adGenVdsl2VturCurrStatus

ADTRAN-GENVDSL2-LINE-MIB · .1.3.6.1.4.1.664.5.65.1.2.3.1.6

Object

column SNMPv2-SMIUnsigned32

Indicates current state of the Vtur line.  This is a
bit-map of possible conditions.  Due to the isolation
of the Vtur when line problems occur, many state
conditions like loss of power, loss of quality signal,
and initialization errors,  can not be determined.
While trouble shooting Vtur, also use object,
adGenVdsl2VtucCurrStatus.  The various bit positions are:
              
       Bit 00 :        There no defects on the line
              
       Bit 01 :        Vtur failure due to not
                       receiving valid frame.
              
       Bit 02 :        Vtur failure due to not
                       receiving signal.
              
       Bit 03 :        Vtur failure due to loss of
                       power.
                       Note: the Agent may still
                       function.
              
       Bit 04 :        Loss of Signal Quality is
                       declared when the Noise Margin
                       falls below the Minimum Noise
                       Margin, or the bit-error-rate
                       exceeds 10^-7.
              
              
This is intended to supplement ifOperStatus.

Context

MIB: ADTRAN-GENVDSL2-LINE-MIB
OID: .1.3.6.1.4.1.664.5.65.1.2.3.1.6
Type: column
Access: readonly
Status: current
Parent: adGenVdsl2VturPhysEntry
Table: adGenVdsl2VturPhysTable
Siblings: 20

Syntax

SNMPv2-SMIUnsigned32

Source: SNMPv2-SMIUnsigned32
Base type: Unsigned32

Values & Constraints

Type Constraints

range: 0..4294967295

Related Objects

Sibling Objects

Object	Type	Syntax	OID
adGenVdsl2VturInvSerialNumber The vendor specific string that identifies the vendor equipment.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.664.5.65.1.2.3.1.1`
adGenVdsl2VturPrevTxRate The payload rate of the previous successful train.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.10`
adGenVdsl2VturActTxPsd Actual Power Spectrum Density (PSD) transmitted. The average transmit PSD over the sub-carriers. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A…	column	0.1 dB Integer32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.11`
adGenVdsl2VturCurrTxLineRate The line rate, including all payload and overhead rates.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.12`
adGenVdsl2VturPrevTxLineRate The line rate, including all payload and overhead rates, of the previous successful train.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.13`
adGenVdsl2VturCircuitProviderCode Returns remote circuit provider code	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.664.5.65.1.2.3.1.14`
adGenVdsl2VturCircuitCapabilities Returns remote circuit capabilities in bit masks with following order: 0 - Disabled, 1 - Enabled Byte Order of octet string: Byte 0. Byte 1. Byte 2. Byte 3. Byte 4. Byte 5. Byte 6…	column	OctetString	`.1.3.6.1.4.1.664.5.65.1.2.3.1.15`
adGenVdsl2VturCurrTxRateMax Returns max payload rate since last successful train.	column	SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.16`
adGenVdsl2VturCurrTxRateMin Returns min payload rate since last successful train.	column	SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.17`
adGenVdsl2VturLastSraDownshift Returns system uptime of last SRA downshift since last successful train.	column	SNMPv2-TCTimeStamp	`.1.3.6.1.4.1.664.5.65.1.2.3.1.18`
adGenVdsl2VturLastSraUpshift Returns system uptime of last SRA upshift since last successful train.	column	SNMPv2-TCTimeStamp	`.1.3.6.1.4.1.664.5.65.1.2.3.1.19`
adGenVdsl2VturInvVendorID The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.664.5.65.1.2.3.1.2`
adGenVdsl2VturRtxUsed Specifies whether retransmission is active in the transmit direction.	column	Enumeration	`.1.3.6.1.4.1.664.5.65.1.2.3.1.20`
adGenVdsl2VturRtxEtr Expected throughput rate calculated from combined effect of impulse noise protection against worst-case REIN and worst-case SHINE and overhead from correction of stationary noise …	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.21`
adGenVdsl2VturInvVersionNumber The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed a…	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.664.5.65.1.2.3.1.3`
adGenVdsl2CurrDSSnrMgn Noise Margin as seen by this ATU with respect to its received signal in tenth dB.	column	tenth dB Integer32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.4`
adGenVdsl2CurrDSAtn Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.	column	tenth dB Integer32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.5`
adGenVdsl2VturCurrOutputPwr Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.	column	tenth dBm Integer32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.7`
adGenVdsl2VturCurrAttainableRate Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.8`
adGenVdsl2VturCurrTxRate The payload rate of the last successful train.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.664.5.65.1.2.3.1.9`