ZHONE-COM-BRIDGE-REC-MIB Table View

This table contains information required for the management
of bridge interfaces.

bridgeInterfaceEntry row .1.3.6.1.4.1.5504.4.7.2.1

An entry exists for each bridge interface in the system.
At a mininum the ifIndex must be present to create a row.

Indexes

IF-MIBifIndex

Column	Syntax	OID
bridgeIfVpi If this bridge interface is on an ATM VC, the ATM VPI is specified here. If the bridge interface is not an ATM VC, this field is ignored. The VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. …	ATM-TC-MIBAtmVpIdentifierr/w Type Constraints: range: 0..4095	.1.3.6.1.4.1.5504.4.7.2.1.1
bridgeIfVci If this bridge interface is on an ATM VC, the ATM VCI is specified here. The range is 32...65535. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. I…	ATM-TC-MIBAtmVcIdentifierr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.5504.4.7.2.1.2
bridgeIfVlanId The Virtual LAN Id for VLAN Tag Insertion.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.7.2.1.3
bridgeIfStripAndInsert If true, enable VLAN Tagging.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.4
bridgeIfCustomARP If true, send ARP requests selectively or by flood.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.5
bridgeIfFilterBroadcast If true, discard non-ARP broadcast packets.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.6
bridgeIfLearnIp If true, snoop unicast packets to build ARP table.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.7
bridgeIfLearnUnicast If true, snoop unicast packets to build MAC paths.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.8
bridgeIfMaxUnicast Maximum number of unicast addresses for I/F.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.7.2.1.9
bridgeIfLearnMulticast If true, snoop multicast packets for IGMP joins/leaves.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.10
bridgeIfForwardToUnicast If true, attempt to forward via unicast MAC paths.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.11
bridgeIfForwardToMulticast If true, attempt to forward via multicast MAC paths.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.12
bridgeIfForwardToDefault If true, attempt to forward via VLAN default paths.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.13
bridgeLowerIfIndex An entry exists for each bridge interface in the system. Only Ifindex and lower if index is needed to create a row.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.5504.4.7.2.1.14
bridgeIfRowStatus This object is used to create and remove rows in the table. See bridgeInterfaceEntry description for minimum requirements.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.2.1.15
bridgeIfCustomDHCP If TRUE, forwards broadcast DHCPOFFER or DHCPACK packets even if bridgeFilterBroadcast is TRUE for that interface.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.16
bridgeIfIngressPacketRuleGroupIndex Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the ingress interface.	PacketRuleGroupIndexr/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.5504.4.7.2.1.17
bridgeIfVlanIdCOS The Class-Of-Service (COS) value used for VLAN Tag Insertion.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.5504.4.7.2.1.18
bridgeIfOutgoingCOSOption Determines COS setting on packets bridged out this interface. disable - COS setting is untouched. all - COS will be set to bridgeIfOutgoingCOSValue.	Enumerationr/w Enumerated Values: 1 outgoingCOSOptionDisable 2 outgoingCOSOptionAll	.1.3.6.1.4.1.5504.4.7.2.1.19
bridgeIfOutgoingCOSValue The COS value loaded into outgoing tagged packets. Applicable only if interface sends tagged packets and bridgeIfOutgoingCOSOption is outgoingCOSOption_all.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.5504.4.7.2.1.20
bridgeIfStagTPID The value of the tag protocol identifier that is being used for QinQ packets. (0x8100 is default.)	Integer32r/w Constraints: range: 33024-33024 range: 34984-34984 range: 37120-37120 range: 37376-37376	.1.3.6.1.4.1.5504.4.7.2.1.21
bridgeIfStagId The s-tag value that we are expecting to put on packets that are Rxed on this interface.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.5504.4.7.2.1.22
bridgeIfStagStripAndInsert If true, enable S-tag tagging on this IF.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.23
bridgeIfStagOutgoingCOSOption Determines s-tag COS settings on packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s_tagOutgoingCOSValue.	Enumerationr/w Enumerated Values: 1 sTagCOSDisable 2 sTagCOSAll	.1.3.6.1.4.1.5504.4.7.2.1.24
bridgeIfStagCOS The s-tag COS to be used when doing s-tag insertion.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.5504.4.7.2.1.25
