TROPIC-SYSTEM-MIB Table View

.

tnSysNtpServerEntry row .1.3.6.1.4.1.7483.2.1.1.2.8.1.1

.

Indexes

tnSysNtpServerIndex

Column	Syntax	OID
tnSysNtpServerIndex For the 1830 PSS-32, the maximum number of supported servers is 8.	Unsigned32 Constraints: range: 1-8	.1.3.6.1.4.1.7483.2.1.1.2.8.1.1.1
tnSysNtpServerIpAddress This attribute is configurable only when the row status has been set to createAndGo.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.8.1.1.2
tnSysNtpServerRowStatus .	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.8.1.1.3
tnSysNtpServerKeyIndex .	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.8.1.1.4
tnSysNtpServerInetAddress Indicates the IPv6 address of the NTP Server.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.8.1.1.5
tnSysNtpServerInetAddressType The value specifies the type of Internet address stored in tnSysNtpServerInetAddress.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7483.2.1.1.2.8.1.1.6

.

tnSnmpTargetAddrEntry row .1.3.6.1.4.1.7483.2.1.1.2.9.1.1

.

Indexes

No indexes recorded

Column	Syntax	OID
tnSnmpTargetAddrNmsStationGroupId .	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.9.1.1.1
tnSnmpTargetAddrTrapGroupId .	Enumerationr/w Enumerated Values: 1 allOtherData 2 pmData	.1.3.6.1.4.1.7483.2.1.1.2.9.1.1.2
tnSnmpTargetAddrDisableTrap Indicates the destination based trap disable mechanism feature is on.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.9.1.1.3

.

tnSshKeyEntry row .1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1

.

Indexes

tnSshKeyTypeIndex

Column	Syntax	OID
tnSshKeyTypeIndex The secure shell key type.	Enumeration Enumerated Values: 1 dsa 2 rsa 3 ecdsa 4 ed25519	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.1
tnSshPublicKey The secure shell public key.	OctetString Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.2
tnSshPublicKey1 The secure shell public key1.	OctetString Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.3
tnSshEcdsaPublicKey The secure Ecdsa public key.	OctetString Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.4
tnSshEcdsaPublicKey1 The secure Ecdsa public key1.	OctetString Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.5
tnSshEd25519PublicKey The secure Ed25519 public key.	OctetString Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.6
tnSshEd25519PublicKey1 The secure Ed25519 public key1.	OctetString Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.15.4.2.1.7

Table of IP ACL pattern.  An ACL pattern is a
set of packet field descriptors that can be
tested against a packet.  For a pattern to
match, each of its field descriptors must fit
the data in the packet.

tnSysIpAclPatternEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.3.1

.

Indexes

tnSysIpAclPatternID

Column	Syntax	OID
tnSysIpAclPatternID The identifier of the ACL pattern to be created. It could be either an integer in the range of (1-4000) or a string of up to 30 case-sensitive alphanumeric characters, where the first character is always a letter, which…	OctetString Constraints: range: 1-30	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.1
tnSysIpAclPatternAction Action to be taken on packets matching the specified ACL pattern. Valid values are: pass - allow the packet if it matches all the pattern descriptors; block - disallow the packet if it doesn't match al…	Enumerationr/w Enumerated Values: 1 pass 2 block 3 log	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.2
tnSysIpAclPatternICMPERROR ICMP error reporting behavior for blocked packets. If no icmpError value is specified, the behavior will be determined by the system default setting. Valid values are: true - send ICMP error for blocked packets false…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.3
tnSysIpAclPatternSrcAddr Source IP address. It can be specified explicitly to match only packets that originate from a particular address or can be used along with the SrcPrefix parameter to specify a range of supported originating IP addresse…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.4
tnSysIpAclPatternSrcPrefix Source IP mask prefix. It's the reverse of a subnet mask, where 0 indicates a position that must be matched and 1 indicates a position that does not matter. If the SrcAddr is specified and the SrcPrefix is unspecified…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.5
tnSysIpAclPatternDestAddr Destination IP address. It can be specified explicitly to match only packets that originate from a particular address or can be used along with the DestPrefix parameter to specify a range of supported destination IP ad…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.6
tnSysIpAclPatternDestPrefix Destination IP Mask Prefix. It's the reverse of a subnet mask, where 0 indicates a position that must be matched and 1 indicates a position that does not matter. If the DestAddr is specified and the DestPrefix is unsp…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.7
tnSysIpAclPatternDestPort TCP/UDP destination port.When rangeEnd not zero, it is used as range start. It is applicable only when the IP Protocol is TCP or UDP. Some of the commonly used ports are: 20 FTP-Data TCP File Transfer Protocol […	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.8
tnSysIpAclPatternIpProtocol IP Protocol. It can be specified by explicit protocol number (Integer, 0 to 255) or by keyword. Some common protocol types are listed below: ICMP - IP protocol is ICMP (1) IPIP - IP protocol i…	OctetStringr/w	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.9
tnSysIpAclPatternIpFragment IP Fragmentation. True means that the filtering is done on all fragments, not just on the initial one (assuming the following ones are ok). Valid values are: true - pattern is an IP false - pattern is not an IP fragm…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.10
tnSysIpAclPatternIcmpType ICMP Type identifier. It is applicable only when IPPROTOCOL is ICMP. If specified, the pattern will match only packets with this exact ICMP type. Some of the most commonly used ICMP types are: 0 Echo Reply [R…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.11
tnSysIpAclPatternIcmpCode ICMP code field. It is applicable only when IP protocol is ICMP and is used along with certain ICMP types to further specify the message type. It must also specify the ICMP type when setting this parameter. If specifi…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.12
tnSysIpAclPatternTcpEstablish TCP established flag. It matches a packet depending on whether the TCP flags in the IP header correspond to the established state. It is applicable only when IP Protocol is TCP. Valid values are: true - TCP flags co…	Enumerationr/w Enumerated Values: 1 true 2 false 3 local	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.13
tnSysIpAclPatternRowStatus The status of pattern. Set to 4 (createAndGo) to add pattern. Set to 6 (destroy) to remove the pattern.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.14
tnSysIpAclPatternSrcPort TCP/UDP source port. When rangeEnd not zero, it is used as range start. It is applicable only when the IP Protocol is TCP or UDP. Some of the commonly used ports are: 20 FTP-Data TCP File Transfer…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.15
tnSysIpAclPatternSystemDefault Indicates if ACL pattern is added by the system or a user. Valid values are: true - ACL pattern is added by the system. false - ACL pattern is added by the user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.16
tnSysIpAclPatternSrcPortRangeEnd TCP/UDP source port range end.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.17
tnSysIpAclPatternDestPortRangeEnd TCP/UDP destination port range end.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.3.1.18

