configIpSubnetAutoStart
ACKSYS-MIB ·
.1.3.6.1.4.1.28097.8.1.1.1.14
Object
column
r/w
TriState
Define whether, after installation and initialization, the
subnet is activated immediately (when configuration is applied)
or only when a suitable event happens. See the 'L3 network
toggle' action in the Alarms/Events subsystem.
'Enable' sets the subnet initially 'up', 'Disable' sets it
initially 'down', 'Default' sets it initially 'up' except
if configIpAddressMode=none.
[FW:E2148.AC.1:4.12.0.1]
Context
- MIB
- ACKSYS-MIB
- OID
.1.3.6.1.4.1.28097.8.1.1.1.14- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- configIpSubnetEntry
- Table
- configIpSubnetTable
- Siblings
- 15
Syntax
TriState
- Source
- TriState
- Base type
Enumeration
Values & Constraints
Type Values
0 | default |
1 | disable |
2 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| configIpSubnetName Interface attached to this subnet | column | NetifName | .1.3.6.1.4.1.28097.8.1.1.1.1 |
| configIpSubnetFriendlyName Friendly name of this subnet | column | OctetString | .1.3.6.1.4.1.28097.8.1.1.1.10 |
| configIpSubnetBridgeEnable Write 2 (Enable) to configure this subnet as a bridge type
interface: create a bridge over specified interface(s) in this
subnet.
Write 1 (Disable) to configure thi… | column | DisableEnable | .1.3.6.1.4.1.28097.8.1.1.1.11 |
| configIpSubnetPersistence Define the behaviour of the IP layer when the lower interface
loses its connection.
- When enabled, the IP settings (IP addresses, routes through
this interface...) remain in pl… | column | TriState | .1.3.6.1.4.1.28097.8.1.1.1.12 |
| configIpSubnetEnable Set to Enable to install the layer 3 network. If disabled,
this subnet will not be initialized (thus not useable) after
the configuration is applied.
[FW:E2148.AC.1:4.12.0.1] | column | DisableEnable | .1.3.6.1.4.1.28097.8.1.1.1.13 |
| configIpSubnetPeerDns If this subnet is a DHCP client, should the DNS obtained from
the DHCP server replace the currently configured one?
Set to 'Enable' to give preference to the DHCP-p… | column | DisableEnable | .1.3.6.1.4.1.28097.8.1.1.1.15 |
| configIpSubnetDefaultRoute If this subnet is a DHCP client, should the server-provided
default route replace the currently configured one?
Set to 'Enable' to give preference to the DHCP serve… | column | DisableEnable | .1.3.6.1.4.1.28097.8.1.1.1.16 |
| configIpSubnetRowStatus row addition/deletion support
[net] | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.28097.8.1.1.1.2 |
| configIpAddressMode Ip address protocol of this subnet | column | Enumeration | .1.3.6.1.4.1.28097.8.1.1.1.3 |
| configIpSubnetIPv4Addr IPv4 address given to the interface | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.28097.8.1.1.1.4 |
| configIpSubnetIPv4Mask IPv4 subnet mask | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.28097.8.1.1.1.5 |
| configIpSubnetMetric Subnet metric | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.28097.8.1.1.1.6 |
| configIpSubnetDnsList Space-separated list of DNS IP addresses | column | OctetString | .1.3.6.1.4.1.28097.8.1.1.1.7 |
| configIpSubnetInterface Interface related to this ipSubnet. This field
must be left blank for bridge interfaces | column | OctetString | .1.3.6.1.4.1.28097.8.1.1.1.8 |
| configIpSubnetIPv4Gateway IPv4 gateway | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.28097.8.1.1.1.9 |