bridgeIfStagOutgoingCOSValue The s-tag COS value loaded into outgoing tagged packets. Applicaple only if interface sends S-tagged packets and s_tagOutgoingCOSOption is All.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.5504.4.7.2.1.26
bridgeIfMcastControlList List of mcast-control-ids this bridge-interface-record is associated with. It is an integer stored as string, and controls which channels a user can watch. Note: unlike for IP, an empty list here allows user to watch a…	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.2.1.27
bridgeIfMaxVideoStreams Maximum number of multicast (video) streams that we will support.	Unsigned32r/w Constraints: range: 0-1024	.1.3.6.1.4.1.5504.4.7.2.1.28
bridgeIfIsPPPoA If true, this interface accepts PPPoA packets and will bridge them out as PPPoE packets.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.29
bridgeIfFloodUnknown If true, flood frames with unknown unicast MAC address that would otherwise be discarded.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.30
bridgeIfFloodMulticast If true, flood all multicast traffic received on this bridge to all other ports on this vlan.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.31
bridgeIfEgressPacketRuleGroupIndex Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the egress interface.	PacketRuleGroupIndexr/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.5504.4.7.2.1.32
bridgeIfTableBasedFilter none : Dynamic IP Filtering on bridge based on DHCP, is disabled. BIT 1(mac) : MAC address based Filtering based on DHCP, is enabled. BIT 2(ip) : IP address based dynamic IP Filtering based on DHCP, …	Bitsr/w Enumerated Values: 0 mac 1 ip	.1.3.6.1.4.1.5504.4.7.2.1.33
bridgeIfDhcpLearn none :IP address and Mac address are not learned from DHCP packets. BIT 1 (mac): MAC addresses are learned from DHCP packets. ip 2 (ip) : IP addresses are learned from DHCP packets. The Defval is c…	Bitsr/w Enumerated Values: 0 mac 1 ip	.1.3.6.1.4.1.5504.4.7.2.1.34
bridgeIfOnDemandStatsEnabled If true, the on-demand stats collection for this bridge interface will be enabled and packets will be counted. If bytes, the on-demand stats collection for this bridge interface will be enabled and abd bytes will be co…	Enumerationr/w Enumerated Values: 1 true 2 false 3 bytes	.1.3.6.1.4.1.5504.4.7.2.1.35
bridgeIfMvrVlan The Multicast Vlan Registration (MVR) vlan ID. Multicast video packets with this vlan can be vlan translated out this bridge.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.5504.4.7.2.1.36
bridgeIfVlanXlateFrom If a packet's VLAN ID value matches this object's value then the packet's VLAN ID will be translated to the value of bridgeIfVlanId. A zero value disables translation.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.5504.4.7.2.1.37
bridgeIfSlanXlateFrom If a packet's SLAN ID value matches this object's value then the packet's SLAN ID will be translated to the value of bridgeIfStagId. A zero value disables translation.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.5504.4.7.2.1.38
bridgeIfBridgeState Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N…	BridgeStater/w Type Values: 1 up 2 down 3 trouble 4 notAvailable 5 initializing 6 adminDown 7 adminStateTest 8 adminStateNone 9 ready 10 discovering 11 unknown 12 blocked 13 pending 14 disabled 15 learning 16 forwarding 17 blockedFlapping 18 blockedPersistent 19 blockedFlappingPersistent	.1.3.6.1.4.1.5504.4.7.2.1.39
bridgeIfUnblock Set to TRUE to unblock a bridge that is blocked due to flapping.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.2.1.40
bridgeType bridge type	Enumerationr/w Enumerated Values: 1 uplink 2 downlink 4 intralink 6 tls 8 rlink 9 pppoa 10 wire 11 mvr 12 user 13 downlinkVideo 14 downlinkData 15 downlinkPPPoE 16 downlinkP2P 17 downlinkVoice 18 downlinkUpstreamMcast 19 ipobTls 20 ipobUplink 21 ipobDownlink	.1.3.6.1.4.1.5504.4.7.2.1.41
bridgeIfGponGemPortId GPON GEM Port ID used only to create a bridge on a GPON ONU.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.2.1.42
bridgeIfGponTrafficProfile GPON Traffic Profile Index used only to create a bridge on a GPON ONU.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.2.1.43
bridgeIfIncomingCOSOption Determines COS settings on incoming packets bridged out this interface: disable - COS replcement feature is disabled all - COS will be set with vlanIDCOS.	Enumerationr/w Enumerated Values: 1 incomingCOSOptionDisable 2 incomingCOSOptionAll	.1.3.6.1.4.1.5504.4.7.2.1.44
bridgeIfStagIncomingCOSOption Determines s-tag COS settings on incoming packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s-tagIdCOS.	Enumerationr/w Enumerated Values: 1 stagIncomingCOSOptionDisable 2 stagIncomingCOSOptionAll	.1.3.6.1.4.1.5504.4.7.2.1.45

