adGenVdsl2ConfDsTargetSnrMgn
ADTRAN-GENVDSL2-LINE-MIB ·
.1.3.6.1.4.1.664.5.65.1.1.1.1.3
Object
column
r/w
tenth dB Integer32
Configured Target Signal/Noise Margin. This is the noise margin the modem must achieve with the target BER (10-7) or better to successfully complete initialization. The noise margin ranges from 0 to 31 dB with 0.1 dB steps (0..310). This margin should be above the minimum margin and below the maximum margin.
Context
- MIB
- ADTRAN-GENVDSL2-LINE-MIB
- OID
.1.3.6.1.4.1.664.5.65.1.1.1.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Units
- tenth dB
- Parent
- adGenVdsl2LineConfProfileEntry
- Table
- adGenVdsl2LineConfProfileTable
- Siblings
- 115
Syntax
tenth dB Integer32
Values & Constraints
Object Constraints
range: 0-310
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adGenVdsl2LineConfProfileName This object is used by the line configuration table
in order to identify a row of this table.
This value cannot be user-specified and is not dynamic.
… | column | OctetString | .1.3.6.1.4.1.664.5.65.1.1.1.1.1 |
| adGenVdsl2ConfServiceMode The configuration parameter sets the modem service mode. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.10 |
| adGenVdsl2ConfUsLp1CustomRtxIatRein Retransmission inter-arrival time for REIN | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.100 |
| adGenVdsl2ConfUsLp1CustomRtxLeftrThresh Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the… | column | Percent of NDR Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.101 |
| adGenVdsl2ConfDsLp1RtxSetting Retransmission setting | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.102 |
| adGenVdsl2ConfDsLp1CustomRtxMaxNdr Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.103 |
| adGenVdsl2ConfDsLp1CustomRtxMinDelay Retransmission minimum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.104 |
| adGenVdsl2ConfDsLp1CustomRtxMaxDelay Retransmission maximum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.105 |
| adGenVdsl2ConfDsLp1CustomRtxInpMinShine Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.106 |
| adGenVdsl2ConfDsLp1CustomRtxInpMinRein Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.107 |
| adGenVdsl2ConfDsLp1CustomRtxIatRein Retransmission inter-arrival time for REIN | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.108 |
| adGenVdsl2ConfDsLp1CustomRtxLeftrThresh Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the… | column | Percent of NDR Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.109 |
| adGenVdsl2ConfMultiModeDmtTse Multimode DMT Transmission System Enabling (XTSE). A list of the
different modulation types enabled in this profile for multimode.
It is coded in a bit-map representation with 1 … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.11 |
| adGenVdsl2ConfAmRadioFreqMask1 AM radio station 1 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies ar… | column | kHz Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.110 |
| adGenVdsl2ConfAmRadioFreqMask2 AM radio station 2 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies ar… | column | kHz Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.111 |
| adGenVdsl2ConfAmRadioFreqMask3 AM radio station 3 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies ar… | column | kHz Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.112 |
| adGenVdsl2ConfAmRadioFreqMask4 AM radio station 4 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies ar… | column | kHz Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.113 |
| adGenVdsl2ConfAmRadioFreqMask5 AM radio station 5 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies ar… | column | kHz Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.114 |
| adGenVdsl2ConfAmRadioFreqMask6 AM radio station 6 center frequency in kHz. Carrier
frequencies around this center frequency will be masked
off. The value 0 will disable the masking of the carrier
frequencies ar… | column | kHz Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.115 |
| adGenVdsl2ConfMemorySplitRatio This parameter defines the ratio of how the interleaver memory
is allocated between the downstream and upstream directions.
For example a ratio of 2:1 will assign twice as much in… | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.116 |
| adGenVdsl2ConfBandProfiles Bit-map of ITU-T G.993.2 implementation profiles supported by
an VTU-x and can be provisioned on the VDSL2 line.
