apsConfigWaitToRestore
APS-MIB ·
.1.3.6.1.2.1.10.49.1.1.2.1.9
Object
column
r/w
seconds Integer32
The Wait To Restore period in seconds.
After clearing of a condition that necessitated an
automatic switch, the wait to restore period must elapse
before reverting. This is intended to avoid rapid switch
oscillations.
GR-253-CORE specifies a Wait To Restore range of 5 to 12
minutes. G.783 defines a 5 to 12 minute Wait To Restore
range in section 5.4.1.1.3, but also allows for a shorter
WTR period in Table 2-1,
WaitToRestore value (MI_WTRtime: 0..(5)..12 minutes).
This object may not be modified if the associated
apsConfigRowStatus object is equal to active(1).
Context
- MIB
- APS-MIB
- OID
.1.3.6.1.2.1.10.49.1.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- apsConfigEntry
- Table
- apsConfigTable
- Siblings
- 10
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: 0-720
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| apsConfigName A textual name for the APS group. | column | OctetString | .1.3.6.1.2.1.10.49.1.1.2.1.1 |
| apsConfigCreationTime The value of sysUpTime at the time the row was
created | column | SNMPv2-TCTimeStamp | .1.3.6.1.2.1.10.49.1.1.2.1.10 |
| apsConfigStorageType The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row. | column | SNMPv2-TCStorageType | .1.3.6.1.2.1.10.49.1.1.2.1.11 |
| apsConfigRowStatus The status of this APS group entry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value. Also,
all associated apsCh… | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.10.49.1.1.2.1.2 |
| apsConfigMode The architecture of the APS group.
onePlusOne
The 1+1 architecture permanently bridges the working
line to the protection line.
oneToN… | column | Enumeration | .1.3.6.1.2.1.10.49.1.1.2.1.3 |
| apsConfigRevert The revertive mode of the APS group.
nonrevertive
Traffic remains on the protection line until another switch
request is received.
rev… | column | Enumeration | .1.3.6.1.2.1.10.49.1.1.2.1.4 |
| apsConfigDirection The directional mode of the APS group.
unidirectional
The unidirectional mode provides protection in one direction.
bidirectional
… | column | Enumeration | .1.3.6.1.2.1.10.49.1.1.2.1.5 |
| apsConfigExtraTraffic This object enables or disables the transfer of extra traffic
on the protection channel in a 1:n architecture. This object
must be set to disabled if the architecture is 1+1. It m… | column | Enumeration | .1.3.6.1.2.1.10.49.1.1.2.1.6 |
| apsConfigSdBerThreshold The Signal Degrade Bit Error Rate.
The negated value of this number is used as the exponent of
10 for computing the threshold value for the Bit Error Rate
(BER). Fo… | column | Integer32 | .1.3.6.1.2.1.10.49.1.1.2.1.7 |
| apsConfigSfBerThreshold The Signal Failure Bit Error Rate.
The negated value of this number is used as the exponent of
10 for computing the threshold value for the Bit Error Rate
(BER). Fo… | column | Integer32 | .1.3.6.1.2.1.10.49.1.1.2.1.8 |