ZHONE-COM-ATM-MIB Table View

Zhone extension table for the atmVclTable defined in
rfc2515.

zhoneAtmVclExtEntry row .1.3.6.1.4.1.5504.4.2.2.1.1

An entry in the atmVclExtTable.

atmVclExtEntry is an augmentation to the atmVclEntry
defined in rfc2515.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneAtmVclExtFaultDetectionType This is used to configure VCL fault detection. The valid values are: * disabled - Fault detection is disabled. This is the default. * oamF5Loopback - This option uses standard OAM fault management cells…	Enumerationr/w Enumerated Values: 1 disabled 2 oamF5Loopback	.1.3.6.1.4.1.5504.4.2.2.1.1.1
zhoneAtmVclExtOamF5Ping This is used to send a OAM F5 loopback cell for fault detection. The value will automatically revert to disabled after the set is complete. The valid values are: * disabled - OAM F5 loopback cell is not b…	Enumerationr/w Enumerated Values: 1 disabled 2 endToEnd 3 segment	.1.3.6.1.4.1.5504.4.2.2.1.1.2
zhoneAtmVclExtOamF5PingStatus TRUE if ping was successfull and FALSE if failed	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.2.2.1.1.3
zhoneAtmVclExtTrafficContainerIndex Index number of a PON traffic container associated with a VCL definition.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.2.2.1.1.4
zhoneAtmVclExtOamF4Ping This is used to send a OAM F4 loopback cell for fault detection. The value will automatically revert to disabled after the set is complete. The valid values are: * disabled - OAM F4 loopback cell is not b…	Enumerationr/w Enumerated Values: 1 disabled 2 endToEnd 3 segment	.1.3.6.1.4.1.5504.4.2.2.1.1.5
zhoneAtmVclExtOamF4PingStatus TRUE if ping was successfull and FALSE if failed.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.2.2.1.1.6

Zhone extension table for the  atmTrafficDescrParamTable 
defined in rfc2515.

zhoneAtmTrafficDescrParamExtEntry row .1.3.6.1.4.1.5504.4.2.2.4.1

This is extension of AtmTrafficDescrParamEntry defined
in rfc2515.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneAtmTrafficDescrParamExtTrnkVclRate This field is used to describe the minimum guaranteed rate for a VCL which is bound to this traffic descriptor for BAN ATM Trunk Cards. It is applicable only for RTVBR service category. Unlike switched voice calls in…	Enumerationr/w Enumerated Values: 1 unused 2 rate16K 3 rate32K 4 rate64K 5 rate80K 6 rate128K 7 rate160K 8 rate256K 9 rate320K 10 rate512K 11 rate640K 12 rate1552K 13 rate2050K 14 rate12M 15 rate16M 16 rate45M 17 rate155M 18 rate960K 19 rate1280K 20 rate1760K 21 rate3M 22 rate4M 23 rate5M 24 rate6M 25 rate7M 26 rate8M 27 rate10M 28 rate14M 29 rate24M 30 rate32M 31 rate64M 32 rate96M 33 rate128M	.1.3.6.1.4.1.5504.4.2.2.4.1.1
zhoneAtmTrafficDescrParamExtCacDivider This object allows users to oversubsribe. The rate subtracted from CAC is PCR or SCR divided by this object.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.2.2.4.1.2
zhoneAtmTrafficDescrParamExtUsageParameterControl If set to 'false', this object disables polcing.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.2.2.4.1.3

These statistics values are coming from fabric interface.

zhoneAtmStatsExtEntry row .1.3.6.1.4.1.5504.4.2.2.5.1

Definitions of Forward and Backward:

Internal to ATM Switch Fabric
=============================================================
|Ext|==>IngressFwd==>| |==>EgressFwd====>|Int|
PortPhy<->|VC …

