h3cBfdSessAppSupportId
A3COM-HUAWEI-BFD-STD-MIB ·
.1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.3
Object
column
Bits
This variable contains an ID used to indicate a local application which owns or maintains this BFD session. Note, a BFD session can support several route protocols. This is a bit-map of possible conditions. The corresponding bit positions are: |0 |none | |1 |ospf | |2 |isis | |3 |bgp | |4 |mpls |
Context
- MIB
- A3COM-HUAWEI-BFD-STD-MIB
- OID
.1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.3- Type
- column
- Access
- readonly
- Status
- current
- Parent
- h3cBfdSessEntry
- Table
- h3cBfdSessTable
- Siblings
- 14
Syntax
Bits
Values & Constraints
Enumerated Values
0 | none |
1 | ospf |
2 | isis |
3 | bgp |
4 | mpls |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| h3cBfdSessIfIndex This variable contains an interface's index under which the BFD
session runs. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.1 |
| h3cBfdSessRemoteAddr This variable defines IP address of the remote interface
from which the BFD packets is transmitted.
It can also be used to enabled BFD on a specific
interface. The value is set to… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.10 |
| h3cBfdSessLocalDiag The BFD diagnostic code for the BFD session was down with the
neighbor. If no such event happens this object contains a zero
value. | column | BfdDiag | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.11 |
| h3cBfdSessState The state of the running BFD session.
There are three states through which a session normally
proceeds, two for establishing a session (Init and Up)
and one for t… | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.12 |
| h3cBfdSessControlPlanIndepFlag This variable indicates whether the local system
can continue to work while the control plane is out
of work. Specifically, it is set to true(1) if the
local system is independe… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.13 |
| h3cBfdSessAuthFlag This variable indicates that the local system wants
to use Authentication. Specifically, it is set
to true(1) if the local system wishes the session
to be authenticated or false(0… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.14 |
| h3cBfdSessDemandModeFlag This variable indicates that the local system wants
to use Demand mode. Specifically, it is set
to true(1) if the local system wishes to use
Demand mode or false(0) if not | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.15 |
| h3cBfdSessIndex This variable contains an index which represents a
unique BFD session on this device. | column | BfdSessIndexTC | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.2 |
| h3cBfdSessLocalDiscr This variable defines the local discriminator for this BFD
session, used to uniquely identify it. | column | Unsigned32 | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.4 |
| h3cBfdSessRemoteDiscr This variable defines the session discriminator chosen
by the remote system for this BFD session. | column | Unsigned32 | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.5 |
| h3cBfdSessDstPort The UDP Port for BFD. The default value is the
well-known value for this port. | column | INET-ADDRESS-MIBInetPortNumber | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.6 |
| h3cBfdSessOperMode This variable defines current operating mode that BFD
session is running in.
The primary mode which the BFD session runs in is known as
Asynchronous mo… | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.7 |
| h3cBfdSessAddrType This object defines IP address type of the interface
associated with this BFD session.
Only values unknown(0), ipv4(1) or ipv6(2)
have to be supported.
… | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.8 |
| h3cBfdSessLocalAddr This variable defines IP address of the local interface
from which the BFD packets is transmitted.
It can also be used to enabled BFD on a specific
interface. The value is set to … | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.43.45.1.10.2.72.1.3.1.9 |