WESTERMO-WEOS-MIB Table View

Table containing Westermo Link Fail Forward (LFF) settings and status
applicable ports.
Westermo LFF is used to indicate the state (up/down) of a remote link.
The currently supported use case is when extending an Ethernet over an SHDSL link.
LFF is used to inform the local end that the Ethernet link at the remote site is
up or down.

lffEntry row .1.3.6.1.4.1.16177.2.1.2.1.1

For each local (SHDSL) port, there is a row in the lffTable containing
LFF status and settings.

Indexes

lffPortIfIndex

Column	Syntax	OID
lffPortIfIndex This index should map to the local (SHDSL) port's ifIndex in the ifTable.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.2.1.1.1
lffPortIfName This name should map to the local (SHDSL) port's ifName in the ifXTable.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.2.1.1.2
lffStatus The lffStatus shows the status of a (Ethernet) link at the remote end of a SHDSL link: - 1 (disabled): LFF is configured 'disabled' on local (SHDSL) port. - 2 (unknown): LFF enabled, but the state of remote (Ether…	Enumeration Enumerated Values: 1 disabled 2 unknown 3 remoteDown 4 remoteUp	.1.3.6.1.4.1.16177.2.1.2.1.1.3

Table containing DDM diagnostics per DDM capable SFP.

sfpDdmPortEntry row .1.3.6.1.4.1.16177.2.1.2.2.1.1

This row in the sfpDdmPortTable containing per port
SFP DDM diagnostics.

Indexes

sfpDdmPortIfIndex

Column	Syntax	OID
sfpDdmPortIfIndex This index maps to the port's ifIndex in the ifTable.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.2.2.1.1.1
sfpDdmPortIfName The system name of the port.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.2.2.1.1.2
sfpDdmPortVoltage The supply voltage of the SFP. The accuracy is better than +/-3 % and the total range of 0 - 6550 mV. The voltage is represented in mV.	Integer32 Constraints: range: 0-6550	.1.3.6.1.4.1.16177.2.1.2.2.1.1.3
sfpDdmPortTemperature Temperature of the SFP. The temperature accuracy is better than 3 degrees Celsius and the total range of -128 degrees C to +128 degrees C.	Integer32 Constraints: range: -128-128	.1.3.6.1.4.1.16177.2.1.2.2.1.1.4
sfpDdmPortBiasCurrent The transmitt bias current. The accuracy is better than +/- 10 % and the total range of 0 - 131 mA. The current is represented in uA.	Integer32 Constraints: range: 0-131	.1.3.6.1.4.1.16177.2.1.2.2.1.1.5
sfpDdmPortTxPower Transmitt power of the laser. The accuracy is better than +/-3dB and the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented in steps of 0.01 dBm	Integer32 Constraints: range: -4000-820	.1.3.6.1.4.1.16177.2.1.2.2.1.1.6
sfpDdmPortRxPower Receiving power of the laser. The accuracy is better than +/-3dB and the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented in steps of 0.01 dBm	Integer32 Constraints: range: -4000-820	.1.3.6.1.4.1.16177.2.1.2.2.1.1.7

Table containing port bandwidth rates.

bwStatsEntry row .1.3.6.1.4.1.16177.2.1.2.3.2.1

For each local port, there is a row in the bwStatsTable containing
port bandwidth rates.

Indexes

bwStatsIndex

Column	Syntax	OID
bwStatsIndex The value of this object uniquely identifies this bwStats entry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.2.3.2.1.1
bwStatsEnabled Bandwidth statistics enabled or disabled for this port.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.2.3.2.1.2
bwStatsBitrateIn10s The current average input traffic for the last 10 seconds. This value is calculated via periodic sampling of the port counters And will be updated at least every 10 seconds. The unit is bits per second and this includes…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.3
bwStatsBitrateOut10s The current average output traffic for the last 10 seconds. This value is calculated via periodic sampling of the port counters And will be updated at least every 10 seconds. The unit is bits per second and this include…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.4
bwStatsBitrateIn1m The current moving average input traffic for the last minute. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not inc…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.5
bwStatsBitrateOut1m The current moving average output traffic for the last minute. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not in…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.6
bwStatsBitrateIn10m The current moving average input traffic for the last 10 minutes. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.7
bwStatsBitrateOut10m The current moving average output traffic for the last 10 minutes. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble no…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.8
bwStatsBitrateIn1h The current moving average input traffic for the last hour. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not inclu…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.9
bwStatsBitrateOut1h The current moving average output traffic for the last hour. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not incl…	Bits per secondSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.16177.2.1.2.3.2.1.10