Indexes

No indexes recorded

Column	Syntax	OID
zhoneAtmStatsTotalInitialCellsRx Total Initial Cells Received. Total cells received across the ingress interface for a given VC, and not discarded by policing prior to thresholding (includes CPU insertions but excludes Atm switch fabric generated ing…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.1
zhoneAtmStatsTotalFabricCellsRx Total Cells Recevied at Fabric.Total cells received across the fabric interface for a given VC, including cells discarded due to parity errors.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.2
zhoneAtmStatsTotalFinalCLP0CellsRx Total CLP0 Cells received by fabric. This field is setup to monitor egress total cells transmitted CLP0.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.3
zhoneAtmStatsTotalFinalCLP1CellsRx Total CLP1 Cells received by fabric. This field is setup to monitor egress total cells transmitted CLP1.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.4
zhoneAtmStatsTotalInitialCellsTx Initial Total Cells Transmitted. Total cells transmitted. across the ingress interface for a given VC, and not discarded by policing prior to thresholding (includes CPU insertions but excludes Atm switch fabric gener…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.5
zhoneAtmStatsTotalFabricCellsTx Total cells transmitted at fabric interace.Total cells transmitted across the fabric interface for a given VC, including cells discarded due to parity errors.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.6
zhoneAtmStatsTotalFinalCLP0CellsTx Total CLP0 Cells Transmitted. This field is setup to monitor egress total cells transmitted CLP0.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.7
zhoneAtmStatsTotalFinalCLP1CellsTx Total CLP1 Cells Transmitted. This field is setup to monitor egress total cells transmitted CLP1.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.5504.4.2.2.5.1.8

Zhone extension table for the atmVplTable defined in
rfc2515.

zhoneAtmVplExtEntry row .1.3.6.1.4.1.5504.4.2.2.7.1

NOT CURRENTLY IMPLEMENTED.

An entry in the atmVplExtTable.

atmVplExtEntry is an augmentation to the atmVplEntry
defined in rfc2515.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneAtmVplExtFaultDetectionType NOT CURRENTLY IMPLEMENTED. This is used to configure VPL fault detection. The valid values are: * disabled - Fault detection is disabled. This is the default. * oamF4Loopba…	Enumerationr/w Enumerated Values: 1 disabled 2 oamF4Loopback	.1.3.6.1.4.1.5504.4.2.2.7.1.1
zhoneAtmVplExtTrafficContainerIndex Index number of a PON traffic container associated with a VPL definition. NOTE: MULTIPLE VARBINDS ACROSS THE VPL TABLE AND THE VPL EXTENSI0N TABLE ARE NOT ALLOWED! It turns out that anyone trying to set …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.5504.4.2.2.7.1.2

Table which describes the allocated and available ATM
connections on a Zhone device.

zhoneAtmConnectionStatsEntry row .1.3.6.1.4.1.5504.4.2.2.8.1

An entry based on shelf/slot which describes the
total allocated and available ATM connections for
that shelf/slot.

Indexes

ZhonezhoneShelfIndex ZhonezhoneSlotIndex

Column	Syntax	OID
zhoneAtmConnectionsAvailable The total available ATM connections for a particular shelf/slot. This number is hardware dependent. Whenever a VPI is allocated for a particular shelf/slot, the number of connections alloca…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.2.2.8.1.1
zhoneAtmConnectionsAllocated The total allocated ATM connections for a particular shelf/slot. For a particular VPI, we calculate the number of connections allocated by the following rule: A VP Switched VPI has a Max VC…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.2.2.8.1.2

Table which describes attributes associated to a
particular VPI.
          
Anytime you add to, delete from or modify any entry
in this table, you must reboot the card in order for
these changes to take effect.  The reason for this is
that the APC must be re-programmed and the only way
to do this is by doing a reboot.
          
In addition, you will not be allowed to modify, create
or delete any atm-vcl entry which is on the same card
as the VPI until after the card has been rebooted.

zhoneAtmVpiEntry row .1.3.6.1.4.1.5504.4.2.2.9.1

An entry based on ifIndex/vpi (which resolves to a
particular shelf/slot/port/subport/type/vpi) which
contains the maximum VCI value and the switch mode
(either vp or vc switched) for a particular VPI.

Indexes

IF-MIBifIndex ATM-MIBatmVplVpi

Column	Syntax	OID
zhoneAtmVpiMaxVci For the selected VPI, this value contains the maximum VCI. For vp switched VPIs, this value must be zero. For vc switched VPIs, this value must be a power of 2 with its maximum value being …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.2.2.9.1.1
zhoneAtmVpiSwitched For the selected VPI, this value can be set to either vp switched or vc switched. If it is vp switched, then the max vci must be zero. If it is vc switched, the max vci value must be a powe…	Enumerationr/w Enumerated Values: 1 vp 2 vc	.1.3.6.1.4.1.5504.4.2.2.9.1.2
zhoneAtmVpiRowStatus Row Status only supports create-and-go and destroy actions. Returns active if row is in service.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.2.2.9.1.3
zhoneAtmVpiOamF4Ping This is used to send a OAM F4 loopback cell for fault detection. The value will automatically revert to disabled after the set is complete. The valid values are: * disabled - OAM F4 loopback cell is not b…	Enumerationr/w Enumerated Values: 1 disabled 2 endToEnd 3 segment	.1.3.6.1.4.1.5504.4.2.2.9.1.4
zhoneAtmVpiOamF4PingStatus TRUE if ping was successfull and FALSE if failed.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.4.2.2.9.1.5
zhoneAtmVpiMaxVciPerVp If vp-switched, but VG connection is vc-switched, this specifies max number of vci on gateway.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5504.4.2.2.9.1.6