A collection of staticBridgeEntries.

staticBridgeEntry row .1.3.6.1.4.1.5504.4.7.3.1

Static Bridge entries are created by the user in
order to specify forwarding for a particular
interface, vlanId, mac address or ip address,
slanId (for QinQ).

The INDEX value for staticBridgeEntry consists …

Indexes

IF-MIBifIndex staticBridgeAddressType bridgeIfVlanId staticBridgeMacOrIpAddress bridgeIfStagId

Column	Syntax	OID
staticBridgeMacOrIpAddress If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this field represents an IP address.	OctetString Constraints: range: 6-6	.1.3.6.1.4.1.5504.4.7.3.1.1
staticBridgeAddressType If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If stati…	Enumeration Enumerated Values: 1 macAddr 2 ipAddr 3 vlanIdAddr 4 globalAddr 7 intralinkAddr 8 globalIntralinkAddr 9 dhcpIpAddr 10 dhcpMacAddr 13 mvrAddr 14 vlanParms 15 secMvrAddr 720901 dhcpAllowOui	.1.3.6.1.4.1.5504.4.7.3.1.2
staticBridgeMulticastAging Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turn…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.7.3.1.3
staticBridgeRowStatus Used to create, modify or delete an entry in this table.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.3.1.4
staticBridgeFlapControl This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) turn flap control mode on. 'Enable(3)' applies a hold time…	Enumerationr/w Enumerated Values: 1 default 2 disable 3 enable 4 fast	.1.3.6.1.4.1.5504.4.7.3.1.5
staticBridgeUnicastAging Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turn…	Integer32r/w Constraints: range: 0-0 range: 120-2147483647	.1.3.6.1.4.1.5504.4.7.3.1.6
staticBridgeIgmpQueryInterval How often (in seconds) we as a bridge inject IGMP query values into the stream.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.3.1.7
staticBridgeFlags none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondToQuery) : igmpRes…	Bitsr/w Enumerated Values: 0 igmpProcessJoinAndLeave 1 igmpRespondToQuery 2 igmpUseBridgeIpAddress 3 forceIGMPv2Down 4 forceIGMPv2Up	.1.3.6.1.4.1.5504.4.7.3.1.8
staticBridgeIgmpCustomIpAddress Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.5504.4.7.3.1.9
staticBridgeLoopPrevention This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a learning bridge if it f…	Enumerationr/w Enumerated Values: 0 none 1 blockAsym 2 blockAll 3 blockAsymAuto 4 blockAllAuto	.1.3.6.1.4.1.5504.4.7.3.1.10
staticBridgeIgmpDscp This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (001010) …	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.5504.4.7.3.1.11

A collection of bridgeIfLookupTable entries.

bridgeIfLookupEntry row .1.3.6.1.4.1.5504.4.7.4.1

Bridge IfLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.

The INDEX value for bridgeIfLo…

Indexes

bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId IF-MIBifIndex bridgeIfStagId

Column	Syntax	OID
bridgeIfAddressType If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddre…	Enumeration Enumerated Values: 1 unicastMac 2 multicastMac 3 ipAddress 4 dhcpMac 5 dhcpIp 6 ipV6Address 7 dhcpV6Mac 8 dhcpV6Ip	.1.3.6.1.4.1.5504.4.7.4.1.1
bridgeIfMacOrIpAddress If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress represents a MAC Address. If bridgeIfAddressTy…	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.5504.4.7.4.1.2
bridgeIfLookupStaticOrDynamic If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.	Enumeration Enumerated Values: 1 staticEntry 2 dynamicEntry	.1.3.6.1.4.1.5504.4.7.4.1.3
bridgeIfLookupFlush The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of address type, MAC or IP address and vlan ID is used to deter…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.4.1.4

A collection of bridgeAddressLookupTable entries.

bridgeAddressLookupEntry row .1.3.6.1.4.1.5504.4.7.5.1

BridgeAddressLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.

The INDEX value for bridge…

Indexes

IF-MIBifIndex bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId bridgeIfStagId

Column	Syntax	OID
bridgeAddressLookupStaticOrDynamic If bridgeAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeAddressLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.	Enumeration Enumerated Values: 1 staticEntry 2 dynamicEntry	.1.3.6.1.4.1.5504.4.7.5.1.1
bridgeAddressLookupFlush The object 'bridgeIfAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used to determine which interface is to be removed. Setting the…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.5.1.2

A collection of entries each representing the next
available index for that group.

packetRuleGroupNextIndexEntry row .1.3.6.1.4.1.5504.4.7.6.2.1

A packetRuleGroupNextIndexEntry contains the next
available index for that packetRuleGroup.

Indexes

packetRuleGroupIndex

Column	Syntax	OID
packetRuleGroupMemberNextIndex The next index available in a given packetRuleGroup for a new packetRuleEntry.	PacketRuleGroupIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.5504.4.7.6.2.1.1

A collection of packetRuleEntries.

packetRuleEntry row .1.3.6.1.4.1.5504.4.7.6.3.1

Packet Rule entries are created by the user in
order to specify filtering or other packet manipulation
for a particular interface.