Table containing VLAN priority settings for
existing VLANs.

l2QosVlanEntry row .1.3.6.1.4.1.16177.2.1.3.2.1.1

The row in the l2QosVlanTable containing per VLAN
priority settings.

Indexes

l2QosVlanId

Column	Syntax	OID
l2QosVlanId This index should be mapped to the VLAN ID of Q-bridge MIB.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.16177.2.1.3.2.1.1.1
vlanPriorityEnabled Enable (true) or disable (false) VLAN priority for this VLAN.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.2.1.1.2
vlanPriorityLevel The VLAN priority level for this VLAN. 0 is lowest and 7 is highest priority.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.16177.2.1.3.2.1.1.3

Table containing per port piority settings for LAN ports

l2QosPortEntry row .1.3.6.1.4.1.16177.2.1.3.2.2.1

The row in the l2QosPortTable containing per port
priority settings.

Indexes

l2QosPortIfIndex

Column	Syntax	OID
l2QosPortIfIndex This index should map to the port's ifIndex in the ifTable.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.3.2.2.1.1
l2QosPortIfName This name should map to the port's ifName in the ifXTable.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.3.2.2.1.2
l2QosPortPriorityMode The priority mode (tag, ip or port) to be used on this specific port. 1. (tag): Use the incoming packet's VLAN tag priority value to determine its priority. (Untagged packets will have their priority based on the config…	Enumerationr/w Enumerated Values: 1 tag 2 ip 3 port	.1.3.6.1.4.1.16177.2.1.3.2.2.1.3
l2QosPortPriorityLevel The port priority level for this port. 0 is lowest and 7 is highest priority.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.16177.2.1.3.2.2.1.4

Table containing a list of FRNTv0 instances/rings.

frntv0Entry row .1.3.6.1.4.1.16177.2.1.3.3.1.1.1

The row in the frntv0Table containing settings and status information
for a specific FRNTv0 instance/ring.

Indexes

frntv0InstanceId

Column	Syntax	OID
frntv0InstanceId The instance id of this FRNTv0 Ring (only of local significance to this unit).	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.1
frntv0FocalPointEnabled True(1) if this unit is configured as focal point for this FRNTv0 instance. False(2) if this unit is configured as member switch for this FRNTv0 instance.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.2
frntv0Port1 Name of FRNT port M in the FRNT port pair. In case the unit is configured as focal point and the ring is fully connected, it is port M that is put in BLOCKING.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.3
frntv0Port2 Name of FRNT port N in the FRNT port pair. In case of an edge in a FRNT bus rather than a node in a FRNT ring then port N shall be set to 'None' and it will be read as 'None'. In case the unit is configured as focal poi…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.4
frntv0Port1State Provides information about the status of FRNT port M. See frntv0RingStatus for more details.	Enumeration Enumerated Values: 1 disabled 2 blocking 4 learning 5 forwarding	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.5
frntv0Port2State Provides information about the status of FRNT port N. See frntv0RingStatus for more details.	Enumeration Enumerated Values: 1 disabled 2 blocking 4 learning 5 forwarding	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.6
frntv0RingStatus Read ring status information. The answer is to be interpreted differently when asking a focal point or a member switch. Focal point (status of the whole FRNT topology): 1. ring mode: A focal point reports…	Enumeration Enumerated Values: 1 ring 2 bus	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.7
frntv0RowStatus This object indicates the status of this table entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.8
frntv0TopologyChangeCount This object indicates the number of transitions between bus/ring mode since FRNT was enabled.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.9
frntv0TopologyTimeSinceLastChange This object indicates the time that have passed since the last change of ring status.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.10
frntv0PortsSwapped FRNT can detect if the FRNT ports have been swapped. For example if port1 is connected to port1 on another FRNT unit. True(1) if the ports are swapped. False(2) if the ports are not swapped.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.3.1.1.1.11

