule Tracing -
BIT 24 - Tracing in IP6 module.
BIT 25 - Tracing in ICMP6 submodule.
BIT 26 - Tracing in ND6 submodule.
BIT 27 - Tracing in UDP6 submodule.
BIT 29 - Tracing in PING6 submodule.
The remaining bits are unused.The combination of levels and submodules
are allowed i.e. Tracing can be allowed at all failure and data path
level in All submodules by setting the BIT appropriately.
For Example, setting the debug value to 00000001000000000000000001000000
will enable all failure trace prints in IP6 module.
Context
- MIB
- ARICENT-IPV6-MIB
- OID
.1.3.6.1.4.1.2076.28.1.1.8- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- fsipv6Scalars
- Siblings
- 24
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsipv6NdCacheMaxRetries This object specifies the maximum number of retries
that can be attempted upon resolving the 'physical'
address of an IPv6 address during address resolution
or unreachability dete… | scalar | Integer32 | .1.3.6.1.4.1.2076.28.1.1.1 |
| fsipv6MaxLogicalIfaces Maximum Number of configurable Logical IPv6 Interfaces | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.10 |
| fsipv6MaxTunnelIfaces Maximum Number of configurable Tunnel Interfaces | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.11 |
| fsipv6MaxAddresses Maximum Number of Configurable IPv6 Interfaces. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.12 |
| fsipv6MaxFragReasmEntries This object could be used for 2 purpose.
1. Maximum Number of IP6 datagrams awaiting reassembly.
2. Maximum Number of fragments that could be allowed in
a single reassembly li… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.13 |
| fsipv6Nd6MaxCacheEntries Maximum Number of ND Cache Entries. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.14 |
| fsipv6PmtuMaxDest Maximum Number of PMTU Table Entries | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.15 |
| fsipv6RFC5095Compatibility When the IPv6 node is configured to be RFC5095 compatible,
then it should treat Type 0 Routing Header as invalid
routing header type. | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.16 |
| fsipv6RFC5942Compatibility When the IPv6 node is configured to be RFC5942, ISS compatible
with RFC 5942 and prefix can be configured as on-link and off-link. | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.17 |
| fsipv6SENDSecLevel This Object specifies the sec level value for CGA generation in Secure Neighbor Discovery.
Note: For Sec values greater than zero, the above algorithm does not guaranty to termina… | scalar | Integer32 | .1.3.6.1.4.1.2076.28.1.1.18 |
| fsipv6SENDNbrSecLevel This object specifies the sec level that are accepted from neighbors in Secure Neighbor
Discovery.
Note: CGA verification should be able to process all security parameter values, … | scalar | Integer32 | .1.3.6.1.4.1.2076.28.1.1.19 |
| fsipv6PmtuConfigStatus Flag to enable or disable Path MTU Discovery for the node. | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.2 |
| fsipv6SENDAuthType This object specifies the authorisation type to be used. The options include;
0 indicates only CGA authorisation is required.
1 indicates only CA authorisation is required.
2 i… | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.20 |
| fsipv6SENDMinBits This object specifies the minimum acceptable key length.
Note: Only 512 and 1024 bits key support available in ISS | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.21 |
| fsipv6SENDSecDAD In mixed mode Secure Neighbour Discovery, when enabled it indicates secured advertisements
are only accepted for first tentative address. When disabled it indicates unsecured
adv… | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.22 |
| fsipv6SENDPrefixChk This object specifies the prefix and range check status. In Secure Neighbor Discovery When
enabled it indicates prefix and range checks are relaxed in host. When disabled it
ind… | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.23 |
| fsipv6ECMPPRTTimer Timer value for ECMP PRT. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.28.1.1.24 |
| fsipv6NdCacheTimeout Time after which the entry in cache is deleted. | scalar | Integer32 | .1.3.6.1.4.1.2076.28.1.1.25 |
| fsipv6PmtuTimeOutInterval The time in minutes after which the path MTU entry times out. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.3 |
| fsipv6JumboEnable Flag to enable or disable IPv6 Jumbogram facility for the node. | scalar | Enumeration | .1.3.6.1.4.1.2076.28.1.1.4 |
| fsipv6NumOfSendJumbo Number of IPv6 Jumbograms sent from the node. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.28.1.1.5 |
| fsipv6NumOfRecvJumbo Number of IPv6 Jumbograms received. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.28.1.1.6 |
| fsipv6ErrJumbo Number of IPv6 Error Jumbograms received or transmitted. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.28.1.1.7 |
| fsipv6MaxRouteEntries Maximum Number of Route Entries that could be configured in
the system. Minumum value is 5. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.28.1.1.9 |