Indexes

packetRuleGroupIndex packetRuleGroupMemberIndex

Column	Syntax	OID
packetRuleGroupMemberIndex The index of a packetRuleEntry in a given packetRuleGroup.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.5504.4.7.6.3.1.1
packetRuleType A 32-bit value which determines a filter to be applied to packets on the interface matching the pattern specified in packetRuleValue. The size and offset of the pattern in the packet will depend on packetRuleType. …	Enumerationr/w Enumerated Values: 37 dstMacSwapStatic 38 dstMacSwapDynamic 41 dscpToCos 42 promoteFirstEncapsulationVlan 43 filterFirstEncapsulationVlan 44 promoteSecondEncapsulationVlan 45 filterSecondEncapsulationVlan 46 bridgeStormDetect 97 bridgeInsertOption82 98 dhcpRelay 99 bridgeInsertPPPoEVendorTag 100 rateLimitDiscard 103 colorAwareRateLimitDiscard 104 aclAllow 114 bridgeForbidOui 120 aclDeny	.1.3.6.1.4.1.5504.4.7.6.3.1.2
packetRuleValue A variable-length field whose meaning depends on packetRuleType. If bridgeForbidOui, it specifies a bit pattern to be matched in a packet, stored as a string, but specified in the pattern 'nn:nn:nn...n…	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.3
packetRuleRowStatus This object is used to create and remove rows in the table.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.6.3.1.4
packetRuleValue2 A variable-length field whose meaning depends on packetRuleType.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.5
packetRuleValue3 A variable-length field whose meaning depends on packetRuleType.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.6
packetRuleValue4 A variable-length field whose meaning depends on packetRuleType.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.7
packetRuleValue5 A variable-length field whose meaning depends on packetRuleType.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.8
packetRuleGroupIndex A scalar representing the Group Index for a set of Packet Rule Table Entries.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.7.6.3.1.9
packetRuleValue6 A variable-length field whose meaning depends on packetRuleType.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.10
packetRuleValue7 A variable-length field whose meaning depends on packetRuleType.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.5504.4.7.6.3.1.11

For PPPoA-to-PPPoE tables, provide a lookup by ifIndex into the
PPPoE tables. If the session has not been created for this PPPoA
ifIndex, then there will be no table data.

bridgePPPoEEntry row .1.3.6.1.4.1.5504.4.7.7.1

Description.

Indexes

IF-MIBifIndex

Column	Syntax	OID
bridgePPPoEBrasMac Destination mac address.	OctetString Constraints: range: 6-6	.1.3.6.1.4.1.5504.4.7.7.1.1
bridgePPPoELocalHostMac Source mac address.	OctetString Constraints: range: 6-6	.1.3.6.1.4.1.5504.4.7.7.1.2
bridgePPPoEEIfIndex PPPoE port's ifIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.5504.4.7.7.1.3
bridgePPPoESessionID PPPoE session ID.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.5504.4.7.7.1.4
bridgePPPoESlanId SLan ID of BRAS.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.5504.4.7.7.1.5
bridgePPPoEVlanId VLAN ID of BRAS.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.5504.4.7.7.1.6
bridgePPPoEEncapLLC PPPoA encapsulation	Enumeration Enumerated Values: 1 vcmux 2 llc	.1.3.6.1.4.1.5504.4.7.7.1.7

The stpBind table is used to store the entries of stpBind
which hold the relationship between the ifIndex on which 
STP is to run on, and the MSTP instance if any.

stpBindEntry row .1.3.6.1.4.1.5504.4.7.9.1

stpBindEntry is used to specify the type of STP
that is to run on an ifIndex. An InstanceID of 0
specifies RSTP.
An InstanceId > 0 indicates MSTP.

Indexes

IF-MIBifIndex stpBindInstanceID

Column	Syntax	OID
stpBindInstanceID This is a hidden storage of the InstanceId of an entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.9.1.1
stpBindRowStatus Description.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.9.1.2
stpBindPortPriority PortPriority is used to specify the STP priority of this port.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.5504.4.7.9.1.3

Description.

mstpInstanceEntry row .1.3.6.1.4.1.5504.4.7.10.1

Description.

Indexes

stpBindInstanceID bridgeIfVlanId

Column	Syntax	OID
mstpInstanceRowStatus Description.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.10.1.1
mstpInstanceName A name for this mstp instance and vlanId.	Zhone-TCZhoneAdminStringr/w Type Constraints: range: 0..32	.1.3.6.1.4.1.5504.4.7.10.1.2

The bridgeStatsTable is used to access the statistics of the entries in the bridge table.

bridgeStatsEntry row .1.3.6.1.4.1.5504.4.7.11.1

Displays the bridge statistics table entries.

Indexes

IF-MIBifIndex

Column	Syntax	OID
bridgeStatsUcastRcvd Unicast packets received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.1
bridgeStatsMcastRcvd Multicast packets received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.2
bridgeStatsBcastRcvd Broadcast packets received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.3
bridgeStatsUcastSent Unicast packets sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.4
bridgeStatsMcastSent Multicast packets sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.5
bridgeStatsBcastSent Broadcast packets sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.6
bridgeStatsErrorSent Error packets sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.7
bridgeOnDemandStatsRulesSupported Get the number of supported Ingress Stats available for a line card.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.8
bridgeOnDemandStatsRulesRemaining Get the number of remaining Ingress Stats available for a line card	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.9
bridgeStatsBSDUcastBlocked Number of unicast packets dropped due to Bridge Packet Storm Detection threshold exceeded.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.10
bridgeStatsBSDMcastBlocked Number of multicast packets dropped due to Bridge Packet Storm Detection threshold exceeded.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.11
bridgeStatsBSDBcastBlocked Number of broadcast packets dropped due to Bridge Packet Storm Detection threshold exceeded.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.12
bridgeStatsBSDAlarmCount This counter reflects the number of times this interface has transitioned to the alarm state due to the Bridge Packet Storm Detection threshold being exceeded for a pre-defined number of seconds.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.11.1.13
bridgeStatsBytesRcvdCount This is a count of the number of bytes received. On-demand stats must be enabled for byte counters otherwise this counter is zero.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.7.11.1.14
bridgeStatsBytesSentCount This is a count of the number of bytes transmitted. On-demand stats must be enabled for byte counters otherwise this counter is zero.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.7.11.1.15
bridgeStatsTicksLastCleared Linecard tick value when bridge was last cleared.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.7.11.1.16
bridgeStatsTicksNow Linecard current tick value.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.7.11.1.17
bridgeStatsTicksPerSecond Linecard current tick value.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.7.11.1.18