A list of configuration entries for VLAN specific IGMP Snooping objects.

igmpSnoopingVlanEntry row .1.3.6.1.4.1.16177.2.1.3.4.5.1

An IGMP Snooping VLAN entry contains IGMP Snooping objects relevant for
IGMP Snooping management per VLAN.

Indexes

igmpSnoopingVlanId

Column	Syntax	OID
igmpSnoopingVlanId This index should match corresponding VLAN ID of Q-bridge MIB.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.16177.2.1.3.4.5.1.1
igmpSnoopingEnabled IGMP Snooping enabled or disabled on this particular VLAN.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.4.5.1.2

Table containing status for a list of RiCo and/or Dual Homing
instances present on this unit.

riCoStatusEntry row .1.3.6.1.4.1.16177.2.1.3.5.1.1

Row in the riCoStatusTable that is containing settings and
status information for a specific RiCo/Dual-Homing instance.

Indexes

riCoStatusRingIdx riCoStatusCouplingIdx riCoStatusNodeId

Column	Syntax	OID
riCoStatusRingIdx The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is…	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.3.5.1.1.1
riCoStatusCouplingIdx The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoStatusRingIdx).	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.16177.2.1.3.5.1.1.2
riCoStatusNodeId The unique ID of this RiCo node. A MAC address (typically the base MAC address) of this unit.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.16177.2.1.3.5.1.1.3
riCoStatusHelloInterval Configured RiCo Ring Hello interval in milliseconds. Not applicable for Dual Homing instances (value '0')	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.1.1.4
riCoStatusHelloEffective Effective RiCo Ring Hello interval in milliseconds. Shows negotiated Hello interval. Not applicable for Dual Homing instances (value '0').	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.1.1.5

Table containing status of RiCo and Dual-Homing uplinks per link

riCoStatusUplinkEntry row .1.3.6.1.4.1.16177.2.1.3.5.2.1

The row in the riCoStatusUplinkTable containing status information
for a specific RiCo or Dual-Homing uplink. For RiCo, status
for all local uplinks, and for the best uplink of each RiCo
peer is listed. For dual-homing,…

Indexes

riCoStatusUplinkRingIdx riCoStatusUplinkCouplingIdx riCoStatusUplinkNodeId riCoStatusUplinkIfIndex

