ZHONE-PHY-WTN-RADIO-MIB

        Module for radio provisioning and status.
    
Source file
ZHONE-PHY-WTN-RADIO-MIB
Last revised
Identity
zhonePhyWtnRadio
Base OID
1.3.6.1.4.1.5504.6.106
Net-SNMP examples using the zhone MIB directory Show commands

These commands use the standard Observium installation path and load the selected MIB variant before the RFC and Net-SNMP directories.

Translate the module identity
/usr/bin/snmptranslate -Pud -Ir -On -m 'ZHONE-PHY-WTN-RADIO-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'ZHONE-PHY-WTN-RADIO-MIB::zhonePhyWtnRadio'
Walk the MIB subtree
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHONE-PHY-WTN-RADIO-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHONE-PHY-WTN-RADIO-MIB::zhonePhyWtnRadio'
How SNMP, Net-SNMP, MIB paths, and variants work
Objects (48)
.1.3.6.1.4.1.5504.5.8.1
.1.3.6.1.4.1.5504.5.8.1.1
.1.3.6.1.4.1.5504.5.8.1.1.1
.1.3.6.1.4.1.5504.5.8.1.1.10
feetEnumeration
.1.3.6.1.4.1.5504.5.8.1.1.11
feetInteger32
.1.3.6.1.4.1.5504.5.8.1.1.12
dBInteger32
.1.3.6.1.4.1.5504.5.8.1.1.13
.1.3.6.1.4.1.5504.5.8.1.1.14
.1.3.6.1.4.1.5504.5.8.1.1.15
Enumeration
.1.3.6.1.4.1.5504.5.8.1.1.16
.1.3.6.1.4.1.5504.5.8.1.1.17
dBInteger32
.1.3.6.1.4.1.5504.5.8.1.1.18
.1.3.6.1.4.1.5504.5.8.1.1.2
.1.3.6.1.4.1.5504.5.8.1.1.3
.1.3.6.1.4.1.5504.5.8.1.1.4
.1.3.6.1.4.1.5504.5.8.1.1.5
.1.3.6.1.4.1.5504.5.8.1.1.6
Enumeration
.1.3.6.1.4.1.5504.5.8.1.1.7
.1.3.6.1.4.1.5504.5.8.1.1.8
.1.3.6.1.4.1.5504.5.8.1.1.9
.1.3.6.1.4.1.5504.5.8.2
.1.3.6.1.4.1.5504.5.8.2.1
Bits
.1.3.6.1.4.1.5504.5.8.2.1.1
.1.3.6.1.4.1.5504.5.8.2.1.2
Bits
.1.3.6.1.4.1.5504.5.8.2.1.3
.1.3.6.1.4.1.5504.5.8.2.1.4
.1.3.6.1.4.1.5504.5.8.2.1.5
.1.3.6.1.4.1.5504.5.8.2.1.6
.1.3.6.1.4.1.5504.5.8.3
.1.3.6.1.4.1.5504.5.8.3.1
.1.3.6.1.4.1.5504.5.8.3.1.1
.1.3.6.1.4.1.5504.5.8.3.1.2
.1.3.6.1.4.1.5504.5.8.4
.1.3.6.1.4.1.5504.5.8.4.1
dBmInteger32
.1.3.6.1.4.1.5504.5.8.4.1.1
dBmInteger32
.1.3.6.1.4.1.5504.5.8.4.1.2
.1.3.6.1.4.1.5504.5.8.4.1.3
.1.3.6.1.4.1.5504.5.8.4.1.4
.1.3.6.1.4.1.5504.5.8.5
.1.3.6.1.4.1.5504.5.8.5.0
Enumeration
.1.3.6.1.4.1.5504.5.8.5.1
Enumeration
.1.3.6.1.4.1.5504.5.8.5.2
.1.3.6.1.4.1.5504.5.8.6
.1.3.6.1.4.1.5504.5.8.6.1
.1.3.6.1.4.1.5504.5.8.6.1.1
.1.3.6.1.4.1.5504.5.8.6.1.2
.1.3.6.1.4.1.5504.5.8.6.1.3
.1.3.6.1.4.1.5504.6.106
Dependencies (10) 7 direct · 3 transitive Show tree and compile order Hide dependency details

Each imported module is resolved in the importing module's source directory first, then through the normal default-variant rules.