This table contains information required for the management
of EAPS domains.

eapsConfigEntry row .1.3.6.1.4.1.5504.4.7.13.1.1

An entry exists for each EAPS domain in the system.

Indexes

eapsConfigPrimaryPortLineGroup eapsConfigSecondaryPortLineGroup eapsConfigControlVlan

Column	Syntax	OID
eapsConfigPrimaryPortLineGroup This object contains the line group IfIndex of the Primary EAPS Port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.5504.4.7.13.1.1.1
eapsConfigSecondaryPortLineGroup This object contains the line group IfIndex of the Secondary EAPS Port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.5504.4.7.13.1.1.2
eapsConfigControlVlan This object contains the VLAN ID of the control VLAN for this domain record. This is the VLAN ID used in EAPS control messages.	Integer32 Constraints: range: 1-4090	.1.3.6.1.4.1.5504.4.7.13.1.1.3
eapsConfigIsMasterNode If this value is True, then this record describes a Master Node. Otherwise, it describes a Transit Node.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.13.1.1.4
eapsConfigControlVlanPriority This object contains the Priority of the Control Vlan.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.5504.4.7.13.1.1.5
eapsConfigDomainName This object contains the user assigned ASCII representation of the Domain Name for this record. This name must be unique device wide.	Zhone-TCZhoneAdminStringr/w Type Constraints: range: 0..32	.1.3.6.1.4.1.5504.4.7.13.1.1.6
eapsConfigMsgTxInterval This object contains the interval, in seconds, that a node sends Health Messages on the ring.	secondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.13.1.1.7
eapsConfigTimeout On a Master Node, this object contains the timeout, in seconds, which the Master Node will report a Ring Fault if it does not receive a Health Message on the ring. On a Transit Node, this is the pre-forwarding delay tim…	secondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.13.1.1.8
eapsConfigMaxDroppedMessages On a Master Node, this object contains the number of contigious Health messages that may be dropped before the node declared a Ring Fault. This object is not used for a Transit node.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.13.1.1.9
eapsConfigSnmpTrap If this object is set to True, then this node will send SNMP Traps on Ring State transition.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.13.1.1.10
eapsConfigDomainEnable If this value is TRUE, the EAPS state machine will transition through the initialization process to the Health state. It will begin passing Control Messages and allow Protected VLAN data through the EAPS Domain. If…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.13.1.1.11
eapsConfigRowStatus This object is used to create and remove rows in the table. See eapsConfigEntry description for minimum requirements.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.13.1.1.12

This table contains information required for the management
of a list of protected VLAN's in an EAPS domains.

eapsProtectedVlanEntry row .1.3.6.1.4.1.5504.4.7.13.2.1

An entry for each VLAN ranges that is to be protected
in the EAPS domain.

Indexes

eapsConfigPrimaryPortLineGroup eapsConfigSecondaryPortLineGroup eapsConfigControlVlan eapsProtectedVlanEntryIndex

Column	Syntax	OID
eapsProtectedVlanEntryIndex This object is an index which indicates which entry in the Protected Vlan Table is being addressed. For example, a value of 5 would indicate that the 5th entry (row) of this table is being addressed. This entry, along …	Integer32 Constraints: range: 0-9	.1.3.6.1.4.1.5504.4.7.13.2.1.1
eapsProtectedVlanLowerRange The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end of list.…	Integer32r/w Constraints: range: 0-4090	.1.3.6.1.4.1.5504.4.7.13.2.1.2
eapsProtectedVlanUpperRange The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end of list.…	Integer32r/w Constraints: range: 0-4090	.1.3.6.1.4.1.5504.4.7.13.2.1.3
eapsProtectedVlanRowStatus This object is used to create and remove rows in the table. See eapsProtectedVlanEntry description for minimum requirements.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.13.2.1.4
eapsProtectedVlanDomainName The domain name for the EAPS protected vlan entry.	Zhone-TCZhoneAdminString Type Constraints: range: 0..32	.1.3.6.1.4.1.5504.4.7.13.2.1.5

This table contains status of each EAPS domain state machine.

eapsStatusEntry row .1.3.6.1.4.1.5504.4.7.13.3.1

The entry contains status of the domain's state machine.