Column	Syntax	OID
riCoStatusUplinkRingIdx The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring I…	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.3.5.2.1.1
riCoStatusUplinkCouplingIdx The instance id of this riCo Uplink	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.16177.2.1.3.5.2.1.2
riCoStatusUplinkNodeId The unique ID of the node, i.e., the MAC address of the node. For RiCo, this can be the (base) MAC of the local unit, or the MAC identifying a peer RiCo node. For Dual-Homing, this is the (base) MAC of the local unit.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.16177.2.1.3.5.2.1.3
riCoStatusUplinkIfIndex The interface index of the uplink port. - For local uplinks, this index corresponds to the port's index in the ifTable (IF-MIB). - For non-local uplinks, the value is not valid (value '0').	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.3.5.2.1.4
riCoStatusUplinkStatus Uplink active (1), backup (2) or down (3).	Enumeration Enumerated Values: 1 active 2 backup 3 down	.1.3.6.1.4.1.16177.2.1.3.5.2.1.5
riCoStatusUplinkIfName The name of the interface used for this uplink.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.3.5.2.1.6
riCoStatusUplinkPrio Effective priority of this uplink. Based on configured priority and 'adjust' value (sticky uplink).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.2.1.7
riCoStatusUplinkPathCost Current path cost for this uplink.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.2.1.8
riCoStatusUplinkHelloInterval Configured Ring Hello Interval for the RiCo node of this uplink. Not valid for Dual-Homing, value '0')	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.2.1.9
riCoStatusUplinkHelloIntervalEffective Effective Ring Hello Interval for the RiCo node of this uplink. Not valid for Dual-Homing, value '0')	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.2.1.10
riCoStatusUplinkChangedCounter Number of times this uplink changed its state	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.2.1.11
riCoStatusUplinkSynchronized Synchronization status for this uplink: - synchronized(1): Synchronize enabled and ok - notSynchronized(2): Synchronize enabled and fails - notApplicable(3): Non-local RiCo uplink, or Dual-Homing uplink where Synchr…	Enumeration Enumerated Values: 1 synchronized 2 notSynchronized 3 notApplicable	.1.3.6.1.4.1.16177.2.1.3.5.2.1.12
riCoStatusUplinkPreferred Preferred uplink status. Only valid for Dual-Homing uplinks whit synchronization enabled. - preferred(1): Dual-Homing uplink has status 'Preferred' - notPreferred(2): Dual-Homing uplink has status 'Not Preferred' - notA…	Enumeration Enumerated Values: 1 preferred 2 notPreferred 3 notApplicable	.1.3.6.1.4.1.16177.2.1.3.5.2.1.13
riCoStatusUplinkLocal Local(true) or global(false) instance	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.5.2.1.14

Table containing a list of RiCo couplings.

riCoCfgEntry row .1.3.6.1.4.1.16177.2.1.3.5.3.1

The row in the riCoTable containing settings for a specific
RiCo or Dual-Homing instance.

Indexes

riCoCfgRingIdx riCoCfgCouplingIdx

Column	Syntax	OID
riCoCfgRingIdx The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring I…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.3.5.3.1.1
riCoCfgCouplingIdx The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoCfgRingIdx).	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.16177.2.1.3.5.3.1.2
riCoCfgEnabled Enable or disable the RiCo instance True (1) or False (2)	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.5.3.1.3
riCoCfgHelloInterval Configured RiCo Ring Hello interval in milliseconds. - Default: 100 milliseconds - Configurable in range: 50-1000 milliseconds - Not applicable for Dual Homing instances (value '0')	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.3.1.4
riCoCfgSynchronize Enable/disable Uplink synchronization. 'True' to enable, and 'False' to disable synchronization. Note: Only configurable for Dual-Homing Uplinks. For RiCo Uplinks, synchronization is always enabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.3.5.3.1.5
riCoCfgRowStatus This object indicates the status of this table entry. This object can also be used to create or delete instances. At most 1 RiCo instance and at most 8 Dual-Homing instances can be created.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.16177.2.1.3.5.3.1.6

Table containing RiCo and Dual-Homing uplinks and
corresponding settings per link.

riCoCfgUplinkEntry row .1.3.6.1.4.1.16177.2.1.3.5.4.1

The row in the riCoLinkTable containing settings and status information
for a specific RiCo or Dual-Homing Uplink.

Indexes

riCoCfgRingIdx riCoCfgCouplingIdx riCoCfgUplinkIfIndex

Column	Syntax	OID
riCoCfgUplinkRingIdx The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.3.5.4.1.1
riCoCfgUplinkCouplingIdx The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoStatusRingIdx).	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.16177.2.1.3.5.4.1.2
riCoCfgUplinkIfIndex The interface index of the uplink port. For local uplinks, this index corresponds to the port's index in the ifTable (IF-MIB).	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.3.5.4.1.3
riCoCfgUplinkPrio Configure priority for this uplink (128 as default). A lower value increases the chance to be elected as active uplink.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.4.1.4
riCoCfgUplinkAdjust Configure adjust value for this uplink (sticky uplink). The effictive priority is reduced by the adjust value if the link becomes elected as active uplink. Default '0'.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.4.1.5
riCoCfgUplinkEchoTime Uplink echo interval to be set for this uplink in milliseconds. Default: 200 ms Range: 20-1000 ms	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.4.1.6
riCoCfgUplinkPathCost Path-cost to be set for this uplink. '0' means 'Auto', which lets path cost depend on speed and duplex of the uplink.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.5.4.1.7
riCoCfgUplinkRowStatus This object indicates the status of this table entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.16177.2.1.3.5.4.1.8

The LLDP custom TLV (Type 127) configuration table

lldpCtlvEntry row .1.3.6.1.4.1.16177.2.1.3.6.1.1

A custom TLV entry.

