DIFF-SERV-MIB Table View

The 'Aggregate' Table  enumerates Behavior Aggregate
classifiers (DSCPs) that a system may identify traffic
using.

diffServAggregateEntry row .1.3.6.1.4.1.9.6.1.101.51.1.2.1.1

An 'aggregate' entry describes a single BA
classifier.

Indexes

diffServAggregateDSCP

Column	Syntax	OID
diffServAggregateDSCP This is the Differentiated Services Code Point (DSCP) for the classifier. This object is only meant to be pointed to by a RowPointer from other tables, such as the diffServClassifierMatchObject, and is not actually conf…	Dscp Type Constraints: range: 0..63	.1.3.6.1.4.1.9.6.1.101.51.1.2.1.1.1

A table of MF  (IP 6-tuple multi-field) classifier
entries that a system may use to identify traffic.

diffServMFClassifierEntry row .1.3.6.1.4.1.9.6.1.101.51.1.2.2.1

A multi-field classifier entry describes a single MF
classifier.

Indexes

diffServMFClassifierIndex

Column	Syntax	OID
diffServMFClassifierIndex This is a unique index for the classifier. This object is meant to be pointed to by a RowPointer from other tables, such as the diffServClassifierMatchObject.	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.1
diffServMFClassifierAddrType The type of IP address used by this classifier entry.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.2
diffServMFClassifierDstAddr The IP address to match against the packet's destination IP address.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.3
diffServMFClassifierDstAddrMask A mask for the matching of the destination IP address. A zero bit in the mask means that the corresponding bit in the address always matches.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.4
diffServMFClassifierSrcAddr The IP address to match against the source IP address of each packet.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.5
diffServMFClassifierSrcAddrMask A mask for the matching of the source IP address.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.6
diffServMFClassifierDscp The value that the DSCP in the packet must have to match this entry. A value of -1 indicates that a specific DSCP value has not been defined and thus all DSCP values are considered a match.	Integer32r/w Constraints: range: -1-63	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.7
diffServMFClassifierProtocol The IP protocol to match against the IPv4 protocol number in the packet. A value of zero means match all.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.8
diffServMFClassifierDstL4PortMin The minimum value that the layer-4 destination port number in the packet must have in order to match this classifier entry.	MFClassifierL4Portr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.9
diffServMFClassifierDstL4PortMax The maximum value that the layer-4 destination port number in the packet must have in order to match this classifier entry. This value must be equal to or greater that the value specified for this entry in diffServMFCla…	MFClassifierL4Portr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.10
diffServMFClassifierSrcL4PortMin The minimum value that the layer-4 source port number in the packet must have in order to match this classifier entry.	MFClassifierL4Portr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.11
diffServMFClassifierSrcL4PortMax The maximum value that the layer-4 source port number in the packet must have in oder to match this classifier entry. This value must be equal to or greater that the value specified for this entry in dsSixTupleIpSrcL4Po…	MFClassifierL4Portr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.12
diffServMFClassifierStatus This indicates the status of this classifier entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.6.1.101.51.1.2.2.1.13

The classifier table enumerates specific classifiers
that a system may apply, including Differentiated
Services Code Points (DSCPs) and Multi-field
discriminators such as {Source IP Address, Destination
IP Address, IP Protocol, Source TCP/UDP Port,
Destination TCP/UDP Port).

diffServClassifierEntry row .1.3.6.1.4.1.9.6.1.101.51.1.2.3.1

An entry in the classifier table describes a single
classifier.

Indexes

IF-MIBifIndex diffServInterfaceDirection diffServClassifierNumber

Column	Syntax	OID
diffServInterfaceDirection Specifies the direction for this entry on the interface. 'inbound' traffic is operated on during receipt, while 'outbound' traffic is operated on prior to transmission.	Enumerationr/w Enumerated Values: 1 inbound 2 outbound	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.1
diffServClassifierNumber diffServClassifierNumber enumerates the classifier entry.	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.2
diffServClassifierMatchObject A pointer to the row that describes the applicable classifier. An obvious choice would be the diffServAggregateEntry for a given DSCP, but other choices include tables describing any classifier that may be of interest. …	SNMPv2-TCRowPointerr/w Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.3
diffServClassifierNext The 'next' variable selects the appropriate meter or action to apply to this class of traffic.	SNMPv2-TCRowPointerr/w Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.4
diffServClassifierSequence The sequence in which classifiers are applied, in ascending order. Classifiers with the same sequence number must be unambiguous. Classifiers with different sequence numbers may overlap in their ranges, with the under…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.5
diffServClassifierConfigType Used to indicate how the classifer is configured.	Enumerationr/w Enumerated Values: 0 other 1 mib 2 pib 3 bgp	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.6
diffServClassifierConfigTypeInfo Additional information associated with how the classifier is configured.	OctetStringr/w	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.7
diffServClassifierStatus The RowStatus variable controls the activation, deactivation, or deletion of a classifier. Any writable variable may be modified whether the row is active or notInService.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.6.1.101.51.1.2.3.1.8