Dependency tree
Notifications / Traps (15)
NameOIDDescription
.1.3.6.1.4.1.5504.5.8.5.0.1
Critical indoor equipment failure trap.
Can be caused by:
power supply failure, watchdog timeout, or other internal
failure on indoor unit.
.1.3.6.1.4.1.5504.5.8.5.0.10
Spurious or intermittant ODU hardware failure trap.
Could be loss of reference signal from IDU or hardware error.
.1.3.6.1.4.1.5504.5.8.5.0.11
Significant deviation of ODU temperature from specified limits
May be power amp heating up or environment heat buildup, or
environment ice or frost.
.1.3.6.1.4.1.5504.5.8.5.0.12
Warning to indicate that ODU is approaching a significant
deviation of ODU temperature from specified limits.
May be power amp heating up or environment heat buildup, or
environment ice or frost.
.1.3.6.1.4.1.5504.5.8.5.0.13
Receive signal strength at the odu is lower (in dB) than wtnOduRxRSSIThresh.
This alarm will persist until the RSSI rises above wtnOduRxRSSIThresh - wtnOduRxRssiHysteresisWindow.

May be from signal path degradation.
May be power amp heating up or environment heat buildup.
.1.3.6.1.4.1.5504.5.8.5.0.14
Modem reports temporary BER > threshold alarm.
Condition is true when current BER > wtnMdmRxBERThresh.
Condition will persist until current BER < ( wtnMdmRxBERThresh - wtnMdmRxBERHysteresisWindow ).

Probable fade burst.
Could be interference.
Could be incipient hardware fault
.1.3.6.1.4.1.5504.5.8.5.0.15
Modem reports temporary post-detection signal to noise ratio
below preset threshold wtnMdmRxEbNoThresh.

This condition will persist until the radio signal quality
rises above wtnMdmRxEbNoThresh - wtnMdmRxEbnoHysteresisWindow.

Probable fade or noise burst.
.1.3.6.1.4.1.5504.5.8.5.0.2
Non-critical indoor equipment failure trap.
Can be caused by:
spurious power supply failure,
or other temporary internal failure on indoor unit.
.1.3.6.1.4.1.5504.5.8.5.0.3
Critical failure of IDU to ODU communications link trap.
can be caused by:
IDU/ODU cable failure,
bad connection, or
equipment failure.
.1.3.6.1.4.1.5504.5.8.5.0.4
Intermittent failure of IDU to ODU communications link trap.
can be caused by:
IDU/ODU cable failure,
bad connection,
or spurious equipment failure.
.1.3.6.1.4.1.5504.5.8.5.0.5
Permanent or persistant loss of lock of internal clocks
in indoor unit.
.1.3.6.1.4.1.5504.5.8.5.0.6
Spurious or intermittant loss of lock of internal
clocks in indoor unit.
.1.3.6.1.4.1.5504.5.8.5.0.7
Radio overhead channel failure trap. May be caused by
signal path degradation, or equipment failure on local or
far end node.
.1.3.6.1.4.1.5504.5.8.5.0.8
Spurious or intermittant radio overhead channel failure trap.
May be caused by signal path degradation
or equipment failure on local or
far end node.
.1.3.6.1.4.1.5504.5.8.5.0.9
Critical ODU hardware failure trap. Possible causes:
Synthesizer has lost desired frequency.
Could be loss of reference signal from IDU or hardware error.
Synthesizer hardware fault.
Possible component fault.