Bit Assignments:
Bit 00: Profile 8A… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.12 |
| adGenVdsl2ConfSpecificPsdSelect The VDSL2 specific PSD selections to be used in the upstream
and downstream directions. The validity of these selections
is dependent of the VDSL2 band profile selection. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.13 |
| adGenVdsl2ConfUsPsdMaskU0Select Enable or disable of the use of the VDSL2 U0 band in the
upstream direction. U0 is a relatively small frequency band
of operation used by ADSL2+/ADSL2/ADSL modems. It is optiona… | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.14 |
| adGenVdsl2ConfUsTrellis Enable or disable Upstream Trellis Encoding. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.15 |
| adGenVdsl2ConfDsTrellis Enable or disable Downstream Trellis Encoding. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.16 |
| adGenVdsl2ConfUsPboSetting Defines the Upstream Power Backoff mode setting. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.17 |
| adGenVdsl2ConfDsPboSetting Defines the Downstream Power Backoff mode setting. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.18 |
| adGenVdsl2ConfUsVnoiseSetting Defines upstream virtual noise setting. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.19 |
| adGenVdsl2ConfDsRateMode Defines what form of downstream rate adaptation is
configured on this modem. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.2 |
| adGenVdsl2ConfDsVnoiseSetting Defines downstream virtual noise setting. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.20 |
| adGenVdsl2ConfUsBitSwap Defines upstream Bit Swap to be enabled or not. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.21 |
| adGenVdsl2ConfDsBitSwap Defines downstream Bit Swap to be enabled or not. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.22 |
| adGenVdsl2ConfHamBandNotches A bit-map of transmit power spectral density mask code, used
to avoid interference with HAM (Handheld Amateur Radio)
radio bands by introducing power control (notching) in one
or … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.23 |
| adGenVdsl2ConfUsNomAggTxPwr The maximum nominal aggregate transmit power in the upstream
direction during initialization and Showtime. It ranges from
0 to 255 units of 0.1 dBm (physical values are 0 to 25.5… | column | Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.24 |
| adGenVdsl2ConfDsNomAggTxPwr The maximum nominal aggregate transmit power in the
downstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.25 |
| adGenVdsl2ConfUsMaxNomTxPsd This parameter represents the maximum nominal transmit PSD in
the upstream direction during initialization and showtime
(in dBm/Hz). It ranges from -60 to -30 dBm/Hz, with 0.1 dB … | column | Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.26 |
| adGenVdsl2ConfDsMaxNomTxPsd This parameter represents the maximum nominal transmit PSD in
the downstream direction during initialization and showtime
(in dBm/Hz). It ranges from -60 to -30 dBm/Hz, with 0.1 d… | column | Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.27 |
| adGenVdsl2ConfUsMaxAggRxPwr The maximum upstream aggregate receive power over the relevant
set of sub-carriers. The xTU-C should verify that the
upstream power cutback is such that this maximum aggregate
re… | column | Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.28 |
| adGenVdsl2ConfFramingMode This is the PMS-TC layer Framing mode setting. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.29 |
| adGenVdsl2ConfUsLp0MaxPayloadRate Latency Path 0 upstream maximum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.30 |
| adGenVdsl2ConfUsLp0MinPayloadRate Latency Path 0 upstream minimum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.31 |
| adGenVdsl2ConfUsLp0MaxDelay Latency Path 0 upstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the beta … | column | msec Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.32 |
| adGenVdsl2ConfUsLp0MinProtection Latency Path 0 upstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A va… | column | 0.5 Sym Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.33 |
| adGenVdsl2ConfUsLp0RaRatio This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The rat… | column | % Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.34 |
| adGenVdsl2ConfUsLp0InitPolicy Selects the US latency path 0 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp). | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.35 |
| adGenVdsl2ConfDsLp0MaxPayloadRate Latency Path 0 downstream maximum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.36 |
| adGenVdsl2ConfDsLp0MinPayloadRate Latency Path 0 downstream minimum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.37 |
| adGenVdsl2ConfDsLp0MaxDelay Latency Path 0 downstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the bet… | column | msec Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.38 |
| adGenVdsl2ConfDsLp0MinProtection Latency Path 0 downstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A … | column | 0.5 Sym Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.39 |
| adGenVdsl2ConfDsMaxSnrMgn Configured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation. The noise marg… | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.4 |
| adGenVdsl2ConfDsLp0RaRatio This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The rat… | column | % Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.40 |
| adGenVdsl2ConfDsLp0InitPolicy Selects the DS latency path 0 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp). | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.41 |
| adGenVdsl2ConfUsLp1MaxPayloadRate Latency Path 1 upstream maximum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.42 |
| adGenVdsl2ConfUsLp1MinPayloadRate Latency Path 1 upstream minimum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.43 |
| adGenVdsl2ConfUsLp1MaxDelay Latency Path 1 upstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the beta … | column | msec Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.44 |
| adGenVdsl2ConfUsLp1MinProtection Latency Path 1 upstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A va… | column | 0.5 Sym Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.45 |
| adGenVdsl2ConfUsLp1RaRatio This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The rat… | column | % Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.46 |
| adGenVdsl2ConfUsLp1InitPolicy Selects the US latency path 1 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp). | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.47 |
| adGenVdsl2ConfDsLp1MaxPayloadRate Latency Path 1 downstream maximum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.48 |
| adGenVdsl2ConfDsLp1MinPayloadRate Latency Path 1 downstream minimum payload data rate. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.49 |
| adGenVdsl2ConfDsMinSnrMgn Configured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the … | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.5 |
| adGenVdsl2ConfDsLp1MaxDelay Latency Path 1 downstream maximum Interleave Delay.