The Meter Table enumerates specific token bucket
meters that a system may use to police a stream of
classified traffic. Such a stream may include a single
micro-flow, all traffic from a given source to a given
destination, all traffic conforming to a single
classifier, or any other cut of the traffic, including
all of it.
Note that the conceptual model requires all traffic to
pass through one or more meters, and that the last
meter configured in such a sequence must always
conform.
Counters in this table start counting on creation of
the meter that specifies their existence.

diffServTBMeterEntry row .1.3.6.1.4.1.9.6.1.101.51.1.2.4.1

An entry in the meter table describes a single token
bucket meter. Note that a meter has exactly one rate,
defined as the burst size each time interval. Multiple
meters may be cascaded should a multi-rate token bucket
…

Indexes

IF-MIBifIndex diffServInterfaceDirection diffServTBMeterNumber

Column	Syntax	OID
diffServTBMeterNumber The number of the meter, for reference from the classifier or in cascade from another meter.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.6.1.101.51.1.2.4.1.1
diffServTBMeterInterval The number of microseconds in the token bucket interval for this meter. Note that implementations frequently do not keep time in microseconds internally, so in implementation the effect of this value must be approximat…	microsecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.4.1.2
diffServTBMeterBurstSize The number of bytes in a single transmission burst. The rate at which the metered traffic may run is one burst per interval. Note that if multiple meters are cascaded onto one PHB, such as in AF, their intervals must b…	bytesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.4.1.3
diffServTBMeterFailNext If the traffic does not conform to the meter, the next meter or action to enquire of.	SNMPv2-TCRowPointerr/w Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.9.6.1.101.51.1.2.4.1.4
diffServTBMeterSucceedNext The 'Succeed Next' pointer selects which action or queue on the interface that to be used with the message. Incoming traffic may use the value zeroDotZero in this variable to indicate that no queuing on receipt occurs. …	SNMPv2-TCRowPointerr/w Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.9.6.1.101.51.1.2.4.1.5
diffServTBMeterStatus The RowStatus variable controls the activation, deactivation, or deletion of a meter. Any writable variable may be modified whether the row is active or notInService.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.6.1.101.51.1.2.4.1.6

The Action Table enumerates specific apply to  a stream
of classified traffic. Such a stream may include a
single micro-flow, all traffic from a given source to a
given destination, all traffic conforming to a single
classifier, or any other cut of the traffic, including
all of it.
Counters in this table start counting on creation of
the action that specifies their existence.

diffServActionEntry row .1.3.6.1.4.1.9.6.1.101.51.1.2.5.1

An entry in the action table describes the actions
applied to traffic conforming to a given meter.