An ACL filter is an ordered list of patterns.
A filter consists of a sorted list of (index,
pattern) pairs, where the index indicates the
relative position on the list and the pattern
indicates the pattern identifier.  Up to 100
filters may be defined on the system, and each
filter may contain up to 256 (index, pattern)
pairs.

tnSysIpAclFilterEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.5.1

.

Indexes

tnSysIpAclFilterID tnSysIpAclFilterPatternIndex

Column	Syntax	OID
tnSysIpAclFilterID Identifier for the ACL filter being defined. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where the first character is always a letter, which un…	OctetString Constraints: range: 1-30	.1.3.6.1.4.1.7483.2.1.1.2.17.5.1.1
tnSysIpAclFilterPatternIndex The values of 1 to 256 represent the insertion point for the specified pattern on the filter list. If there is already a pattern defined at the specified index, the new pattern entry will replace the previous one. The…	Integer32 Constraints: range: 0-256	.1.3.6.1.4.1.7483.2.1.1.2.17.5.1.2
tnSysIpAclFilterPatternID The identifier of the ACL pattern being added to or removed from the specified filter. It could be either an integer in the range of (1-4000) or a string of up to 30 case-sensitive alphanumeric characters, where the fi…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.5.1.3
tnSysIpAclFilterStatCount Packet match counter. It is incremented whenever a packet matches the specified ACL pattern in the filter. This counter will be incremented regardless of the provisioned action on that pattern.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.17.5.1.4
tnSysIpAclFilterRowStatus Action to take on the specified filter. The operator could add or remove a pattern from a specified filter. Set to 4 (createAndGo) to add pattern in the filter. Set to 6 (destroy) to remove the pattern in the filter.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.5.1.5
tnSysIpAclFilterSystemDefault Indicates if ACL filter is added by the system or a user. Valid values are: true - ACL filter is added by the system. false - ACL filter is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.5.1.6

The IP ACL interface table is used to associate
or disassociate filters with particular physical
network interfaces (but not logical sub-interfaces).
Two filters may be associated with each interface,
one receive and one transmit.  The receive and
transmit filters on an interface may be
independently enabled and disabled on that
interface without disassociating the specific
filter numbers.

tnSysIpAclInterfaceEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.7.1

.

Indexes

IF-MIBifIndex tnSysIpAclInterfaceFilterDir

Column	Syntax	OID
tnSysIpAclInterfaceFilterDir Direction on the specified network interface to which the IP ACL filter will be associated.	Enumeration Enumerated Values: 1 rx 2 tx	.1.3.6.1.4.1.7483.2.1.1.2.17.7.1.1
tnSysIpAclInterfaceFilterID Identifier for the ACL filter being associated with the specified interface and direction. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where t…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.7.1.2
tnSysIpAclInterfaceFilterEnable Enable or disable the IP ACL filter associated with the specified interface and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.7.1.3
tnSysIpAclInterfaceFilterRowStatus The status of Interface Filter. Set to 4 (createAndGo) to add filter in the interface. Set to 6 (destroy) to remove the filter in the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.7.1.4
tnSysIpAclInterfaceSystemDefault Indicates if ACL interface added by the system or a user. Valid values are: true - ACL interface is added by the system. false - ACL interface is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.7.1.5
tnSysIpAclInterfaceFilterLog Enable or disable the IP ACL filter logging on specified interface and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.7.1.6

The IP ACL NetIf table is used to associate or
disassociate filters with particular NetIf.  Two
filters may be associated with each NetIf, one
receive and one transmit.  The receive and transmit
filters on an NetIf may be independently enabled
and disabled on that NetIf without disassociating
the specific filter numbers.

tnSysIpAclNetIfFilterEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.9.1

.

Indexes

TROPIC-L1SERVICE-MIBtnNetIfIndex tnSysIpAclNetIfFilterDir

Column	Syntax	OID
tnSysIpAclNetIfFilterDir Direction on the specified NetIf to which the IP ACL filter will be associated.	Enumeration Enumerated Values: 1 rx 2 tx	.1.3.6.1.4.1.7483.2.1.1.2.17.9.1.1
tnSysIpAclNetIfFilterRowStatus The status of NetIf Filter. Set to 4 (createAndGo) to add filter in the interface. Set to 6 (destroy) to remove the filter in the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.9.1.2
tnSysIpAclNetIfFilterID Identifier for the ACL filter being associated with the specified NetIf and direction. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where the …	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.9.1.3
tnSysIpAclNetIfFilterEnable Enable or disable the IP ACL filter associated with the specified NetIf and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.9.1.4
tnSysIpAclNetIfFilterSystemDefault Indicates if ACL NetIf is added by the system or a user. Valid values are: true - ACL interface is added by the system. false - ACL interface is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.9.1.5

Table of IPV6 ACL pattern.  An ACL pattern is a
set of packet field descriptors that can be
tested against a packet.  For a pattern to
match, each of its field descriptors must fit
the data in the packet.

tnSysIpAclIpv6PatternEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.11.1

.

