SL-XPDR-MIB Table View

The connection table contains for each
transponding connection a single bi-directional entry.
The index to the table is the ifIndex of both XPDR interfaces.
The ifType valued used for the index is: 196.

xpdrConnConfigEntry row .1.3.6.1.4.1.4515.1.8.1.1.1

An entry in the transponding connection table.

Indexes

xpdrConnConfigIf1 xpdrConnConfigIf2

Column	Syntax	OID
xpdrConnConfigIf1 The first XPDR interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4515.1.8.1.1.1.1
xpdrConnConfigIf2 The second XPDR interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4515.1.8.1.1.1.2
xpdrConnConfigRateControlAdmin This variable ask the rate of the traffic used by this interface. Frequency is in Kbp/s. The value 0-30 is used for rate control Bypass.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.1.1.3
xpdrConnConfigRateControlOper This variable tells the rate of the traffic used by this interface. Frequency is in Kbp/s. The value 0 returned for rate control Bypass.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.1.1.4
xpdrConnConfigLosPropagation This object is used to detrmine if the LOS propagation should be active.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4515.1.8.1.1.1.5
xpdrServiceType The service type of the transponder.	XpdrServiceTyper/w Type Values: 1 ds3Sts1 2 fe 3 escon 4 dvbVideo 5 fc1gFicon 6 gbE 7 fc2g 8 oc3Stm1 9 oc12Stm4 10 oc48Stm16 11 other 12 fc4g 13 infiniband25G 14 otn27g 15 oc24gpon 16 smpteSdi 17 copperFe 18 copperGbe 19 mux2GbE 20 mux4GbE 21 xpdr5G 22 ficon1g 23 ficon2g 24 stm1 25 stm4 26 stm16 27 gpon248 28 ficon4g 29 eth10m 30 xfp10oc192 31 xfp10stm64 32 xfp10GbEWan 33 xfp10GbELan 34 xfp10otu2 35 xfp10GFC 36 xfp10GbEWanStm64 37 mux1GbE 38 mux1GbERegen 39 mux2GbERegen 40 mux4GbERegen 41 fc8g 42 ficon8g 43 mux10GbE 44 syncEgbE 50 otu1e 51 otu2e 52 otu1f 53 otu2f 54 oc192ToOtu2 55 stm64ToOtu2 56 gbe10WanToOtu2 57 gbe10LanToOtu2A 58 gbe10LanToOtu1e 59 gbe10LanToOtu2e 60 gbe10LanToOtu2B 61 fc10LanToOtu1f 62 fc10LanToOtu2f 63 fc8LanToOtu2 64 otu3 65 oc768 66 stm256 67 otu4 68 gbe40lan 69 gbe100lan 70 fc16g 71 smpteHdSdi 72 smpteSdSdi 73 smpte3gSdi 74 smpte3dSdi 75 smpteHdSdiNtsc 76 smpte3gSdiNtsc 77 fc16gNoIsl 81 cpri1 82 cpri2 83 cpri3 84 cpri4 85 cpri5 86 cpri6 87 cpri7 91 enc10GbELan 92 enc1GbELan 93 encfc1g 94 encfc2g 95 encfc4g 96 encfc8g 97 encfc16g 98 encfc10g 170 copper10m 171 copper10mAn 1701 copperFeAn	.1.3.6.1.4.1.4515.1.8.1.1.1.6
xpdrConnAddMask This object is a bit mask relevant only for Muxponder entry. It contains a bit for each Muxponder service. To add a service the management should set the corresponding bit to 1. To remove a service the bit should be se…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.1.1.7
xpdrMuxInbandAdmin This object is relevant only for muxponder. up value means that the muxponder inband management is enabled.	Enumerationr/w Enumerated Values: 1 up 2 down 3 standby	.1.3.6.1.4.1.4515.1.8.1.1.1.8
xpdrMuxInbandOper The operational state of the inband interface.	Enumeration Enumerated Values: 1 up 2 down 3 standby	.1.3.6.1.4.1.4515.1.8.1.1.1.9
xpdrDirection This object is used for unidirectional services. The upper port is the uplink as with the aps configuration. The transponder on one side should be configured as TX and the peer as RX.	Enumerationr/w Enumerated Values: 1 bidirectional 2 unidirectionalTx 3 unidirectionalRx 4 loopback	.1.3.6.1.4.1.4515.1.8.1.1.1.10
xpdrConnConfigCpriRateControl This object is used to detrmine if the CPRI rate control should be active.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4515.1.8.1.1.1.11
xpdrFaultPropagationDelay This object is used to determine the fault propagation delay. The value 0 mean no delay, the value 1 means 100ms delay, the value 2 means 200ms delay etc. 0 is the default value.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.1.1.12
xpdrFecMode This object is used to determine the IEEE FEC mode for 10G and 16G services: 0 - No FEC (default) 1 - FEC Monitoring 2 - FEC Generation 3 - FEC Regeneration	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.1.1.13

Description:
1. The port numbers are:
	0       unassigned 
	1..10   ODUs of Uplink 1
	11..20  ODUs of Uplink 2 (not available without 20G or 1+1 license)
2. All connections are unidirectional
3. P1 is the Source port and P2 is the Sync port
4. Port 0 is used as P2 when P1 is dropped
5. Port 0 is used as P1 when P2 is added
6. In the case of APS the two mate ODUs will apear with oduXcConnConfigProtected=TRUE
7. The allocation of ODUs per service port is described in xpdrConnAddMask above

oduXcConnConfigEntry row .1.3.6.1.4.1.4515.1.8.1.2.1

An entry in the ODU connection table.
An entry describes uni-directional connection of traffic from P1 (Source port) to port P2 (Sync port).

Indexes

oduXcConnConfigP1 oduXcConnConfigP2

Column	Syntax	OID
oduXcConnConfigP1 The Source port.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.2.1.1
oduXcConnConfigP2 The Sync port.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4515.1.8.1.2.1.2
oduXcConnConfigProtected Indication for entry with Protection Mates	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4515.1.8.1.2.1.3
oduXcConnConfigRowStatus The Status of this connection entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4515.1.8.1.2.1.4