This parameter is the maximum one-way interleaving delay
in milli-seconds introduced by the PMS-TC between the
alfa and the bet… | column | msec Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.50 |
| adGenVdsl2ConfDsLp1MinProtection Latency Path 1 downstream Minimum Impulse Noise Protection.
This parameter specifies the minimum impulse noise
protection for the latency path in 0.5 fractions of DMT
symbols. A … | column | 0.5 Sym Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.51 |
| adGenVdsl2ConfDsLp1RaRatio This parameter (expressed in %) specifies the ratio that
should be taken into account for the latency path when
performing rate adaptation in the direction of the
channel. The rat… | column | % Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.52 |
| adGenVdsl2ConfDsLp1InitPolicy Selects the DS latency path 1 channel framing parameter
policy during initialization. The options are to
maximize net data rate (ndr) or impulse noise
protection (inp). | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.53 |
| adGenVdsl2ConfUsLp0Type Selects the US latency path 0 channel type options. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.54 |
| adGenVdsl2ConfDsLp0Type Selects the DS latency path 0 channel type options. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.55 |
| adGenVdsl2ConfUsLp1Type Selects the US latency path 1 channel type options. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.56 |
| adGenVdsl2ConfDsLp1Type Selects the DS latency path 1 channel type options. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.57 |
| adGenVdsl2ConfUsRateMode Defines what form of upstream rate adaptation is
configured on this modem. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.58 |
| adGenVdsl2ConfUsCustomPboElecLenKL Upstream power back-off electrical length (KL0). | column | 0.1 dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.59 |
| adGenVdsl2ConfUsTargetSnrMgn Configured Target Signal/Noise Margin. This is the noise
margin the modem must achieve with the target BER (10-7)
or better to successfully complete initialization. The
noise ma… | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.6 |
| adGenVdsl2ConfUsCustomPboForceLen Upstream power back-off force electrical length. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.60 |
| adGenVdsl2ConfUsCustomPboBoostMode Upstream power back-off boost mode. | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.61 |
| adGenVdsl2ConfDsCustomPboElecLen Downstream G997.1 Exchange side electrical length. only multiples of .5 are valid | column | 0.1 dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.62 |
| adGenVdsl2ConfDsCustomPboCableA Downstream G997.1 Exchange side cable parameter A. | column | scalar Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.63 |
| adGenVdsl2ConfDsCustomPboCableB Downstream G997.1 Exchange side cable parameter B. | column | scalar Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.64 |
| adGenVdsl2ConfDsCustomPboCableC Downstream G997.1 Exchange side cable parameter C. | column | scalar Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.65 |
| adGenVdsl2ConfDsCustomPboMinSignal Downstream G997.1 Minimum Usable Signal. only multiples of .5 are valid | column | 0.1 dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.66 |
| adGenVdsl2ConfDsCustomPboMinFreq Downstream G997.1 Minimum Power Backoff Frequency | column | 4.3125kHz tones Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.67 |
| adGenVdsl2ConfDsCustomPboMaxFreq Downstream G997.1 Maximum Power Backoff Frequency | column | 4.3125kHz tones Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.68 |
| adGenVdsl2ConfAnfpCalValue ANFP loss calibration value | column | dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.69 |
| adGenVdsl2ConfUsMaxSnrMgn Configured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation. The noise marg… | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.7 |
| adGenVdsl2ConfDsDownshiftSnrMgn Threshold SNR margin to trigger a downstream downshift. | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.70 |
| adGenVdsl2ConfDsUpshiftSnrMgn Threshold SNR margin to trigger a downstream upshift. | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.71 |
| adGenVdsl2ConfDsMinUpshiftTime Minimum configured time that must elapse
between downstream upshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift. | column | seconds Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.72 |