Indexes

eapsConfigPrimaryPortLineGroup eapsConfigSecondaryPortLineGroup eapsConfigControlVlan

Column	Syntax	OID
eapsPrevState Previous state for the domain.	EapsState Type Values: 0 idle 1 complete 2 failed 3 links-up 4 link-down 5 preForwarding 6 init	.1.3.6.1.4.1.5504.4.7.13.3.1.1
eapsState Current state for the domain.	EapsState Type Values: 0 idle 1 complete 2 failed 3 links-up 4 link-down 5 preForwarding 6 init	.1.3.6.1.4.1.5504.4.7.13.3.1.2

EAPS statistics table.

eapsStatsEntry row .1.3.6.1.4.1.5504.4.7.13.4.1

Displays the EAPS statistic table entries.

Indexes

eapsConfigPrimaryPortLineGroup eapsConfigSecondaryPortLineGroup eapsConfigControlVlan

Column	Syntax	OID
eapsStatsTotCtrlMsgSent Total EAPS control messages sent.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.13.4.1.1
eapsStatsTotCtrlMsgRecvd Total EAPS control messages received.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.13.4.1.2

EAPS topology table.

eapsTopologyEntry row .1.3.6.1.4.1.5504.4.7.13.6.1

Displays the EAPS topology table entries.

Indexes

eapsConfigPrimaryPortLineGroup eapsConfigSecondaryPortLineGroup eapsTopologyRing eapsTopologyRowNumber

Column	Syntax	OID
eapsTopologyRing This represents the link as primary or secondary.	Enumeration Enumerated Values: 0 primary 1 secondary	.1.3.6.1.4.1.5504.4.7.13.6.1.1
eapsTopologyRowNumber This represents the node number in the ring.	Integer32 Constraints: range: 0-47	.1.3.6.1.4.1.5504.4.7.13.6.1.2
eapsTopologyDomainName This represents the domain name for this record.	Zhone-TCZhoneAdminString Type Constraints: range: 0..32	.1.3.6.1.4.1.5504.4.7.13.6.1.3
eapsTopologyMacAddr macAddress of the element in the ring.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.5504.4.7.13.6.1.4
eapsTopologyIpAddr Ip addressed of the element in the ring.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.5504.4.7.13.6.1.5
eapsTopologyType This represents whether the node is master or transit.	Enumeration Enumerated Values: 0 master 1 transit	.1.3.6.1.4.1.5504.4.7.13.6.1.6
eapsTopologyPrimaryLinkName This represents the primary link name.	Zhone-TCZhoneAdminString Type Constraints: range: 0..32	.1.3.6.1.4.1.5504.4.7.13.6.1.7
eapsTopologyPrimaryLinkState This represents the primary link state.	EapsState Type Values: 0 idle 1 complete 2 failed 3 links-up 4 link-down 5 preForwarding 6 init	.1.3.6.1.4.1.5504.4.7.13.6.1.8
eapsTopologySecondaryLinkName This represents the secondary link name.	Zhone-TCZhoneAdminString Type Constraints: range: 0..32	.1.3.6.1.4.1.5504.4.7.13.6.1.9
eapsTopologySecondaryLinkState This represents the secondary link state.	EapsState Type Values: 0 idle 1 complete 2 failed 3 links-up 4 link-down 5 preForwarding 6 init	.1.3.6.1.4.1.5504.4.7.13.6.1.10

The bridgeIgmpStatsTable is used to access the IGMP statistics for bridges.

bridgeIgmpStatsEntry row .1.3.6.1.4.1.5504.4.7.14.1

The bridgeIgmpStatsEntry holds IGMP stats for a bridge interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
genQueryRx general IGMP queries received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.1
genQueryTx general IGMP queries transmitted.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.2
specQueryRx Specific IGMP queries received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.3
specQueryTx Specific IGMP queries transmitted.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.4
v2ReportsRx Version 2 reports received (JOINs).	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.5
v2ReportsTx Version 2 reports sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.6
leavesRx IGMP leaves received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.7
leavesTx IGMP leaves transmitted.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.8
unknownRx Unknown IGMP packets received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.9
errorRx IGMP packet is bad received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.10
actChans Number of active muticast channels.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.11
actHosts Number of active multicast hosts.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.12
v3GenQueryRx Number of IGMP V3 Queries received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.13
v3GenQueryTx Number of IGMP V3 queries sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.14
v3SpecQueryRx Number of IGMP V3 specific queries received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.15
v3SpecQueryTx Number of IGMP V3 specific queries sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.16
v3ReportsRx Number of IGMP V3 reports received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.17
v3ReportsTx Number of IGMP V3 reports sent.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.7.14.1.18

The bridgeIgmpTable is used to access the IGMP data for bridges for when 
IGMP is in proxy mode and the IGMP status must be obtained from the 
linecard.

bridgeIgmpEntry row .1.3.6.1.4.1.5504.4.7.17.1

BridgeIgmpEntry contains the igmp multicast data information for a bridge,
indexed by ifIndex, hostMac, and mcastMac.