Indexes

tnSysIpAclIpv6PatternID

Column	Syntax	OID
tnSysIpAclIpv6PatternID The identifier of theIpv6 ACL pattern to be created. It could be either an integer in the range of (1-4000) or a string of up to 30 case-sensitive alphanumeric characters, where the first character is always a letter, w…	OctetString Constraints: range: 1-30	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.1
tnSysIpAclIpv6PatternAction Action to be taken on packets matching the specified Ipv6ACL pattern. Valid values are: pass - allow the packet if it matches all the pattern descriptors; block - disallow the packet if it doesn't match all the patter…	Enumerationr/w Enumerated Values: 1 pass 2 block 3 log	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.2
tnSysIpAclIpv6PatternICMPV6ERROR ICMPV6 error reporting behavior for blocked packets. If no icmpV6Error value is specified, the behavior will be determined by the system default setting. Valid values are: true - send ICMPV6 error for blocked packets…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.3
tnSysIpAclIpv6PatternSrcAddr Source IPV6 address. It can be specified explicitly to match only packets that originate from a particular address or can be used along with the SrcPrefixLen parameter to specify a range of supported originating IPV6 a…	INET-ADDRESS-MIBInetAddressIPv6r/w Type Constraints: range: 16	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.4
tnSysIpAclIpv6PatternSrcPrefixLen Denotes the length of source IPV6 address prefix. A value of n corresponds to an IP address maskthat has n contiguous1-bits from the most significant bit (MSB), with all other bits set to 0	INET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.5
tnSysIpAclIpv6PatternDestAddr Destination IPV6 address. It can be specified explicitly to match only packets that originate from a particular address or can be used along with the DestPrefixLen parameter to specify a range of supported destination …	INET-ADDRESS-MIBInetAddressIPv6r/w Type Constraints: range: 16	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.6
tnSysIpAclIpv6PatternDestPrefixLen Denotes the length of destination IPV6 address prefix. A value of n corresponds to an IP address maskthat has n contiguous1-bits from the most significant bit (MSB), with all other bits set to 0	INET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.7
tnSysIpAclIpv6PatternIpProtocol IP Protocol. It can be specified by explicit protocol number (Integer, 0 to 255) or by keyword. Some common protocol types are listed below: ICMPv6 - IP protocol is ICMPv6 (58) IPIP - IP protocol is IPIP (41) TCP …	OctetStringr/w	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.8
tnSysIpAclIpv6PatternIcmpType ICMPV6 Type identifier. If specified, the pattern will match only packets with this exact ICMPV6 type. Some of the most commonly used ICMP types are: 1 Destination Unreachable [RFC2463] 2 Packet Too Big 3 Time…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.9
tnSysIpAclIpv6PatternIcmpCode ICMPV6code field. It is used along with certain ICMPV6 types to further specify the message type. For example, some of the codes used with ICMPv6 Type 1 (Destination Unreachable) are 0 no route to destination 1 …	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.10
tnSysIpAclIpv6PatternSrcPort TCP/UDP source port. When rangeEnd not zero, it is used as range start.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.11
tnSysIpAclIpv6PatternDestPort TCP/UDP destination port. When rangeEnd not zero, it is used as range start.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.12
tnSysIpAclIpv6PatternIpFragment IP Fragmentation. True means that the filtering is done on all fragments, not just on the initial one (assuming the following ones are ok). Valid values are: true - pattern is an IP false - pattern is not an IP fragm…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.13
tnSysIpAclIpv6PatternTcpEstablish TCP established flag. It matches a packet depending on whether the TCP flags in the IP header correspond to the established state. Valid values are: true - TCP flags correspond to established state false - TCP flags …	Enumerationr/w Enumerated Values: 1 true 2 false 3 local	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.14
tnSysIpAclIpv6PatternSystemDefault Indicates if ACLIPV6 pattern is added by the system or a user. Valid values are: true - ACL pattern is added by the system. false - ACL pattern is added by the user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.15
tnSysIpAclIpv6PatternRowStatus The status of pattern. Set to 4 (createAndGo) to add pattern. Set to 6 (destroy) to remove the pattern.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.16
tnSysIpAclIpv6PatternSrcPortRangeEnd TCP/UDP source port range end.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.17
tnSysIpAclIpv6PatternDestPortRangeEnd TCP/UDP destination port range end.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.17.11.1.18

An ACL filter is an ordered list of patterns.
A filter consists of a sorted list of (index,
pattern) pairs, where the index indicates the
relative position on the list and the pattern
indicates the pattern identifier.  Up to 100
filters may be defined on the system, and each
filter may contain up to 256 (index, pattern)
pairs.

tnSysIpAclIpv6FilterEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.13.1

.

Indexes

tnSysIpAclIpv6FilterID tnSysIpAclIpv6FilterPatternIndex

Column	Syntax	OID
tnSysIpAclIpv6FilterID Identifier for the ACL filter being defined. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where the first character is always a letter, which un…	OctetString Constraints: range: 1-30	.1.3.6.1.4.1.7483.2.1.1.2.17.13.1.1
tnSysIpAclIpv6FilterPatternIndex The values of 1 to 256 represent the insertion point for the specified pattern on the filter list. If there is already a pattern defined at the specified index, the new pattern entry will replace the previous one. The…	Integer32 Constraints: range: 0-256	.1.3.6.1.4.1.7483.2.1.1.2.17.13.1.2
tnSysIpAclIpv6FilterPatternID The identifier of the ACL pattern being added to or removed from the specified filter. It could be either an integer in the range of (1-4000) or a string of up to 30 case-sensitive alphanumeric characters, where the fi…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.13.1.3
tnSysIpAclIpv6FilterStatCount Packet match counter. It is incremented whenever a packet matches the specified ACL pattern in the filter. This counter will be incremented regardless of the provisioned action on that pattern.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.17.13.1.4
tnSysIpAclIpv6FilterRowStatus Action to take on the specified filter. The operator could add or remove a pattern from a specified filter. Set to 4 (createAndGo) to add pattern in the filter. Set to 6 (destroy) to remove the pattern in the filter.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.13.1.5
tnSysIpAclIpv6FilterSystemDefault Indicates if ACL filter is added by the system or a user. Valid values are: true - ACL filter is added by the system. false - ACL filter is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.13.1.6

The IP ACL interface table is used to associate
or disassociate filters with particular physical
network interfaces (but not logical sub-interfaces).
Two filters may be associated with each interface,
one receive and one transmit.  The receive and
transmit filters on an interface may be
independently enabled and disabled on that
interface without disassociating the specific
filter numbers.

tnSysIpAclIpv6InterfaceEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.15.1

.

