ethLanPhyPowerOverEthZeroCurrentAlarm
ALFOPLUS-SIAE-MIB ·
.1.3.6.1.4.1.3373.25.25.1.1.24
Object
column
Enumeration
The external device don't draw any current This alarm is risen if the current drawn by the PD is null.
Context
- MIB
- ALFOPLUS-SIAE-MIB
- OID
.1.3.6.1.4.1.3373.25.25.1.1.24- Type
- column
- Access
- readonly
- Status
- current
- Parent
- ethLanPhyRecord
- Table
- ethLanPhyTable
- Siblings
- 25
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | cleared |
2 | activeReportable-Status |
3 | activeReportable-Warning |
4 | activeReportable-Minor |
5 | activeReportable-Major |
6 | activeReportable-Critical |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ethLanPhyUnitId This object is used as Index of the Ethernet Lan PHY Table.
It identifies one of the Equipment's unit | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.25.1.1.1 |
| ethLanPhyInternalLoop Internal loop enable/disable. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.10 |
| ethLanPhyRestartAutoNegotiation This object is used to start a new re-negotiation for automatic
speed, flow control and duplex selection. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.11 |
| ethLanPhyLinkLossAlarm LOS of Signal at Lan port. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.12 |
| ethLanPhySyncAlarm 1000baseX Sync fail | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.13 |
| ethLanPhyAutoNegotiationAlarm Auto Negotiation has failed | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.14 |
| ethLanPhyLinkLossForwardingAlarm Link Loss forwarding is active | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.15 |
| ethLanPhyMasterSlaveAutoNegotiation This object selects if the MASTER/SLAVE role of a 1000 BASE-T port
is set manually or by an auto-negotiation process | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.16 |
| ethLanPhyMasterSlaveManualSelection This object forces the MASTER/SLAVE role of a 1000 BASE-T port, or
sets the preferred role if the auto-negotiation process is enabled
by the leaf ethLanPhyMasterSlaveManualSelecti… | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.17 |
| ethLanPhyMasterSlaveStatus It reflects the status of the MASTER/SLAVE role | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.18 |
| ethLanPhyMasterSlaveConfigurationFaultAlarm MASTER/SLAVE configuration fault detected | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.19 |
| ethLanPhyPortId This object is used as Index of the Ethernet Lan PHY.
It identifies one of the Ethernet ports available on the board.
List of boards:
- board-alfoplus-electrical 2 External por… | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.2 |
| ethLanPhyPowerOverEthEnable This object enable the Power over Ethernet on this electrical
interface | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.20 |
| ethLanPhyPowerOverEthDeviceClass This object indicates the classification of the Powered Device
(PD). The following table outlines IEEE 802.3af-2003 class
categories:
Class Usage PSE out … | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.21 |
| ethLanPhyPowerOverEthHighestClass This object indicates the power available in the Power Sourcing
Equipment (PSE) for the external device.
The value poe-not-available means that Power over Ethernet
module is not p… | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.22 |
| ethLanPhyPowerOverEthOverloadAlarm The external device requires more power than the available one.
This alarm is risen if the requested power by the PD is greater
than the PSE is able to provide. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.23 |
| ethLanPhyLabel ASCII string used to assign a name to LAN tributaries | column | OctetString | .1.3.6.1.4.1.3373.25.25.1.1.25 |
| ethLanPhySsm This object enables or disables the management of SSM
packet for the specified port. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.26 |
| ethLanPhyType This object describes the type of the PHYsical interface: it can
be electrical or optical | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.3 |
| ethLanPhySpeedDuplex It selects the the speed and the duplex mode.
If auto-speed-duplex is selected the speed could be 1G,
oherwise other auto-speed value stops capacity to lower values. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.4 |
| ethLanPhySpeedStatus It reflects the status of the speed | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.5 |
| ethLanPhyDuplexStatus It reflects the status of the Duplex Mode | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.6 |
| ethLanPhyMdiSet It enables or not the Tx/RX signal cross | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.7 |
| ethLanPhyLLF This Integer is a bit string with each bit when set has the
following meaning:
BIT 0 - disable
BIT 1 - enable-local
BIT 2 - enable-degraded BW
BIT 3 - enable-r… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.25.1.1.8 |
| ethLanPhyLineLoop Line loop enable/disable. | column | Enumeration | .1.3.6.1.4.1.3373.25.25.1.1.9 |