Indexes

IF-MIBifIndex hostMac mcastMac

Column	Syntax	OID
slanId IGMP slan identifier. Maximum value 4090 as defined by MAX_VLAN_NUM.	Integer32 Constraints: range: 0-4090	.1.3.6.1.4.1.5504.4.7.17.1.1
vlanId IGMP vlan identifier. Maximum value 4090 as defined my MAX_VLAN_NUM	Integer32 Constraints: range: 0-4090	.1.3.6.1.4.1.5504.4.7.17.1.2
mcastMac IGMP Multicast MAC addressed to bridge port.	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.5504.4.7.17.1.3
mcastIP IGMP Multicast IP addressed to bridge port.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.5504.4.7.17.1.4
hostMac MAC address of end device receiving multicast packets.	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.5504.4.7.17.1.5
lastJoinTimer Count down timer before IGMP entry ages out.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.17.1.6

A collection of staticBridgePathEntries.
          
The StaticBridgePath OID has the following format:
          
      OID psn      MAC entries     IPv4 entries     IPv6 entries
     ----------    -------------   --------------   --------------
     tlist[0]       ifIndex          ifIndex          ifIndex
     tlist[1]       address type     address type     address type
     tlist[2]       vlan             vlan             vlan
     tlist[3]       macAddr[0]       IPv4[0]          IPv6[0]
     tlist[4]       macAddr[1]       IPv4[1]          IPv6[1]
     tlist[5]       macAddr[2]       IPv4[2]          IPv6[2]
     tlist[6]       macAddr[3]       IPv4[3]          IPv6[3]
     tlist[7]       macAddr[4]       zero             IPv6[4]
     tlist[8]       macAddr[5]       zero             IPv6[5]
     tlist[9]       zero             zero             IPv6[6]
     tlist[10]      zero             zero             IPv6[7]
     tlist[11]      zero             zero             IPv6[8]
     tlist[12]      zero             zero             IPv6[9]
     tlist[13]      zero             zero             IPv6[10]
     tlist[14]      zero             zero             IPv6[11]
     tlist[15]      zero             zero             IPv6[12]
     tlist[16]      zero             zero             IPv6[13]
     tlist[17]      zero             zero             IPv6[14]
     tlist[18]      zero             zero             IPv6[15]
     tlist[19]      slan             slan             slan

staticBridgePathEntry row .1.3.6.1.4.1.5504.4.7.18.1

Static Path Bridge entries are created by the user in
order to specify forwarding for a particular
interface, vlanId, mac address or ip address,
slanId (for QinQ).

The INDEX value for staticBridgePathEntr…

Indexes

IF-MIBifIndex staticBridgePathAddressType bridgeIfVlanId staticBridgePathMacOrIpAddress bridgeIfStagId

Column	Syntax	OID
staticBridgePathMacOrIpAddress If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this field represents an IP address. The IP addres…	NetworkAddress	.1.3.6.1.4.1.5504.4.7.18.1.1
staticBridgePathAddressType If staticBridgeIPv6AddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If s…	Enumeration Enumerated Values: 1 macAddr 2 ipAddr 3 vlanIdAddr 4 globalAddr 7 intralinkAddr 8 globalIntralinkAddr 9 dhcpIpAddr 10 dhcpMacAddr 13 mvrAddr 14 vlanParms 15 secMvrAddr 16 ipAddrV6 17 dhcpIpAddrV6 720901 dhcpAllowOui	.1.3.6.1.4.1.5504.4.7.18.1.2
staticBridgePathMulticastAging Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turn…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.7.18.1.3
staticBridgePathRowStatus Used to create, modify or delete an entry in this table.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.7.18.1.4
staticBridgePathFlapControl This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) turn flap control mode on. 'Enable(3)' applies a hold time…	Enumerationr/w Enumerated Values: 1 default 2 disable 3 enable 4 fast	.1.3.6.1.4.1.5504.4.7.18.1.5
staticBridgePathUnicastAging Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turn…	Integer32r/w Constraints: range: 0-0 range: 120-2147483647	.1.3.6.1.4.1.5504.4.7.18.1.6
staticBridgePathIgmpQueryInterval How often (in seconds) we as a bridge inject IGMP query values into the stream.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.7.18.1.7
staticBridgePathFlags none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondToQuery) : igmpRes…	Bitsr/w Enumerated Values: 0 igmpProcessJoinAndLeave 1 igmpRespondToQuery 2 igmpUseBridgeIpAddress	.1.3.6.1.4.1.5504.4.7.18.1.8
staticBridgePathIgmpCustomIpAddress Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.5504.4.7.18.1.9
staticBridgePathLoopPrevention This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a learning bridge if it f…	Enumerationr/w Enumerated Values: 0 none 1 blockAsym 2 blockAll 3 blockAsymAuto 4 blockAllAuto	.1.3.6.1.4.1.5504.4.7.18.1.10
staticBridgePathIgmpDscp This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (001010) …	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.5504.4.7.18.1.11

A collection of bridgePathIfLookupTable entries.
          