Indexes

IF-MIBifIndex tnSysIpAclIpv6InterfaceFilterDir

Column	Syntax	OID
tnSysIpAclIpv6InterfaceFilterDir Direction on the specified network interface to which the IP ACL filter will be associated.	Enumeration Enumerated Values: 1 rx 2 tx	.1.3.6.1.4.1.7483.2.1.1.2.17.15.1.1
tnSysIpAclIpv6InterfaceFilterID Identifier for the ACL filter being associated with the specified interface and direction. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where t…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.15.1.2
tnSysIpAclIpv6InterfaceFilterEnable Enable or disable the IP ACL filter associated with the specified interface and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.15.1.3
tnSysIpAclIpv6InterfaceFilterRowStatus The status of Interface Filter. Set to 4 (createAndGo) to add filter in the interface. Set to 6 (destroy) to remove the filter in the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.15.1.4
tnSysIpAclIpv6InterfaceSystemDefault Indicates if ACL interface added by the system or a user. Valid values are: true - ACL interface is added by the system. false - ACL interface is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.15.1.5
tnSysIpAclIpv6InterfaceFilterLog Enable or disable the IPV6 ACL filter logging on specified interface and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.15.1.6

The IP ACL NetIf table is used to associate or
disassociate filters with particular NetIf.  Two
filters may be associated with each NetIf, one
receive and one transmit.  The receive and transmit
filters on an NetIf may be independently enabled
and disabled on that NetIf without disassociating
the specific filter numbers.

tnSysIpv6AclNetIfFilterEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.17.1

.

Indexes

TROPIC-L1SERVICE-MIBtnNetIfIndex tnSysIpv6AclNetIfFilterDir

Column	Syntax	OID
tnSysIpv6AclNetIfFilterDir Direction on the specified NetIf to which the IP ACL filter will be associated.	Enumeration Enumerated Values: 1 rx 2 tx	.1.3.6.1.4.1.7483.2.1.1.2.17.17.1.1
tnSysIpv6AclNetIfFilterRowStatus The status of NetIf Filter. Set to 4 (createAndGo) to add filter in the interface. Set to 6 (destroy) to remove the filter in the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.17.1.2
tnSysIpv6AclNetIfFilterID Identifier for the ACL filter being associated with the specified NetIf and direction. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where the …	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.17.1.3
tnSysIpv6AclNetIfFilterEnable Enable or disable the IP ACL filter associated with the specified NetIf and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.17.1.4
tnSysIpv6AclNetIfFilterSystemDefault Indicates if ACL NetIf is added by the system or a user. Valid values are: true - ACL interface is added by the system. false - ACL interface is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.17.1.5

The IP ACL EthIf table is used to associate or
disassociate filters with particular EthIf.  Two
filters may be associated with each EthIf, one
receive and one transmit.  The receive and transmit
filters on an EthIf may be independently enabled
and disabled on that EthIf without disassociating
the specific filter numbers.

tnSysIpAclEthIfFilterEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.19.1

.

Indexes

TROPIC-L1SERVICE-MIBtnEthIfIndex tnSysIpAclEthIfFilterDir

Column	Syntax	OID
tnSysIpAclEthIfFilterDir Direction on the specified EthIf to which the IP ACL filter will be associated.	Enumeration Enumerated Values: 1 rx 2 tx	.1.3.6.1.4.1.7483.2.1.1.2.17.19.1.1
tnSysIpAclEthIfFilterRowStatus The status of EthIf Filter. Set to 4 (createAndGo) to add filter in the interface. Set to 6 (destroy) to remove the filter in the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.19.1.2
tnSysIpAclEthIfFilterID Identifier for the ACL filter being associated with the specified EthIf and direction. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where the …	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.19.1.3
tnSysIpAclEthIfFilterEnable Enable or disable the IP ACL filter associated with the specified EthIf and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.19.1.4
tnSysIpAclEthIfFilterSystemDefault Indicates if ACL EthIf is added by the system or a user. Valid values are: true - ACL interface is added by the system. false - ACL interface is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.19.1.5

The IPV6 ACL EthIf table is used to associate or
disassociate filters with particular EthIf.  Two
filters may be associated with each EthIf, one
receive and one transmit.  The receive and transmit
filters on an EthIf may be independently enabled
and disabled on that EthIf without disassociating
the specific filter numbers.

tnSysIpv6AclEthIfFilterEntry row .1.3.6.1.4.1.7483.2.1.1.2.17.21.1

.

Indexes

TROPIC-L1SERVICE-MIBtnEthIfIndex tnSysIpv6AclEthIfFilterDir

Column	Syntax	OID
tnSysIpv6AclEthIfFilterDir Direction on the specified EthIf to which the IP ACL filter will be associated.	Enumeration Enumerated Values: 1 rx 2 tx	.1.3.6.1.4.1.7483.2.1.1.2.17.21.1.1
tnSysIpv6AclEthIfFilterRowStatus The status of EthIf Filter. Set to 4 (createAndGo) to add filter in the interface. Set to 6 (destroy) to remove the filter in the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.17.21.1.2
tnSysIpv6AclEthIfFilterID Identifier for the ACL filter being associated with the specified EthIf and direction. It could be either an integer in the range of (100-199) or a string of up to 30 case-sensitive alphanumeric characters, where the f…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.7483.2.1.1.2.17.21.1.3
tnSysIpv6AclEthIfFilterEnable Enable or disable the IPV6 ACL filter associated with the specified EthIf and direction.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.1.1.2.17.21.1.4
tnSysIpv6AclEthIfFilterSystemDefault Indicates if ACL EthIf is added by the system or a user. Valid values are: true - ACL interface is added by the system. false - ACL interface is added by a user.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.17.21.1.5

.

tnSysNtpServerIdStatsEntry row .1.3.6.1.4.1.7483.2.1.1.2.18.1.1

.

