ZHONE-COM-PPP-MIB Table View

This table is used to configure attributes of a PPP
interface that are not currently covered by the
standard MIBs.  This table is indexed by the ifIndex
of the PPP interface.  IANA iftype ppp is #23.

pppInterfaceEntry row .1.3.6.1.4.1.5504.4.5.1.1

There is an entry in this table for every provisioned
PPP interface. Rows are created by setting pppIfRowStatus
to createAndGo(4). Rows are removed by setting
pppIfRowStatus to destroy(6). When a row is created or
de…

Indexes

IF-MIBifIndex

Column	Syntax	OID
pppIfLowerIfIndex The ifIndex of the lower layer interface to which this PPP interface should be bound. Since PPP interfaces are always statically bound, this value can never be zero. Upon setting this field, the ifStack will be modifie…	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.5504.4.5.1.1.1
pppIfVpi If this IP interface is on an ATM VC, the ATM VPI is specified here. If the IP interface is not an ATM VC, this field is ignored. The VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. For ATM U…	ATM-TC-MIBAtmVpIdentifierr/w Type Constraints: range: 0..4095	.1.3.6.1.4.1.5504.4.5.1.1.2
pppIfVci If this PPP interface is on an ATM VC, the ATM VCI is specified here. If the PPP interface is not an ATM VC, this field is ignored. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxActiveVciBits…	ATM-TC-MIBAtmVcIdentifierr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.5504.4.5.1.1.3
pppIfCallMode Indicates where the PPP call is initiated. noCall: No call is initiated inCall: Call is intiated remotely. outCall: Call is intiated locally.	Enumerationr/w Enumerated Values: 1 noCall 2 inCall 3 outCall	.1.3.6.1.4.1.5504.4.5.1.1.4
pppIfFrameType The type of framing used if the link type is ATM or Frame Relay. If link type is atm, pppIfFrameType must be atmLLC or atmVc. If link type is frameRelay, pppIfFrameType must be frameRelay. If link type …	Enumerationr/w Enumerated Values: 1 none 2 frameRelay 3 atmLLC 4 atmVc	.1.3.6.1.4.1.5504.4.5.1.1.5
pppIfNumChannels The maximum number of channels allowed on this interface. Currently, only one channel is supported.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.5504.4.5.1.1.6
pppIfRowStatus Zhone convention to support row creation and deletion. pppIfLgId is required to create or destroy a row in this table.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.5.1.1.7

This table is used to configure attributes not found
in the pppLinkConfigTable defined in RFC 1471.  This 
table is indexed by the ifIndex of the PPP interface
to which these LCP attributes apply.

pppLCPExtensionsEntry row .1.3.6.1.4.1.5504.4.5.2.1

There is an entry in this table for every provisioned PPP
interface. Rows in this table are created or deleted when
a row in the pppInterfaceTable is created or deleted using
pppIfRowStatus. Therefore, objects in t…

Indexes

No indexes recorded

Column	Syntax	OID
lcpExtReceiveAuthEnable Enable or disable incoming authentication.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.1
lcpExtReceiveAuthProtocol The preferred protocol used for incoming authentication. If lcpExtReceiveAuthEnable is enabled, the authentication protocol will be negotiated with the peer.	ZhoneAuthenticationProtocolr/w Type Values: 1 pap 2 chap	.1.3.6.1.4.1.5504.4.5.2.1.2
lcpExtSendAuthEnable Enable or disable outgoing authentication.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.3
lcpExtSendAuthProtocol The protocol used with lcpExtSendAuthIdentity to look up the outgoing authentication information.	ZhoneAuthenticationProtocolr/w Type Values: 1 pap 2 chap	.1.3.6.1.4.1.5504.4.5.2.1.4
lcpExtSendAuthIdentity The identity (PAP peer ID or CHAP name) used with lcpExtSendAuthProtocol to look up the outgoing authentication information. Default value is the empty string.	OctetStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.5504.4.5.2.1.5
lcpExtQualityProtocol The Quality Protocol used. Currently, the only valid quality protocl is LQR. Quality protocol must be enabled using pppLqrConfigStatus in RFC1471.	Enumerationr/w Enumerated Values: 1 lqr	.1.3.6.1.4.1.5504.4.5.2.1.6
lcpExtMagicNumber The number used in Magic Number negotiation. Magic number negotiation must be enabled using pppLinkConfigMagicNumber in RFC1471. When set to zero, a random number will be used for the magic number. Thi…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.5.2.1.7
lcpExtMaxPad The number of padded bytes at the end of data. This is used for Self-Describing Padding, a method for placing unambiguous padding octets at the end of the PPP Information field in order to cause messages to fall on a n…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.5504.4.5.2.1.8
lcpExtCallbackEnable Enable or disable Callback negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.9
lcpExtCallbackType The method of determining the location to callback. byAuth: Location is determined by authorization information. byDialString: Location is determined by a dialing string. byIdentifier: Location i…	Enumerationr/w Enumerated Values: 1 byAuth 2 byDialStr 3 byIdentifier 4 byE164 5 byName	.1.3.6.1.4.1.5504.4.5.2.1.10
lcpExtCallbackDialString The dialing string used for a callback. The format of this string is determined by lcpExtCallbackType. This object only applies when callback negotiation is enabled using lcpExtCallbackEnable. …	OctetStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.5504.4.5.2.1.11
lcpExtRestartTimer Number of seconds before retransmission of an LCP packet.	secondsInteger32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.2.1.12
lcpExtMaxConfigRetries Number of LCP configuration retries without response before the link is brought down.	Integer32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.2.1.13
lcpExtMaxTerminateRetries Number of LCP termination retries without response before the link is brought down.	Integer32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.2.1.14
lcpExtMaxFailureRetries Number of times a Configuration Nak is sent before a Configuration Rej is sent.	Integer32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.2.1.15
lcpExtMRUEnable Enable or disable MRU negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.16
lcpExtACCMEnable Enable or disable Asynchronous Control Character Map negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.17
lcpExtPFCEnable Enable or disable Protocol Field Compression negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.18
lcpExtACFCEnable Enable or disable Address and Control Field Compression negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.19
lcpExtFCSAltEnable Enable or disable FCS Alternative negotiation. The negotiated FCS values take effect only during Authentication and Network-Layer Protocol phases.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.20
lcpExtSDPEnable Enable or disable Self-Describing Padding negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.21
lcpExtNumModeEnable Enable or disable Numbered Mode negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.2.1.22

