adsl2LConfProfRfiBandsDs
ADSL2-LINE-MIB ·
.1.3.6.1.2.1.10.238.1.5.1.2.1.4
Object
The subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It is a bitmap of 512 bits that allows referring to up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is part of a notch filter, and if set to '0', the respective sub-carrier is not part of a notch filter. This information complements the specification provided by adsl2LConfProfPsdMaskDs. Note that if NSCds < 512, all bits i (NSCds<i<512) should be set to '0'.
Context
- MIB
- ADSL2-LINE-MIB
- OID
.1.3.6.1.2.1.10.238.1.5.1.2.1.4- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adsl2LineConfProfEntry
- Table
- adsl2LineConfProfTable
- Siblings
- 28
Syntax
ADSL2-LINE-TC-MIBAdsl2RfiDs
- Source
- ADSL2-LINE-TC-MIBAdsl2RfiDs
- Base type
OctetString
Values & Constraints
Type Constraints
range: 0..64
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adsl2LConfProfProfileName This object identifies a row in this table. | column | OctetString | .1.3.6.1.2.1.10.238.1.5.1.2.1.1 |
| adsl2LConfProfRaUsTimeUs The Upstream Up-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay above the
Upstream Up-… | column | seconds Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.10 |
| adsl2LConfProfRaDsNrmsDs The Downstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below that … | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.11 |
| adsl2LConfProfRaDsNrmsUs The Upstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays … | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.12 |
| adsl2LConfProfRaDsTimeDs The Downstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time the downstream noise margin should stay below the
Downst… | column | seconds Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.13 |
| adsl2LConfProfRaDsTimeUs The Upstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay below the Upstream
D… | column | seconds Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.14 |
| adsl2LConfProfTargetSnrmDs The minimum Noise Margin the ATU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.15 |
| adsl2LConfProfTargetSnrmUs The minimum Noise Margin the ATU-C receiver shall achieve,
relative to the BER requirement for each of the upstream
bearer channels, to successfully complete initialization.
The t… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.16 |
| adsl2LConfProfMaxSnrmDs The maximum Noise Margin the ATU-R receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-R
shall request that the ATU-C reduce the ATU-C transmit power
… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.17 |
| adsl2LConfProfMaxSnrmUs The maximum Noise Margin the ATU-C receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-C
shall request that the ATU-R reduce the ATU-R … | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.18 |
| adsl2LConfProfMinSnrmDs The minimum Noise Margin the ATU-R receiver shall tolerate.
If the noise margin falls below this level, the ATU-R shall
request that the ATU-C increase the ATU-C transmit power.
I… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.19 |
| adsl2LConfProfScMaskDs Sub-carriers mask. A bitmap of 512 bits that allows masking
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective
downst… | column | ADSL2-LINE-TC-MIBAdsl2ScMaskDs | .1.3.6.1.2.1.10.238.1.5.1.2.1.2 |
| adsl2LConfProfMinSnrmUs The minimum Noise Margin the ATU-C receiver shall tolerate.
If the noise margin falls below this level, the ATU-C shall
request that the ATU-R increase the ATU-R transmit power.
I… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.20 |
| adsl2LConfProfMsgMinUs Minimum Overhead Rate Upstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in upstream direction. Expressed in bits per second an… | column | bits/second Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.21 |
| adsl2LConfProfMsgMinDs Minimum Overhead Rate Downstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in downstream direction. Expressed in bits per secon… | column | bits/second Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.22 |
| adsl2LConfProfAtuTransSysEna ATU Transmission System Enabling (ATSE). A list of the
different coding types enabled in this profile. It is coded
in a bit-map representation with 1 or more bits set. A bit
se… | column | ADSL2-LINE-TC-MIBAdsl2TransmissionModeType | .1.3.6.1.2.1.10.238.1.5.1.2.1.23 |
| adsl2LConfProfPmMode Power management state Enabling. Defines the power states the
ATU-C or ATU-R may autonomously transition to on this line.
The various bit positions are: allowTransitionsToIdle(0)… | column | ADSL2-LINE-TC-MIBAdsl2LConfProfPmMode | .1.3.6.1.2.1.10.238.1.5.1.2.1.24 |
| adsl2LConfProfL0Time This minimum time (in seconds) between an Exit from the L2
state and the next Entry into the L2 state. It ranges from 0
to 255 seconds. | column | seconds Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.25 |
| adsl2LConfProfL2Time This minimum time (in seconds) between an Entry into the
L2 state and the first Power Trim in the L2 state and between
two consecutive Power Trims in the L2 State.
It ranges from … | column | seconds Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.26 |
| adsl2LConfProfL2Atpr The maximum aggregate transmit power reduction (in dB) that
can be performed at transition of L0 to L2 state or through a
single Power Trim in the L2 state.
It ranges from 0 dB to… | column | dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.27 |
| adsl2LConfProfL2Atprt The total maximum aggregate transmit power reduction
(in dB) that can be performed in an L2 state. This is the
sum of all reductions of L2 Request (i.e., at transition of
L0 to L… | column | dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.28 |
| adsl2LConfProfRowStatus This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'activ… | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.10.238.1.5.1.2.1.29 |
| adsl2LConfProfScMaskUs Sub-carriers mask. A bitmap of 64 bits that allows masking
up to 64 downstream sub-carriers, depending on NSCds. If
bit i (0 <= i < NSCus) is set to '1', the respective
upstream… | column | ADSL2-LINE-TC-MIBAdsl2ScMaskUs | .1.3.6.1.2.1.10.238.1.5.1.2.1.3 |
| adsl2LConfProfRaModeDs The mode of operation of a rate-adaptive ATU-C in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2), or
dynamicRa(3). | column | ADSL2-LINE-TC-MIBAdsl2RaMode | .1.3.6.1.2.1.10.238.1.5.1.2.1.5 |
| adsl2LConfProfRaModeUs The mode of operation of a rate-adaptive ATU-R in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2), or
dynamicRa(3). | column | ADSL2-LINE-TC-MIBAdsl2RaMode | .1.3.6.1.2.1.10.238.1.5.1.2.1.6 |
| adsl2LConfProfRaUsNrmDs The Downstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for
… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.7 |
| adsl2LConfProfRaUsNrmUs The Upstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.8 |
| adsl2LConfProfRaUsTimeDs The Downstream Up-Shift Time Interval, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time that the downstream noise margin should sta… | column | seconds Unsigned32 | .1.3.6.1.2.1.10.238.1.5.1.2.1.9 |