pethPsePortDetectionStatus
ALU-POWER-ETHERNET-MIB ·
.1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.7
Object
column
Enumeration
Describes the operational status of the port PD detection. A value of disabled(1)- indicates that the PSE State diagram is in the state IDLE A value of searching(2)- indicates that the PSE State diagram is in the state DETECTION, CLASSIFICATION, SIGNATURE_INVALID or BACKOFF. A value of deliveringPower(4) - indicates that the PSE State diagram is in the state POWER_UP, POWER_ON or POWER_OFF. A value of fault(5) - indicates that the PSE State diagram is in the state TEST_ERROR or the state IDLE due to the variable error condition. Faults detected are vendor specific. A value of test(7) - indicates that the PSE State diagram is in the state TEST_MODE. A value of denyLowPriority(8) indicates that the port was disabled by the power management system, in order to keep active higher priority ports.
Context
- MIB
- ALU-POWER-ETHERNET-MIB
- OID
.1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.7- Type
- column
- Access
- readonly
- Status
- current
- Parent
- pethPsePortEntry
- Table
- pethPsePortTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | disabled |
2 | searching |
4 | deliveringPower |
5 | fault |
7 | test |
8 | denyLowPriority |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pethPsePortGroupIndex This variable uniquely identifies the group
containing the port to which a power Ethernet PSE is connected.
Group means box in the stack, module in a rack and the value 1
MUST be … | column | Integer32 | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.1 |
| pethPsePortPowerMaintenanceStatus The value ok(1) indicates the Power Maintenance
Signature is present and the overcurrent condition has not been
detected.
The value overCurrent (2) indicates an overcurrent condit… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.10 |
| pethPsePortMPSAbsentCounter Counts the number of times that the
pethPsePortPowerMaintenanceStatus attribute changes from any
value to the value mPSAbsent(3). | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.11 |
| pethPsePortOverCurrentCounter Counts the number of times that the aPSEPowerCurrentStatus
attribute changes from any value to the value overCurrent(2). | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.12 |
| pethPsePortType A manager will set the value of this variable to a value
that indicates the type of the device that is connected
to theport. This value can be the result of the mapping
the addres… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.13 |
| pethPsePortPowerClassifications Classification is a way to tag different terminals on the
Power over LAN network according to their power consumption.
Devices such as IP telephones, WLAN access points and others… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.14 |
| pethPsePortIndex This variable uniquely identifies the power Ethernet PSE
port within group pethPseGroupIndex to which the
power Ethernet PSE entry is connected. | column | Integer32 | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.2 |
| pethPsePortAdminEnable Enables power supply on this port.
Setting this object at a value enable(1) enables power
and detection mechanism for this port.
Setting this object at a value disable(2) disables… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.3 |
| pethPsePortPowerPairsControlAbility Describes the capability of controlling the power pairs
functionality to switch pins for sourcing power.
The value true indicate that the device has the capability
to control the … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.4 |
| pethPsePortPowerPairs Describes or controls the pairs in use. If the value of
pethPsePortPowerPairsControl is true, this object is
writable.
A value of signal(1) means that the signal pairs
only are in… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.5 |
| pethPsePortPowerDetectionControl Controls the power detection mechanism of the port.
Setting the value auto(1) enables the power detection
mechanism of the port.
Setting the value test(2) puts the port in a
testm… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.6 |
| pethPsePortPowerPriority This object controls the priority of the port from the point
of view of a power management algorithm. The priority that
is set by this variable could be used by a control mechanis… | column | Enumeration | .1.3.6.1.4.1.6486.800.1.2.1.27.999.1.1.1.8 |