a3sysUblSource
A3Com-System-r8-MIB ·
.1.3.6.1.4.1.43.2.13.10.9.1.1
Object
column
mandatory
Enumeration
This identifies the entry number in this table.
Currently, the table is limited to two entries.
The first entry is labelled primary(1), the next
has the label secondary(2).
The NetBuilder RemoteOffice and NetBuilder II (as of
sw version 8.0) supports two additional entries.
Entry three (test) identifies a separate
boot block which is used when doing a test boot.
Entry four (dump) identifies where memory is to
be dumped. Note, only a subset of the columns in
this entry are relevant. Specifically, a3sysUblDevice
must have the value network(3) (ie, memory dumps are
preformed only over the network by the NBRO).
Context
- MIB
- A3Com-System-r8-MIB
- OID
.1.3.6.1.4.1.43.2.13.10.9.1.1- Type
- column
- Access
- readonly
- Status
- mandatory
- Parent
- a3sysUserBootListEntry
- Table
- a3sysUserBootListTable
- Siblings
- 26
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | primary |
2 | secondary |
3 | test |
4 | dump |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| a3sysUblConfigProt mandatory This object specifies the protocol to use
to get the configuration files if they
are stored across the network. Note, this
applies only if the value of
a3sysUblConfigFileDevice … | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.10 |
| a3sysUblConfigUserName mandatory This object indicates the Username to be
used by the file service protocol identified
the corresponding instance of a3sysUblConfigProt. | column | OctetString | .1.3.6.1.4.1.43.2.13.10.9.1.11 |
| a3sysUblConfigPassword mandatory This specifies the Password to be used
by the file service protocol identified by
the corresponding instance of a3sysUblConfigProt.
Note, for reasons of security, the value of thi… | column | OctetString | .1.3.6.1.4.1.43.2.13.10.9.1.12 |
| a3sysUblConfigAcct mandatory This specifies the Account Name used
by the file service protocol.
Note, for reasons of security, the value of this
object will be hidden. A string of 4 stars (*)
will be returne… | column | OctetString | .1.3.6.1.4.1.43.2.13.10.9.1.13 |
| a3sysUblMacAddress mandatory The MAC address to be used for booting over the
network. This can be configured to use either the
MAC address assigned to the CPU module or the MAC
address assigned to the I/O mo… | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.14 |
| a3sysUblCanonicalFlag mandatory This controls the format of addresses within
ARP packets sent by this system. | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.15 |
| a3sysUblRemoteProt mandatory This object specifies which serial link
protocol to use if a3sysUblSlot identifies
a slot with a High Speed Serial board.
If this is set to auto (4), the system
will try all sup… | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.16 |
| a3sysUblBaudRate mandatory This object specifies the serial line or
Token Ring baud rate. For all other types
of ports, this object will be ignored. | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.17 |
| a3sysUblClockSource mandatory This specifies whether to use an internal
or external clock source. This applies only
to High Speed Serial ports. | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.18 |
| a3sysUblConnectorType mandatory This object specifies the serial line
connector type. | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.19 |
| a3sysUblDevice mandatory This object identifies the source from which the
system attempts to boot. If this object is set to
localMediaA(1), the system will attempt to boot from
drive A of the local sto… | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.2 |
| a3sysUblWanAddress mandatory This specifies a string to initiate a
WAN connection. The specified string required
is interface and protocol specific. The maximum
string length is 80 bytes. Note, this appli… | column | OctetString | .1.3.6.1.4.1.43.2.13.10.9.1.20 |
| a3sysUblClientIpAddr mandatory The IP Address of this system used in packets
when booting over the network. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.43.2.13.10.9.1.21 |
| a3sysUblServerIpAddr mandatory The IP address of the Boot Server. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.43.2.13.10.9.1.22 |
| a3sysUblGwIpAddr mandatory The IP address of the gateway that will forward
packets to the Boot Server. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.43.2.13.10.9.1.23 |
| a3sysUblConfigFileIpAddr mandatory The IP address of the configuration files Server,
if needed. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.43.2.13.10.9.1.24 |
| a3sysUblIpMask mandatory The mask to be applied to the addresses specified
above. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.43.2.13.10.9.1.25 |
| a3sysUblAddressDiscovery mandatory This specifies the address discovery protocol
to use for booting from the network. If configAddr(3)
is specified, then the configured addresses are
used. If nothing has been spe… | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.26 |
| a3sysUblPassword mandatory This is needed when booting over a port that
uses a protocol that requires a password, e.g,
PPP. | column | OctetString | .1.3.6.1.4.1.43.2.13.10.9.1.27 |
| a3sysUblFileName mandatory This specifies the path and name of the boot
file. For example, to specify the file boot.29k in
the root directory, this object should
have the value 'boot.29k' | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.43.2.13.10.9.1.3 |
| a3sysUblNetFile obsolete This object has been deprecated. (use a3sysUblFileName
regardless of whether it's local or remote). | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.43.2.13.10.9.1.4 |
| a3sysUblSlot mandatory This specifies the physical slot where the IO module
from which the system will be booting is installed.
This only applies when a3sysUblDevice is set to
network(2) | column | Integer32 | .1.3.6.1.4.1.43.2.13.10.9.1.5 |
| a3sysUblInterface mandatory This specifies the physical port on the IO
module (installed in the slot identified by a3sysUblSlot)
that the system will be booting from. This only applies
when a3sysUblDevice … | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.6 |
| a3sysUblMaxRetries mandatory This object determines the number of times the
system will try to boot from the source identified
by this table entry before going to the next entry. | column | Integer32 | .1.3.6.1.4.1.43.2.13.10.9.1.7 |
| a3sysUblConfigFileDevice mandatory This specifies the device used to access the
configuration files needed by this system. If
this object has the value bootDevice(1), the
system will look for its configuration fil… | column | Enumeration | .1.3.6.1.4.1.43.2.13.10.9.1.8 |
| a3sysUblConfigFilePath mandatory This object specifies the path to the configuration
files needed by this system. | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.43.2.13.10.9.1.9 |