Indexes

tnSysNtpServerIdStatsIndex

Column	Syntax	OID
tnSysNtpServerIdStatsIndex For the 1830 PSS-32. The maximum number of supported NTP servers is 8.	Unsigned32 Constraints: range: 1-8	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.1
tnSysNtpServerIdStatsSelect Character to be displayed is one of the following: '*' - selected reference '+' - member of the alternate references ' ' - disqualified.	OctetString Constraints: range: 0-2	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.2
tnSysNtpServerIdStatsIp NTP server IP address.	OctetString Constraints: range: 0-48	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.3
tnSysNtpServerIdStatsRefId NTP reference ID.	OctetString Constraints: range: 0-48	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.4
tnSysNtpServerIdStatsStrtm Level of reference, from 1 - 16.	OctetString Constraints: range: 0-3	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.5
tnSysNtpServerIdStatsClockType Clock type: 'u' - unicast 'b' - broadcast 'l' - local.	OctetString Constraints: range: 0-2	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.6
tnSysNtpServerIdStatsPoll Polling interval in log base 2 seconds.	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.7
tnSysNtpServerIdStatsReach 8 bit octal number representing success of last 8 attempts.	OctetString Constraints: range: 0-4	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.8
tnSysNtpServerIdStatsDelay Round trip delay to the reference server.	OctetString Constraints: range: 0-12	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.9
tnSysNtpServerIdStatsOffset .	OctetString Constraints: range: 0-12	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.10
tnSysNtpServerIdStatsJitter .	OctetString Constraints: range: 0-12	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.11
tnSysNtpServerIdStatsKeyIndex .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.18.1.1.12

.

tnSysNtpServerAuthenticationEntry row .1.3.6.1.4.1.7483.2.1.1.2.20.2.1

.

Indexes

tnSysNtpServerAuthenticationKeyIndex

Column	Syntax	OID
tnSysNtpServerAuthenticationKeyIndex NTP server authentication key index.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.7483.2.1.1.2.20.2.1.1
tnSysNtpServerAuthenticationRowStatus Status of this NTP server. Supported values: 1 - active 4 - createAndGo 6 - destroy.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.20.2.1.2
tnSysNtpServerAuthenticationKeyType NTP server authentication key type.	Enumerationr/w Enumerated Values: 1 sha1 2 md5	.1.3.6.1.4.1.7483.2.1.1.2.20.2.1.3
tnSysNtpServerAuthenticationKey NTP server authentication key.	OctetStringr/w Constraints: range: 0-500	.1.3.6.1.4.1.7483.2.1.1.2.20.2.1.4

.

tnNeDiscoveryEntry row .1.3.6.1.4.1.7483.2.1.1.2.21.2.1

.

Indexes

tnNeDiscoveryIndex

Column	Syntax	OID
tnNeDiscoveryIndex Unique name given by the NMS.	OctetString Constraints: range: 1-28	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.1
tnNeDiscoveryFilename .	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.2
tnNeDiscoveryControl Controls the discovery, i.e., starts or aborts it.	Enumerationr/w Enumerated Values: 1 noCmd 2 start 3 abort	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.3
tnNeDiscoveryStatus The discovery status.	Enumeration Enumerated Values: 1 idle 2 inProgress 3 completedSuccessfully 4 failed 5 aborted	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.4
tnNeDiscoveryErrorCode The discovery error code.	Enumeration Enumerated Values: 1 noError 2 unknown 3 timeout 4 serverError 5 networkError 6 fileSystemError 7 systemNotReady	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.5
tnNeDiscoveryServerIp The discovery server IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.6
tnNeDiscoveryServerProtocol The discovery server protocol.	TROPIC-TCAluWdmNewTransferProtocolr/w Type Values: 1 ftp 2 sftp 3 http 4 https	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.7
tnNeDiscoveryServerUserId The user ID used to access the server.	OctetStringr/w Constraints: range: 1-128	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.8
tnNeDiscoveryServerPassword The password used to access the server. When read, this attribute will return an empty string if the password has not been set and '********' if it has been set.	OctetStringr/w Constraints: range: 1-128	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.9
tnNeDiscoveryServerTimeOut Timeout from NMS for the discovery request.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.10
tnNeDiscoveryRowStatus The row status of this discovery.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.11
tnNeDiscoveryServerInetAddressType The value specifies the type of Internet address stored in tnNeDiscoveryServerInetAddress.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.12
tnNeDiscoveryServerInetAddress Indicates the IPv6 address of the log server.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.13
tnNeDiscoveryDeltaFilenamedeprecated .	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.14
tnNeDiscoveryDeltaFileFlag Delta File Flag.	Enumerationr/w Enumerated Values: 1 eqptSyncEnable 2 eqptSyncDisable 3 tpSyncEnable 4 tpSyncDisable 5 sncSyncEnable 6 sncSyncDisable 7 tlSyncEnable 8 tlSyncDisable 9 pgSyncEnable 10 pgSyncDisable 11 syncTransfer 12 syncClear 13 syncDisable 14 eqptSyncTransfer 15 tpSyncTransfer 16 sncSyncTransfer 17 tlSyncTransfer 18 pgSyncTransfer 19 syncTrapEnable 20 syncTrapDisable 21 syncTrapTransfer	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.15
tnNeDiscoveryDeltaSyncStatus Active sync status.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.16
tnNeDiscoveryPort .	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.7483.2.1.1.2.21.2.1.17

.

tnSysOtdrScanSystemProfileEntry row .1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1

.