Indexes

lldpCtlvIdx

Column	Syntax	OID
lldpCtlvIdx Index of this custom TLV. Only of local significance.	Integer32 Constraints: range: 1-60	.1.3.6.1.4.1.16177.2.1.3.6.1.1.1
lldpCtlvOui Organizationally unique identifier (OUI), 3 hex-encoded bytes. Required.	OctetStringr/w	.1.3.6.1.4.1.16177.2.1.3.6.1.1.2
lldpCtlvSubType Organizationally defined subtype, one byte. Default: 0	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.3.6.1.1.3
lldpCtlvInfo Information/value part of custom TLV. 0-507 octets encoded as hex. Default: Empty	OctetStringr/w	.1.3.6.1.4.1.16177.2.1.3.6.1.1.4
lldpCtlvRowStatus This object indicates the status of this table entry. Used to create or delete a custom TLV entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.16177.2.1.3.6.1.1.5

Table specifying which custom TLV(s) to transmit per
port. Each row in the table maps a custom TLV to a port. Each
custom TLV in the lldpCtlvTable can be mapped to one or more
ports.

lldpCtlvPortEntry row .1.3.6.1.4.1.16177.2.1.3.6.2.1

Each entry maps a custom TLV to a port.

Indexes

lldpCtlvPortIdx lldpCtlvIdx

Column	Syntax	OID
lldpCtlvPortIdx The logical number of the port. This is the same number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for this port.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.16177.2.1.3.6.2.1.1
lldpCtlvPortCtlvIdx Custom TLV index (lldpCtlvTable)	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.2.1.3.6.2.1.2
lldpCtlvPortRowStatus This object indicates the status of this table entry. Used to create or delete a 'custom TLV to port' mapping.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.16177.2.1.3.6.2.1.3

Table listing all custom TLV(s) received. Each entry
represents a custom TLV received on a specific port from
individual neighbours. Entries are
removed when the TTL of the LLDP message expires, and will be
removed/replaced when a new LLDP message from the same neighbour
is received.

lldpRemCtlvEntry row .1.3.6.1.4.1.16177.2.1.3.6.3.1

Custom TLV received on a port.

Indexes

lldpRemCtlvLocalPort lldpRemCtlvMacAddress lldpRemCtlvOui lldpRemCtlvSubType

Column	Syntax	OID
lldpRemCtlvLocalPort The logical number of the local port receiving this custom TLV. This is the same number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for this port.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.16177.2.1.3.6.3.1.1
lldpRemCtlvMacAddress The MAC address of the neighbour node sending this custom TLV.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.16177.2.1.3.6.3.1.2
lldpRemCtlvOui Organizationally unique identifier (OUI), 3 hex-encoded bytes.	OctetString Constraints: range: 3-3	.1.3.6.1.4.1.16177.2.1.3.6.3.1.3
lldpRemCtlvSubType Organizationally defined subtype, one byte.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.3.6.3.1.4
lldpRemCtlvInfo Information/value part of custom TLV. 0-507 octets encoded as hex.	OctetString	.1.3.6.1.4.1.16177.2.1.3.6.3.1.5

Table containing base IPv4 settings per interface

inet4BaseIfaceEntry row .1.3.6.1.4.1.16177.2.1.4.1.2.2.1

Entry in ipv4Interface table. Each row holds IPv4 settings
specific to this interface.