Indexes

IF-MIBifIndex diffServInterfaceDirection diffServActionNumber

Column	Syntax	OID
diffServActionNumber The number of the meter, for reference from the classifier or in cascade from another meter.	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.1
diffServActionNext The 'Next' pointer selects which queue or Traffic Control Block on the interface. Incoming traffic may use the value zeroDotZero in this variable to indicate that no queuing on receipt occurs. Incoming interfaces genera…	SNMPv2-TCRowPointerr/w Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.2
diffServActionDSCP The DSCP that traffic conforming to this classifier and this meter is remarked with. Note that if the classifier is working from the same DSCP value, no effective change in the DSCP results. Differentiated Services may…	Dscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.3
diffServActionMinThreshold The min-threshold is the queue depth that a random drop process will seek to manage the queue's depth to. This object is in the action table rather than the queue table because Differentiated Services PHBs, such as the …	packetsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.4
diffServActionMaxThreshold The max-threshold is the maximum permissible queue depth. In tail drop scenarios, the queue will drop if a packet is presented to it and it is instantaneously full by this measure. In random drop scenarios, the queue wi…	packetsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.5
diffServActionDropPolicy The drop policy applied to traffic.	Enumerationr/w Enumerated Values: 1 other 2 alwaysDrop 3 tailDrop 4 randomDrop	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.6
diffServActionHCConformingPackets The number of Packets conforming to this meter. This object is used on high speed interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as …	bytesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.7
diffServActionConformingPackets The number of Packets conforming to this meter. This object may be used on low speed interfaces, and represents the least significant 32 bits of diffServActionHCConformingPackets. Discontinuities in the value of this …	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.8
diffServActionHCConformingOctets The number of octets conforming to this meter. This object is used on high speed interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as i…	bytesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.9
diffServActionConformingOctets The number of octets conforming to this meter. This object may be used on low speed interfaces, and represents the least significant 32 bits of diffServActionHCConformingOctets. Discontinuities in the value of this co…	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.10
diffServActionTailDrops The number of packets conforming to this classifier and meter that have been dropped because either the meter always drops, or the queue's depth exceeds the max-threshold value. On high speed devices, this object impl…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.11
diffServActionHCTailDrops The number of packets conforming to this classifier and meter that have been dropped because either the meter always drops, or the queue's depth exceeds the max-threshold value. This object should be used on high spee…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.12
diffServActionRandomDrops The number of packets conforming to this classifier and meter that have been dropped by a random drop process because the queue is over-full. On high speed lines, this object reflects the least significant 32 bits of …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.13
diffServActionHCRandomDrops The number of packets conforming to this classifier and meter that have been dropped by a random drop process because the queue is over-full. This object is used on high speed lines. Discontinuities in the value of th…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.14
diffServActionStatus The RowStatus variable controls the activation, deactivation, or deletion of a meter. Any writable variable may be modified whether the row is active or notInService.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.6.1.101.51.1.2.5.1.15

The Queue Table enumerates the queues  on an interface.
Queues are used to store traffic during intervals when
the arrival rate exceeds the departure rate for a class
of traffic. Because some PHBs indicate that the use of
a priority queue may be advisable, each queue in this
system is seen as having a priority. Those queues that
share the same priority operate in what may externally
appear to be a Weighted Round Robin manner, and preempt
the traffic belonging to any lower priority. For this
reason, it is strongly urged that traffic placed into
prioritized queues be strongly policed to avoid traffic
lockout.
Queues in this table also have a minimum and a maximum
rate.  When a maximum rate is specified, the queue acts
as a shaper if it has sufficient traffic and capacity
is available.  If it is a minimum rate, then the weight
in the WRR is effectively set to this rate divided by
the sum of the rates of queues on the interface,
guaranteeing it at least that throughput rate. If it is
a maximum rate, the queue operates as a shaper. A
shaper potentially reduces the rate of traffic through
it to the indicated rate, and minimizes variations in
rate.

diffServQueueEntry row .1.3.6.1.4.1.9.6.1.101.51.1.2.6.1

An entry in the Queue Table describes a single FIFO
queue.

Indexes

IF-MIBifIndex diffServInterfaceDirection diffServQueueNumber

Column	Syntax	OID
diffServQueueNumber The number of the queue.	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.1
diffServQueueMinimumRate The rate of the queue, in kilobits per second (KBPS). This unit is chosen because interfaces exist at the time of this writing which exceed the number of bits per second which may be represented in a 32 bit number. If …	KBPSSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.2
diffServQueueMaximumRate The rate of the queue, in kilobits per second (KBPS). This unit is chosen because interfaces exist at the time of this writing which exceed the number of bits per second which may be represented in a 32 bit number. If …	KBPSSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.3
diffServQueuePriority The priority of the queue. If multiple queues exist on the same interface at the same priority, they are effectively given Weighted Round Robin service. If multiple priorities are configured on an interface, traffic wi…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.4
diffServQueueNextTCB The 'Next' pointer selects the successor TCB on the interface. Incoming traffic may use the value zeroDotZero in this variable to indicate that the packet is now to be routed; outbound traffic may use the same value to…	SNMPv2-TCRowPointerr/w Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.5
diffServQueueOccupancyWeight The amount, in the form of a factor, that the current, actual queue occupancy should influence the averaged queue occupancy. The averaged queue occupancy can be used for comparison to configured drop thresholds in RED…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.6
diffServQueueStatus The RowStatus variable controls the activation, deactivation, or deletion of a queue. Any writable variable may be modified whether the row is active or notInService.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.6.1.101.51.1.2.6.1.7