| adGenVdsl2ConfDsMinDownshiftTime Minimum configured time that must elapse
between downstream downshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift. | column | seconds Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.73 |
| adGenVdsl2ConfUsDownshiftSnrMgn Threshold SNR margin to trigger a upstream downshift. | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.74 |
| adGenVdsl2ConfUsUpshiftSnrMgn Threshold SNR margin to trigger a upstream upshift. | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.75 |
| adGenVdsl2ConfUsMinUpshiftTime Minimum configured time that must elapse
between upstream upshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift. | column | seconds Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.76 |
| adGenVdsl2ConfUsMinDownshiftTime Minimum configured time that must elapse
between upstream downshifts. A value of 2
indicates a downshift cannot occur unless 2
seconds have elapsed since the previous
downshift. | column | seconds Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.77 |
| adGenVdsl2ConfUsLp0RtxSetting Retransmission setting | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.78 |
| adGenVdsl2ConfUsLp0CustomRtxMaxNdr Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.79 |
| adGenVdsl2ConfUsMinSnrMgn Configured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the … | column | tenth dB Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.8 |
| adGenVdsl2ConfUsLp0CustomRtxMinDelay Retransmission minimum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.80 |
| adGenVdsl2ConfUsLp0CustomRtxMaxDelay Retransmission maximum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.81 |
| adGenVdsl2ConfUsLp0CustomRtxInpMinShine Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.82 |
| adGenVdsl2ConfUsLp0CustomRtxInpMinRein Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.83 |
| adGenVdsl2ConfUsLp0CustomRtxIatRein Retransmission inter-arrival time for REIN | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.84 |
| adGenVdsl2ConfUsLp0CustomRtxLeftrThresh Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the… | column | Percent of NDR Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.85 |
| adGenVdsl2ConfDsLp0RtxSetting Retransmission setting | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.86 |
| adGenVdsl2ConfDsLp0CustomRtxMaxNdr Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.87 |
| adGenVdsl2ConfDsLp0CustomRtxMinDelay Retransmission minimum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.88 |
| adGenVdsl2ConfDsLp0CustomRtxMaxDelay Retransmission maximum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.89 |
| adGenVdsl2LineConfProfileRowStatus This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to
`active'. When `active' is… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.664.5.65.1.1.1.1.9 |
| adGenVdsl2ConfDsLp0CustomRtxInpMinShine Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.90 |
| adGenVdsl2ConfDsLp0CustomRtxInpMinRein Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.91 |
| adGenVdsl2ConfDsLp0CustomRtxIatRein Retransmission inter-arrival time for REIN | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.92 |
| adGenVdsl2ConfDsLp0CustomRtxLeftrThresh Retransmission parameter that specifies the fraction of
the NDR used as the threshold to declare leftr defects.
A minimum value of ETR/2 is required. A special value
of 0 sets the… | column | Percent of NDR Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.93 |
| adGenVdsl2ConfUsLp1RtxSetting Retransmission setting | column | Enumeration | .1.3.6.1.4.1.664.5.65.1.1.1.1.94 |
| adGenVdsl2ConfUsLp1CustomRtxMaxNdr Retransmission maximum allowed net data rate.
Valid values are in 8000 bps increments. | column | bps Unsigned32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.95 |
| adGenVdsl2ConfUsLp1CustomRtxMinDelay Retransmission minimum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.96 |
| adGenVdsl2ConfUsLp1CustomRtxMaxDelay Retransmission maximum allowed delay | column | ms Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.97 |
| adGenVdsl2ConfUsLp1CustomRtxInpMinShine Retransmission minimum impulse noise protection against
SHINE when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.98 |
| adGenVdsl2ConfUsLp1CustomRtxInpMinRein Retransmission minimum impulse noise protection against
REIN when subcarrier spacing is 4.3125Khz | column | DMT symbols Integer32 | .1.3.6.1.4.1.664.5.65.1.1.1.1.99 |