alcatelIND1IsisSpbSysOverloadTimeout

ALCATEL-ENT1-ISIS-SPB-MIB · .1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.13
MIB view Table view

Object

scalar r/w seconds Unsigned32 
The value of alcatelIND1IsisSpbSysOverloadTimeout is
the amount of time, in seconds, the router operates
in the overload state before attempting to
reestablish normal operations.  While in overload
state, this IS-IS router will only be used if the
destination is only reachable via this router; it is
not used for other transit traffic.  Operationally
placing the router into the overload state is often
used as a precursor to shutting down the IS-IS
protocol operation.
The value of 0 means the router is in overload
infinitely.

Context

MIB
ALCATEL-ENT1-ISIS-SPB-MIB
OID
.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.13
Type
scalar
Access
readwrite
Status
current
Units
seconds
Parent
alcatelIND1IsisSpbSys
Siblings
20

Syntax

seconds Unsigned32

Values & Constraints

Object Constraints
range: 0-0 range: 60-1800

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
alcatelIND1IsisSpbSysControlBvlan
The vlan tag applied to ISIS-SPB frames.
scalarQ-BRIDGE-MIBVlanId.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.1
alcatelIND1IsisSpbmSysMode
Indication of supporting SPBM mode auto(=1)/manual(=2) auto => enable SPBM mode and auto allocate SPsourceID. manual => enable SPBM mode and manually assign SPsourceID. The defaul…
scalarAlcatelIND1IsisSpbMode.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.10
alcatelIND1IsisSpbSysDigestConvention
The Agreement Digest convention setting off(=1)/loopFreeBoth(=2)/loopFreeMcastOnly(=3) off => disable agreement digest checking in hellos loopFreeBoth => block unsafe group and in…
scalarAlcatelIND1IsisSpbDigestConvention.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.11
alcatelIND1IsisSpbSysSetOverload
Administratively set the overload bit. The overload bit will continue to be set if the implementation runs out of memory, independent of this variable.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.12
alcatelIND1IsisSpbSysOverloadOnBoot
The value of alcatelIND1IsisSpbSysOverloadOnBoot specifies if the router should be in overload state right after the boot up process. If the alcatelIND1IsisSpbSysOverloadOnBoot i…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.14
alcatelIND1IsisSpbSysOverloadOnBootTimeout
The value of alcatelIND1IsisSpbSysOverloadOnBootTimeout is the amount of time, in seconds for which the router operates in the overload state before attempting to reestablish norm…
scalarseconds Unsigned32.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.15
alcatelIND1IsisSpbSysOverloadStatus
Indicates whether or not this isis-spb instance is in overload state. When has the value 'notInOverload', the IS-IS level is normal state. When the value is 'dynamic', the level…
scalarEnumeration.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.16
alcatelIND1IsisSpbSysLastEnabledTime
Contains the sysUpTime value when alcatelIND1IsisSpbSysAdminState was last set to enabled (1) to run the IS-IS protocol.
scalarOctetString.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.17
alcatelIND1isisSpbSysLastSpfRun
Contains the sysUpTime value when the last SPF run was performed for this instance of the IS-IS protocol.
scalarOctetString.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.18
alcatelIND1IsisSpbSysNumLSPs
Specifies the number of LSPs in the database.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.19
alcatelIND1IsisSpbSysAdminState
Controls the operational state of the ISIS-SPB protocol. Default value is disable(2).
scalarEnumeration.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.2
alcatelIND1IsisSpbSysLastEnabledTimeStamp
Contains the sysUpTime value when alcatelIND1IsisSpbSysAdminState was last set to enabled (1) to run the IS-IS protocol.
scalarSNMPv2-TCTimeStamp.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.20
alcatelIND1isisSpbSysLastSpfRunTimeStamp
Contains the sysUpTime value when the last SPF run was performed for this instance of the IS-IS protocol.
scalarSNMPv2-TCTimeStamp.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.21
alcatelIND1IsisSpbSysAreaAddress
The three byte IS-IS Area Address to join. Normally SPB will use area 00-00-00 however if SPB is being used in conjunction with IPV4/V6 it may operate using the IS-IS area address…
scalarAlcatelIND1IsisSpbAreaAddress.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.3
alcatelIND1IsisSpbSysId
SYS ID used for all SPB instances on this bridge. A six byte network wide unique identifier. cf. ieee8021SpbSysId
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.4
alcatelIND1IsisSpbSysControlAddr
Group MAC that the ISIS control plane will use. SPB may use a number of different addresses for SPB Hello and LSP exchange. Section 27.2, 8.13.1.5 and Table 8-13 covers the differ…
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.5
alcatelIND1IsisSpbSysName
Name to be used to refer to this SPB bridge. This is advertised in IS-IS and used for management. cf. ieee8021SpbSysName
scalarAlcatelIND1IsisSpbSystemName.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.6
alcatelIND1IsisSpbSysBridgePriority
This is a 16 bit quantity which ranks this SPB Bridge relative to others when breaking ties. This priority is the high 16 bits of the Bridge Identifier. Its impact depends on the …
scalarAlcatelIND1IsisSpbBridgePriority.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.7
alcatelIND1IsisSpbmSysSPSourceId
The Shortest Path Source Identifier. It is the high order 3 bytes for Group Address DA from this bridge. Note that only the 20 bits not including the top 4 bits are the SPSourceID…
scalarAlcatelIND1IsisSpbmSPsourceId.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.8
alcatelIND1IsisSpbvSysMode
Indication of supporting SPBV mode auto(=1)/manual(=2) auto => enable SPBV mode and auto allocate SPVIDs. manual => enable SPBV mode and manually assign SPVIDs. The default is aut…
scalarAlcatelIND1IsisSpbMode.1.3.6.1.4.1.6486.801.1.2.1.10.17.1.1.1.9