Indexes

inet4BaseIfIndex

Column	Syntax	OID
inet4BaseIfIndex Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.4.1.2.2.1.1
inet4BaseIfName The name matches the corresponding ifName in the ifXTable.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.4.1.2.2.1.2
inet4BaseAddressMode The IPv4 address assignment mode.	Enumerationr/w Enumerated Values: 1 static 2 dhcp	.1.3.6.1.4.1.16177.2.1.4.1.2.2.1.3

Table containing settings for static IPv4 interfaces

inet4StaticEntry row .1.3.6.1.4.1.16177.2.1.4.1.2.3.1

Entry in ipv4Interface table. Each row holds IPv4 settings specific
to this interface.

Indexes

inet4StatIfIndex

Column	Syntax	OID
inet4StatIfIndex Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.4.1.2.3.1.1
inet4StatIfName The name matches the corresponding ifName in the ifXTable.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.4.1.2.3.1.2
inet4StatAddress Statically configured IPv4 address for this interface. Address 0.0.0.0 means that the interface is disabled.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.2.1.4.1.2.3.1.3
inet4StatNetmask Netmask of statically assigned IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.2.1.4.1.2.3.1.4

Table containing settings for IPv4 interfaces using DHCP for
address assignment

inet4DhcpEntry row .1.3.6.1.4.1.16177.2.1.4.1.2.4.1

Entry in inet4Dhcp table. Each row holds DHCP settings specific
to this interface.

Indexes

inet4DhcpIfIndex

Column	Syntax	OID
inet4DhcpIfIndex Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.4.1.2.4.1.1
inet4DhcpIfName The name matches the corresponding ifName in the ifXTable.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.4.1.2.4.1.2
inet4DhcpClientId Client ID passed by DHCP client to DHCP server.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.4.1.2.4.1.3

A list containing all IP and MAC address conflicts currently
on the this device

addressConflictEntry row .1.3.6.1.4.1.16177.2.1.4.1.4.2.1

An entry containing details for the conflict

Indexes

addressConflictIndex

Column	Syntax	OID
addressConflictIndex A unique value for each conflict.	Integer32 Constraints: range: 0-256	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.1
addressConflictIfIndex Index of the interface on this device.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.2
addressConflictIfName Name of the interface on this device.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.3
addressConflictType Type of conflict: 1 : IP, 2 : MAC, 3 : IP & MAC	Enumeration Enumerated Values: 1 ip 2 mac 3 ipAndMac	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.4
addressConflictMacAddress The MAC address of the conflicting peer.	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.5
addressConflictIPv4Address The IPv4 address of the conflicting peer.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.6
addressConflictTime Time (in seconds) elapsed since conflict was last detected.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.16177.2.1.4.1.4.2.1.7

A list of SNMP trap host.

trapHostEntry row .1.3.6.1.4.1.16177.2.1.5.1.1.2.1

An entry containing information about a specific SNMP trap host.

Indexes

trapHostId

Column	Syntax	OID
trapHostId The id of this SNMP Trap Host (only of local significance to this unit).	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.16177.2.1.5.1.1.2.1.1
trapHostAddressType The type of Internet address by which the trap host is reachable.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.16177.2.1.5.1.1.2.1.2
trapHostAddress The IP address or Domain name for the trap host.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.2.1.5.1.1.2.1.3
trapHostRowStatus This object indicates the status of this table entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.16177.2.1.5.1.1.2.1.4

The status for alarm triggers.

alarmStatusEntry row .1.3.6.1.4.1.16177.2.1.5.2.4.1

An entry containing information about a specific alarm trigger.

Indexes

alarmStatusTriggerId

Column	Syntax	OID
alarmStatusTriggerId The id of alarm trigger	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.5.2.4.1.1
alarmStatusTriggerType A text string containing description about the trigger type	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.5.2.4.1.2
alarmStatusTriggerEnabled Indicates if the trigger is enabled or not	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.16177.2.1.5.2.4.1.3
alarmStatusTriggerStatus The actual alarm status for the trigger	Enumeration Enumerated Values: 1 warning 2 ok	.1.3.6.1.4.1.16177.2.1.5.2.4.1.4
alarmStatusTriggerStatusReason A text string containing status reason	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.16177.2.1.5.2.4.1.5