igmpSnoopQueryMaxResponseTime
A3COM0073IGMP-SNOOP ·
.1.3.6.1.4.1.43.10.37.1.5
Object
scalar
mandatory
r/w
Integer32
The maximum query response time in seconds advertised in IGMP v2 queries on this VLAN if the switch is the querier. Smaller values allow a switch to prune groups faster. So it is the maximum response time inserted into the general periodic queries. This variable enables the tuning of the burstiness of the IGMP traffic. If it is increased the responses have a larger time span in which to be generated by the hosts. It is set stack-wide. The default is 10 seconds and the range is 10 to 100 seconds. There could be 2 settings apart from the default. Slow Response (50 secs) and Very Slow Response (100 secs).
Context
- MIB
- A3COM0073IGMP-SNOOP
- OID
.1.3.6.1.4.1.43.10.37.1.5- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- igmpSnoop
- Siblings
- 10
Syntax
Integer32
Values & Constraints
Object Constraints
range: 10-100
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| igmpSnoopEnabled mandatory Enables/disables IGMP Snooping on this device. It is set stack-wide.
The defaule value is True. The range is True(1) or False(2). | scalar | TruthValue | .1.3.6.1.4.1.43.10.37.1.1 |
| igmpQueryEnabled mandatory Enabled/Disables IGMP Queries for this device.
The default value is True. The range is True(1) or False(2). | scalar | TruthValue | .1.3.6.1.4.1.43.10.37.1.10 |
| igmpQueryIpAddress mandatory This is the IP address used in IGMP Queries. The default value
is the management IP address. Since the root query device is
determined by the lowest IP address, you can vary th… | scalar | RFC1155-SMIIpAddress | .1.3.6.1.4.1.43.10.37.1.11 |
| igmpSnoopRobustness mandatory This enables IGMP tuning on a lossy network if a switch is the
querier. On such a network it may be increased. It is set stack-wide.
The default value is 1. The range is 1 to 2. … | scalar | Integer32 | .1.3.6.1.4.1.43.10.37.1.2 |
| igmpSnoopLeaveEnabled mandatory Enables/disables the processing of IGMP v2 leave messages stack-wide.
The default value is True(1). The range is True(1) or False(2). | scalar | TruthValue | .1.3.6.1.4.1.43.10.37.1.3 |
| igmpSnoopQueryTimeout mandatory The frequency at which IGMP general query packets are
transmitted on this VLAN by the querying switch in seconds.
So this is the time between general periodic queries being
sent o… | scalar | Integer32 | .1.3.6.1.4.1.43.10.37.1.4 |
| igmpSnoopLastMemberQueryTimeout mandatory A timeout interval in seconds. Maximum response time inserted
into the IGMP group specific queries sent in response to an
IGMP Leave by a querying switch. It is also the time bet… | scalar | Integer32 | .1.3.6.1.4.1.43.10.37.1.6 |
| igmpSnoopLastMemberQueryCount mandatory The number of group specific queries sent before the querying switch
decides that there are no more hosts listening to a particular group
multicast address. It is set stack-wide.
… | scalar | Integer32 | .1.3.6.1.4.1.43.10.37.1.7 |
| igmpSnoopRouterPortRefreshTimeout mandatory A timeout interval in seconds. The maximum time that
should elapse between multicast
router protocol PDUs on a port in the VLAN.
The default is 100 seconds and the range is from 7… | scalar | Integer32 | .1.3.6.1.4.1.43.10.37.1.8 |
| igmpSnoopVLANTable mandatory The (conceptual) table listing the VLANs on which IGMP
Snooping is enabled. | table | - | .1.3.6.1.4.1.43.10.37.1.9 |