This table is used to configure attributes not found
in the pppIpConfigTable defined in RFC 1473.  This 
table is indexed by the ifIndex of the network (IP) interface
to which these NCP attributes apply.

pppNCPExtensionsEntry row .1.3.6.1.4.1.5504.4.5.3.1

A row must be created in this table when an IP over PPP
interface is provisioned. Rows are created by setting
ipIfPppEnabled in the ipInterfaceTable to 'true'.
Rows are deleted by setting ipIfPppEnabled in the ipInt…

Indexes

IF-MIBifIndex

Column	Syntax	OID
ncpExtVJCompMaxSlotID The maximum slot ID for Van Jacobson Header Compression.	Integer32r/w Constraints: range: 3-16	.1.3.6.1.4.1.5504.4.5.3.1.1
ncpExtVJCompSlotID Indicates whether the slot identifier field may be compressed: disabled: The slot identifier must not be compressed. All compressed TCP packets must set the C bit in every change m…	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.3.1.2
ncpExtIpAddrOptionEnable Enable or disable IP Address Negotiation.	EnableFlagr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.5504.4.5.3.1.3
ncpExtRestartTimer Number of seconds before retransmission of an IP packet.	secondsInteger32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.3.1.4
ncpExtMaxConfigRetries Number of IP configuration retries without response before the session is brought down.	Integer32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.3.1.5
ncpExtMaxTerminateRetries Number of IP termination retries without response before the session is brought down.	Integer32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.3.1.6
ncpExtFailureRetries Number of times a Configuration Nak is sent before a Configuration Rej is sent	Integer32r/w Constraints: range: 1-999	.1.3.6.1.4.1.5504.4.5.3.1.7

This table contains provisioning for incoming and/or
outgoing PPP authentication.

pppAuthenticationEntry row .1.3.6.1.4.1.5504.4.5.5.1

An entry exists in the pppAuthenticationTable for each set
of data used for PPP authentication. A set of PPP
authentication data can be used for incoming authentication,
outgoing authentication or both. A row can be cr…

Indexes

pppAuthSubId pppAuthId

Column	Syntax	OID
pppAuthSubId The unique identifier of the subscriber associated with this authentication entry. A single subscriber may have multiple authenticated users. If this entry is only used for outgoing authentication, there may not be …	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.5.5.1.1
pppAuthId A unique number used to identify this authentication entry.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.5504.4.5.5.1.2
pppAuthIpIfIndex The ifIndex of the IP record associated with this set of PPP authentication data. If this entry is to be used for incoming authentication, this object must be set to a non-zero value.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.5504.4.5.5.1.3
pppAuthLgId The unique identifier of the line group on which this authentication data is allowed to be used. If the value is zero, this authentication data can be used on any line group.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.5504.4.5.5.1.4
pppAuthProtocol The protocol used for authentication: PAP - Password Authentication Protocol CHAP - Challenge Handshake Authentication Protocol A bit is set for each authentication protocol that is enabled. …	Bitsr/w Enumerated Values: 0 pap 1 chap	.1.3.6.1.4.1.5504.4.5.5.1.5
pppAuthPAPPeerID The username used if we are authenticating with the PAP protocol. Default value is the empty string.	OctetStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.5504.4.5.5.1.6
pppAuthPAPPassword The password used if we are authenticating with the PAP protocol. Default value is the empty string. For security, an empty string will be returned on a GET.	OctetStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.5504.4.5.5.1.7
pppAuthCHAPName The username used if we are authenticating with the CHAP protocol. Default value is the empty string.	OctetStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.5504.4.5.5.1.8
pppAuthCHAPSecret The password used if we are authenticating with the CHAP protocol. Default value is the empty string. For security, an empty string will be returned on a GET.	OctetStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.5504.4.5.5.1.9
pppAuthStatus Setting this object to 'invalid' causes the information for that entry to become invalidated. Calls using the authentication information from an invalidated entry will not be accepted or initiated. This allows an entr…	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.5504.4.5.5.1.10
pppAuthRowStatus This object is used to create or delete an entry in the table. Setting this object to 'createAndGo' will cause an entry to be created. Setting this object to 'destroy' will cause an entry to be deleted. Objects requi…	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.5.5.1.12