The Multicast Address to Vcl Mapping table.  Each 
entry in this table associates a multicast address 
representing a video stream with a Vcl.  All of the
entries in this table are assumed to be unique, not
only in terms of index, but in terms of (index,
multicast address) <-> (ifIndex, vpi, vci).
          
Note that the Vcl type for this table should always
be 'other', denoting cell relay pass-through.  We
are not terminating the IP stream on the MALC.
          
Also note that the Vcls that this table refer to
are the ones originating at the Video Head-End,
coming into the MALC Uplink card.

atmVclToMulticastMapEntry row .1.3.6.1.4.1.5504.4.2.2.16.2.1

An entry in the Multicast Address to Vcl Mapping table.
This entry is used to associate a multicast address with
a Vcl.

Step-wise Procedures to set up a Multicast Vcl Mapping profile

Once the …

Indexes

atmVclToMulticastMapIndex

Column	Syntax	OID
atmVclToMulticastMapIndex A unique value to identify this Multicast Address to Vcl mapping.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.5504.4.2.2.16.2.1.1
atmVclToMulticastMapRoutingDomain Routing domain of the Head-End video server.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.5504.4.2.2.16.2.1.2
atmVclToMulticastMapMulticastAddress Multicast IP address contained in the MPEG2 video stream.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.5504.4.2.2.16.2.1.3
atmVclToMulticastMapIfIndex The ifIndex value of the ATM interface for the Vcl carrying a video stream.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.5504.4.2.2.16.2.1.4
atmVclToMulticastMapVpi The VPI value of the ATM interface for the Vcl carrying a video stream.	ATM-TC-MIBAtmVpIdentifierr/w Type Constraints: range: 0..4095	.1.3.6.1.4.1.5504.4.2.2.16.2.1.5
atmVclToMulticastMapVci The VCI value of the ATM interface for the Vcl carrying a video stream.	ATM-TC-MIBAtmVcIdentifierr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.5504.4.2.2.16.2.1.6
atmVclToMulticastMapRowStatus Row status of the multicast address to Vcl table entry. This object must be initially set to 'createAndGo'.	Zhone-TCZhoneRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.5504.4.2.2.16.2.1.7

This table contains ATM interface TC
Sublayer parameters and state variables,
one entry per ATM interface port.

zhoneAtmInterfaceTcExtEntry row .1.3.6.1.4.1.5504.4.2.2.19.1

This list contains TC Sublayer parameters
and state variables at the ATM interface and is
indexed by the ifIndex value of the ATM interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneAtmInterfaceNCDEvents The number of times the Near-end No Cell Delineation (NCD) events occur.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.2.2.19.1.1
zhoneAtmInterfaceHECEvents The number of times Near-end Header Error Control (HEC) violations occur.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.2.2.19.1.2
zhoneAtmInterfaceFeOCDEvents The number of times Far-end Out of Cell Delineation (OCD) events occur.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.2.2.19.1.3
zhoneAtmInterfaceFeNCDEvents The number of times Far-end No Cell Delineation (NCD) events occur.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.2.2.19.1.4
zhoneAtmInterfaceFeHECEvents The number of times Far-end Header Error Control (HEC) violations occur.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.4.2.2.19.1.5

This Table contains Atm Vc Cross Connect Extensions 
to the atmVcCrossConnectEntry.

zhoneAtmVcCrossConnectExtEntry row .1.3.6.1.4.1.5504.4.2.2.20.1

This list contains Atm Vc Cross Connect Extensions
to the atmVcCrossConnectEntry.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneAtmVcCrossConnectExtHandleId An administratively-assigned name for the Atm Vc Cross Connect indicated by the INDEX value.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.5504.4.2.2.20.1.1