The bridgePathIfLookup OID has the following format:
          
      OID psn      MAC entries     IPv4 entries     IPv6 entries
     ----------    -------------   --------------   --------------
     tlist[0]       address type     address type     address type
     tlist[1]       macAddr[0]       IPv4[0]          IPv6[0]
     tlist[2]       macAddr[1]       IPv4[1]          IPv6[1]
     tlist[3]       macAddr[2]       IPv4[2]          IPv6[2]
     tlist[4]       macAddr[3]       IPv4[3]          IPv6[3]
     tlist[5]       macAddr[4]       zero             IPv6[4]
     tlist[6]       macAddr[5]       zero             IPv6[5]
     tlist[7]       zero             zero             IPv6[6]
     tlist[8]       zero             zero             IPv6[7]
     tlist[9]       zero             zero             IPv6[8]
     tlist[10]      zero             zero             IPv6[9]
     tlist[11]      zero             zero             IPv6[10]
     tlist[12]      zero             zero             IPv6[11]
     tlist[13]      zero             zero             IPv6[12]
     tlist[14]      zero             zero             IPv6[13]
     tlist[15]      zero             zero             IPv6[14]
     tlist[16]      zero             zero             IPv6[15]
     tlist[17]      vlan             vlan             vlan
     tlist[18]      ifIndex          ifIndex          ifIndex
     tlist[19]      slan             slan             slan

bridgePathIfLookupEntry row .1.3.6.1.4.1.5504.4.7.19.1

Bridge IfLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.

The INDEX value for bridgeIfLo…

Indexes

bridgePathIfAddressType bridgePathIfMacOrIpAddress bridgeIfVlanId IF-MIBifIndex bridgeIfStagId

Column	Syntax	OID
bridgePathIfAddressType If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddre…	Enumeration Enumerated Values: 1 unicastMac 2 multicastMac 3 ipAddress 4 dhcpMac 5 dhcpIp	.1.3.6.1.4.1.5504.4.7.19.1.1
bridgePathIfMacOrIpAddress If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress represents a MAC Address. If bridgeIfAddressTy…	NetworkAddress	.1.3.6.1.4.1.5504.4.7.19.1.2
bridgePathIfLookupStaticOrDynamic If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.	Enumeration Enumerated Values: 1 staticEntry 2 dynamicEntry	.1.3.6.1.4.1.5504.4.7.19.1.3
bridgePathIfLookupFlush The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of address type, MAC or IP address and vlan ID is used to deter…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.19.1.4

A collection of bridgePathAddressLookupTable entries.
          
The bridgePathAddressLookup OID has the following format:
          
      OID psn      MAC entries     IPv4 entries     IPv6 entries
     ----------    -------------   --------------   --------------
     tlist[0]       ifIndex          ifIndex          ifIndex
     tlist[1]       address type     address type     address type
     tlist[2]       macAddr[0]       IPv4[0]          IPv6[0]
     tlist[3]       macAddr[1]       IPv4[1]          IPv6[1]
     tlist[4]       macAddr[2]       IPv4[2]          IPv6[2]
     tlist[5]       macAddr[3]       IPv4[3]          IPv6[3]
     tlist[6]       macAddr[4]       zero             IPv6[4]
     tlist[7]       macAddr[5]       zero             IPv6[5]
     tlist[8]       zero             zero             IPv6[6]
     tlist[9]       zero             zero             IPv6[7]
     tlist[10]      zero             zero             IPv6[8]
     tlist[11]      zero             zero             IPv6[9]
     tlist[12]      zero             zero             IPv6[10]
     tlist[13]      zero             zero             IPv6[11]
     tlist[14]      zero             zero             IPv6[12]
     tlist[15]      zero             zero             IPv6[13]
     tlist[16]      zero             zero             IPv6[14]
     tlist[17]      zero             zero             IPv6[15]
     tlist[18]      vlan             vlan             vlan
     tlist[19]      slan             slan             slan

bridgePathAddressLookupEntry row .1.3.6.1.4.1.5504.4.7.20.1

BridgePathAddressLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.

The INDEX value for br…

Indexes

IF-MIBifIndex bridgeIfAddressType bridgePathIfLookupStaticOrDynamic bridgeIfVlanId bridgeIfStagId

Column	Syntax	OID
bridgePathAddressLookupStaticOrDynamic If bridgePathAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgePathAddressLookupStaticOrDynamic is set to 2, then this table entry is learned and is not pe…	Enumeration Enumerated Values: 1 staticEntry 2 dynamicEntry	.1.3.6.1.4.1.5504.4.7.20.1.1
bridgePathAddressLookupFlush The object 'bridgePathAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used to determine which interface is to be removed. Setting t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.7.20.1.2

This table contains runtime status for each bridge interface.

bridgeStatusEntry row .1.3.6.1.4.1.5504.4.7.21.1

Runtime status data for a single bridge.

Indexes

IF-MIBifIndex

Column	Syntax	OID
bridgeStatusState Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N…	BridgeState Type Values: 1 up 2 down 3 trouble 4 notAvailable 5 initializing 6 adminDown 7 adminStateTest 8 adminStateNone 9 ready 10 discovering 11 unknown 12 blocked 13 pending 14 disabled 15 learning 16 forwarding 17 blockedFlapping 18 blockedPersistent 19 blockedFlappingPersistent	.1.3.6.1.4.1.5504.4.7.21.1.1