authMode
AQUAMINT-MIB ·
.1.3.6.1.4.1.3942.1.1.5.1.1.1.1.17
Object
column
r/w
Enumeration
Authentication type used - public, static or remote
Context
- MIB
- AQUAMINT-MIB
- OID
.1.3.6.1.4.1.3942.1.1.5.1.1.1.1.17- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- mintNodesEntry
- Table
- mintNodesTable
- Siblings
- 29
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | public |
2 | static |
3 | remote |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| netAddress This value contains node's unique network MAC address. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.1 |
| autoBitrateAddition Correction factor in dB to autobitrate mechanism | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.10 |
| autoBitrateMinLevel Minimal bitrate level for autobitrate mechanism | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.11 |
| extraCost Additional cost to all unit's links to neighbors | column | Integer32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.12 |
| fixedCost Fixed cost to all unit's links to neighbors | column | Integer32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.13 |
| nodeID Node identification number | column | Integer32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.14 |
| ampLow Signal level threshold in dB below which neighbor is unregistred | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.15 |
| ampHigh Signal level exceeding which the unit might become unit's neighbor | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.16 |
| authRelay Shows if the unit is used as an authentication relay | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.18 |
| scrambling Shows if data scrambling is enabled or disabled | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.19 |
| nodeType Node type - master, mesh or slave | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.2 |
| compress Shows if data compression is enabled or disabled | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.20 |
| overTheAirUpgradeEnable Shows the mode of Over-the-Air firmware upgrade mechanism - passive, active or off | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.21 |
| overTheAirUpgradeSpeed Over-the-Air firmware upgrade speed - fast, normal or slow | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.22 |
| roaming Current roaming state | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.23 |
| polling State of polling mechanism. On - polling is on, off - polling is off.
For Polling based firmware only. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.24 |
| mintBroadcastRate Broadcast rate index. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.25 |
| noiseFloor The current noise floor in dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.26 |
| secretKey The secret key for authentication and data scrambling. | column | OctetString | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.27 |
| linksCountReal The parameter represents current number of real neighbors (exclude joins) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.28 |
| rxCapacity The parameter represents current estimated RX capacity in Kbps.
For TDMA based firmware only. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.29 |
| nodeMode Node mode - fixed, nomadic or mobile | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.3 |
| txCapacity The parameter represents current estimated TX capacity in Kbps.
For TDMA based firmware only. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.30 |
| linksCount The parameter represents current number of neighbors | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.4 |
| nodesCount This value contains total network nodes count. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.5 |
| nodeInterfaceId The index value which uniquely identifies the interface to
which this entry is applicable. The interface identified by
a particular value of this index is the same interface as
i… | column | Integer32 | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.6 |
| protocolEnabled MINT protocol state - started or stopped | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.7 |
| nodeName This value contains human-readable string identifying
the node unit. | column | OctetString | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.8 |
| autoBitrateEnable Autobitrate mechanism is either on or off | column | Enumeration | .1.3.6.1.4.1.3942.1.1.5.1.1.1.1.9 |