Indexes

tnSysOtdrScanSystemProfileId

Column	Syntax	OID
tnSysOtdrScanSystemProfileId Unique identifier for the profile. Range is from 1 to 9.	Integer32 Constraints: range: 1-9	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.1
tnSysOtdrScanSystemProfileDescription Describes the scan profile.	OctetStringr/w Constraints: range: 0-80	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.2
tnSysOtdrScanSystemProfileWaveLength The wavelength used for the OTDR scan. The wavelength is 1610 nm, and is not configurable.	nanometersSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.3
tnSysOtdrScanSystemProfilePulseLength Length of the pulse. Current values: 5, 10, 30, 100, 300, 1000, 3000, 10000, and 20000.	nanosecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.4
tnSysOtdrScanSystemProfileRange The range of the span that is being probed in meters. Current values: 500, 1000, 2000, 5000, 10000, 20000, 40000, 80000, 160000 and 260000.	metersSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.5
tnSysOtdrScanSystemProfileResolution Distance resolution of the OTDR scan. Current values: 40, 80, 160, 320, 640, 1200, 2500, 5000, 10000, 20000, 40000, 80000, and 160000.	millimetersSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.6
tnSysOtdrScanSystemProfileAvgTime Signal averaging time for a scan range. Current range: 5 to 300.	secondsUnsigned32r/w Constraints: range: 5-300	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.7
tnSysOtdrScanSystemProfileEventThreshold Sys Otdr Scan Event Threshold. Current range: 5 to 100.	mBSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.8
tnSysOtdrScanSystemProfileIOR Sys Otdr Scan IOR. Current range: 1400 to 1600.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.1.2.1.9

.

tnSysOtdrScanSystemProfileMEntry row .1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1

.

Indexes

tnSysOtdrScanSystemProfileMId

Column	Syntax	OID
tnSysOtdrScanSystemProfileMId Unique identifier for the profile. Range is from 1 to 7.	Integer32 Constraints: range: 1-7	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.1
tnSysOtdrScanSystemProfileMDescription Describes the scan profile.	OctetStringr/w Constraints: range: 0-80	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.2
tnSysOtdrScanSystemProfileMWaveLength The wavelength used for the OTDR scan. The wavelength is 1610 nm, and is not configurable.	nanometersSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.3
tnSysOtdrScanSystemProfileMPulseLength Length of the pulse. Current values: 5, 10, 30, 100, 300, 1000, 3000, 10000, and 20000.	nanosecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.4
tnSysOtdrScanSystemProfileMRange The range of the span that is being probed in meters. Current values: 500, 1000, 2000, 5000, 10000, 20000, 40000, 80000, 160000 and 260000.	metersSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.5
tnSysOtdrScanSystemProfileMResolution Distance resolution of the OTDR scan. Current values: 40, 80, 160, 320, 640, 1200, 2500, 5000, 10000, 20000, 40000, 80000, and 160000.	millimetersSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.6
tnSysOtdrScanSystemProfileMAvgTime Signal averaging time for a scan range. Current range: 5 to 300.	secondsUnsigned32r/w Constraints: range: 5-300	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.7
tnSysOtdrScanSystemProfileMEventThreshold Sys Otdr Scan Event Threshold. Current range: 5 to 100.	mBSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.8
tnSysOtdrScanSystemProfileMIOR Sys Otdr Scan IOR. Current range: 1400 to 1600.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.22.3.2.1.9

.

tnClusterEntry row .1.3.6.1.4.1.7483.2.1.1.2.23.1.1

.

Indexes

tnClusterFarEndNode

Column	Syntax	OID
tnClusterRowStatus .	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.23.1.1.1
tnClusterFarEndNode .	OctetString	.1.3.6.1.4.1.7483.2.1.1.2.23.1.1.2
tnClusterIpAddress .	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.23.1.1.3
tnClusterlinkStatus Cluster link status.	Enumerationr/w Enumerated Values: 1 up 2 down 3 unknown	.1.3.6.1.4.1.7483.2.1.1.2.23.1.1.4
tnClusterInetAddressType The value specifies the type of Internet address stored in Cluster.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7483.2.1.1.2.23.1.1.5
tnClusterInetAddress Indicates the IPv6 address of the Cluster.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.23.1.1.6

.

tnLicenseEntityEntry row .1.3.6.1.4.1.7483.2.1.1.2.33.1.1

.

Indexes

tnLicenseEntity

Column	Syntax	OID
tnLicenseEntity .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.33.1.1.1
tnLicenseEntityRefreshSet .	TROPIC-TCTnCommandr/w Type Values: 1 noCmd 2 execute	.1.3.6.1.4.1.7483.2.1.1.2.33.1.1.2
tnLicenseEntityNumberInUse Number in Use.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.33.1.1.3
tnLicenseEntityNumberExceedAvail Number Exceeding available.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.33.1.1.4
tnLicenseEntityEntitlementNeeded Entitlement needed by NE.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.33.1.1.5

.

tnLicenseEntitlementEntry row .1.3.6.1.4.1.7483.2.1.1.2.33.2.1

.

Indexes

tnLicenseEntitlementCategoryID tnLicenseEntitlementEntries

Column	Syntax	OID
tnLicenseEntitlementCategoryID .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.33.2.1.1
tnLicenseEntitlementEntries .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.33.2.1.2
tnLicenseEntitlementDetails The format will be cardName_LineRate_RequestedCount_MissingCount.	OctetString Constraints: range: 0-2047	.1.3.6.1.4.1.7483.2.1.1.2.33.2.1.3

KeyStore Service Management.

tnSysKeyStoreServiceEntry row .1.3.6.1.4.1.7483.2.1.1.2.34.1.1

.

Indexes

tnSysKeyStoreNameIndex tnSysKeyStoreTypeIndex

Column	Syntax	OID
tnSysKeyStoreNameIndex KeyStore name.	Enumeration Enumerated Values: 1 invalid 2 ztp 3 internecomm 4 system	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.1
tnSysKeyStoreTypeIndex KeyStore type.	Enumeration Enumerated Values: 1 invalid 2 trustAnchor 3 privateKey	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.2
tnSysKeyStoreTransServerCommand noCmd - No operation upload - Upload file to remote server download - Only download, not install. install - Install the former downloaded restoreToDefault - Clear for…	Enumerationr/w Enumerated Values: 1 noCmd 2 upload 3 download 4 install 5 restoreToDefault 6 downloadThenInstall 7 clear	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.3
tnSysKeyStoreTransServerProtocol KeyStore transfer server protocol: invalid - Not configed yet https - Use https protocol sftp - Use sftp protocol.	Enumerationr/w Enumerated Values: 1 invalid 2 https 3 sftp	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.4
tnSysKeyStoreTransServerHost Domain or ip address of URI. https used only.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.5
tnSysKeyStoreTransServerPort Port of URI. https used only.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.6
tnSysKeyStoreTransServerLocation For https: location of URI; for others: path on server.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.7
tnSysKeyStoreTransServerUserId Username for authentication.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.8
tnSysKeyStoreTransServerPassword Password for authentication.	OctetStringr/w Constraints: range: 0-256	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.9
tnSysKeyStoreTransServerInetAddressType .	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.10
tnSysKeyStoreTransServerInetAddress .	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.11
tnSysKeyStoreServiceStatus Last operation status: none - No command installed - Installed successfully downloaded - Downloaded successfully in-progress - Processing and need to wait transferfail - File transfer fail formaterror - F…	Enumeration Enumerated Values: 1 none 2 installed 3 downloaded 4 in-progress 5 transferfail 6 formaterror	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.12
tnSysKeyStoreServerLastTransferTime The last transfer (download/upload) time.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.13
tnSysKeyStoreTransServerURI URI.	OctetStringr/w Constraints: range: 0-511	.1.3.6.1.4.1.7483.2.1.1.2.34.1.1.14

KeyStore Certificate Information.

tnSysKeyStoreCertInfoEntry row .1.3.6.1.4.1.7483.2.1.1.2.34.2.1

.

Indexes

tnSysKeyStoreCertRepositoryIndex tnSysKeyStoreCertIndex

Column	Syntax	OID
tnSysKeyStoreCertRepositoryIndex KeyStore certificate repository.	Enumeration Enumerated Values: 1 invalid 2 trustAnchorInstalledOfZtp 3 trustAnchorDownLoadedOfZtp 4 trustAnchorInstalledOfSystem 5 trustAnchorDownLoadedOfSystem	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.1
tnSysKeyStoreCertIndex .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.2
tnSysKeyStoreCertVersion Certificate version.	OctetString Constraints: range: 0-31	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.3
tnSysKeyStoreCertSerialNumber Certificate serial number.	OctetString Constraints: range: 0-63	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.4
tnSysKeyStoreCertSignatureAlgorithm Certificate signature algorithm.	OctetString Constraints: range: 0-63	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.5
tnSysKeyStoreCertIssuer Certificate issuer.	OctetString Constraints: range: 0-511	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.6
tnSysKeyStoreCertValidity Certificate validity.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.7
tnSysKeyStoreCertSubject Certificate subject.	OctetString Constraints: range: 0-511	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.8
tnSysKeyStoreCertSubjectPublicKeyInfo Certificate subject publicKey info.	OctetString Constraints: range: 0-63	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.9
tnSysKeyStoreCertKeyUsage Certificate key usage.	OctetString Constraints: range: 0-127	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.10
tnSysKeyStoreCertSubjectAlternativeName Certificate subject alternative name.	OctetString Constraints: range: 0-127	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.11
tnSysKeyStoreCertExtendedKeyUsage Certificate extended key usage.	OctetString Constraints: range: 0-127	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.12
tnSysKeyStoreCertBasicConstraints Certificate basic constraints.	OctetString Constraints: range: 0-127	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.13
tnSysKeyStoreCertSHA256Fingerprint Certificate SHA256 Fingerprint.	OctetString Constraints: range: 0-127	.1.3.6.1.4.1.7483.2.1.1.2.34.2.1.14

.

tnSysBgpPeerEntry row .1.3.6.1.4.1.7483.2.1.1.2.35.1.1

.

Indexes

tnSysBgpPeerIndex

Column	Syntax	OID
tnSysBgpPeerIndex .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.1
tnSysBgpPeerRowStatus .	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.2
tnSysBgpPeerInetAddressType The value specifies the type of Internet address stored in tnSysBgpPeerInetAddress.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.3
tnSysBgpPeerIp IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.4
tnSysBgpPeerInetAddress Indicates the IPv6 address.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.5
tnSysBgpPeerRemoteASN .	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.6
tnSysBgpPeerSecurityKey .	OctetStringr/w Constraints: range: 1-80	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.7
tnSysBgpPeerRouterId IP address.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.8
tnSysBgpPeerStatus .	Enumeration Enumerated Values: 1 idle 2 connect 3 active 4 openSent 5 openConfirm 6 established	.1.3.6.1.4.1.7483.2.1.1.2.35.1.1.9

.

tnSyslogServerEntry row .1.3.6.1.4.1.7483.2.1.1.2.37.1.1

.

Indexes

tnSyslogServerIndex

Column	Syntax	OID
tnSyslogServerIndex .	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.1
tnSyslogServerIpAddress .	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.2
tnSyslogServerPort .	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.3
tnSyslogServerFacility .	Enumerationr/w Enumerated Values: 1 kern 2 user 3 mail 4 daemon 5 auth 6 syslog 7 lpr 8 news 9 uucp 10 cron 11 authPriv 12 ftp 13 local0 14 local1 15 local2 16 local3 17 local4 18 local5 19 local6 20 local7	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.4
tnSyslogServerPriority .	Enumerationr/w Enumerated Values: 1 emergency 2 alert 3 critical 4 error 5 warning 6 notice 7 info 8 debug	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.5
tnSyslogServerEnabled .	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.6
tnSyslogServerInetAddress Indicates the IPv6 address of the Syslog Server.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.7
tnSyslogServerInetAddressType The value specifies the type of Internet address stored in tnSyslogServerInetAddress.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.8
tnSyslogServerProtocol Syslog Transmission Protocol.	Enumerationr/w Enumerated Values: 1 udp 2 tcp	.1.3.6.1.4.1.7483.2.1.1.2.37.1.1.9

.

tnHostKeyEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.1.1

.

Indexes

tnHostKeyModuleID tnHostKeyIndex

Column	Syntax	OID
tnHostKeyModuleID Host key string module ID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.1.1.2.39.1.1.1
tnHostKeyIndex Host key string key index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.1.1.2.39.1.1.2
tnHostKeyString1 Host key string 1.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.1.1.3
tnHostKeyString2 Host key string 2.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.1.1.4

.

tnSshPrivKeyEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.2.1

.

Indexes

tnSshPrivKeyModuleID

Column	Syntax	OID
tnSshPrivKeyModuleID Ssh Private key string module ID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.1.1.2.39.2.1.1
tnSshPrivKeyString1 Ssh Private key string 1.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.2.1.2
tnSshPrivKeyString2 Ssh Private key string 2.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.2.1.3
tnSshPrivKeyPassword Ssh Private key password.	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.7483.2.1.1.2.39.2.1.4

.

tnSysNESshKeyEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.3.1

.

Indexes

tnSysNESshKeyUserName tnSysNESshKeyIndex

Column	Syntax	OID
tnSysNESshKeyUserName .	OctetString Constraints: range: 1-64	.1.3.6.1.4.1.7483.2.1.1.2.39.3.1.1
tnSysNESshKeyIndex .	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.1.1.2.39.3.1.2
tnSysNESshKeyRowStatus The row status.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.39.3.1.3
tnSysNESshKeyString1 The SSH key string 1. Provisions the user public keys used for SSH user authentication. The number of keys configurable per user is defined by available key indices.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.3.1.4
tnSysNESshKeyString2 The SSH key string 2. Provisions the user public keys used for SSH user authentication. The number of keys configurable per user is defined by available key indices.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.3.1.5

.

tnNESshKeyEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.4.1

.

Indexes

tnNESshKeyUserName tnNESshKeyIndex

Column	Syntax	OID
tnNESshKeyUserName .	OctetString Constraints: range: 1-64	.1.3.6.1.4.1.7483.2.1.1.2.39.4.1.1
tnNESshKeyIndex .	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.1.1.2.39.4.1.2
tnNESshKeyRowStatus The row status.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7483.2.1.1.2.39.4.1.3
tnNESshKeyString1 The SSH key string 1. Provisions the user public keys used for SSH user authentication. The number of keys configurable per user is defined by available key indices.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.4.1.4
tnNESshKeyString2 The SSH key string 2. Provisions the user public keys used for SSH user authentication. The number of keys configurable per user is defined by available key indices.	OctetStringr/w Constraints: range: 0-2048	.1.3.6.1.4.1.7483.2.1.1.2.39.4.1.5

.

tnSshCiphersEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.5.1

.

Indexes

tnSshCiphersAlgType tnSshCiphersProfileName

Column	Syntax	OID
tnSshCiphersAlgType This attribute indicates the SSH Ciphers Algorithm type Supported values: aes128-ctr - 1 aes256-ctr - 2 aes128-gcm@openssh.com - 3 aes256-gcm@openssh.com - 4.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.39.5.1.1
tnSshCiphersProfileName This attribute indicates the SSH Ciphers ProfileName.	OctetString	.1.3.6.1.4.1.7483.2.1.1.2.39.5.1.2
tnSshCiphersEnabled This attribute indicates whether the SSH Ciphers algorithm setting is enabled/disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.39.5.1.3

.

tnSshHostKeyEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.6.1

.

Indexes

tnSshHostKeyAlgType tnSshHostKeyProfileName

Column	Syntax	OID
tnSshHostKeyAlgType This attribute indicates the SSH HostKey Algorithm type Supported values: ssh-rsa - 1 rsa-sha2-256 - 2 rsa-sha2-512 - 3 ecdsa-sha2-nistp256 - 4 ecdsa-sha2-nistp384 - 5 ecdsa-sha2-nistp521 …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.39.6.1.1
tnSshHostKeyProfileName This attribute indicates the SSH HostKey Profilename.	OctetString	.1.3.6.1.4.1.7483.2.1.1.2.39.6.1.2
tnSshHostKeyEnabled This attribute indicates whether the SSH HostKey algorithm setting is enabled/disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.39.6.1.3

.

tnSshMacsEntry row .1.3.6.1.4.1.7483.2.1.1.2.39.7.1

.

Indexes

tnSshMacsAlgType tnSshMacsProfileName

Column	Syntax	OID
tnSshMacsAlgType This attribute indicates the SSH Macs Algorithm type Supported values: hmac-sha1 - 1 hmac-sha2-256 - 2 hmac-sha2-512 - 3.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.1.1.2.39.7.1.1
tnSshMacsProfileName This attribute indicates the SSH Macs Profilename.	OctetString	.1.3.6.1.4.1.7483.2.1.1.2.39.7.1.2
tnSshMacsEnabled This attribute indicates whether the SSH Macs algorithm setting is enabled/disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.1.1.2.39.7.1.3