TPLINK-MLDSNOOPING-MIB Table View

MLD Snooping (Internet Group Management Protocol Snooping) 
is a multicast control mechanism running on Layer 2 switch. 
It can effectively prevent multicast groups being broadcasted 
in the network.

tpMldPortEntry row .1.3.6.1.4.1.11863.6.43.1.1.2.1.1

An entry contains of the information of port configure.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
tpMldSnoopingPortEnable Select Enable/Disable MLD Snooping for the desired port. 0. Disable 1. Enable	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.11863.6.43.1.1.2.1.1.2
tpMldFastLeavePortEnable Select Enable/Disable Fast Leave feature for the desired port. If Fast Leave is enabled for a port, the Switch will immediately remove this port from the multicast group upon receiving MLD leave messages. 0. Disable …	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.11863.6.43.1.1.2.1.1.3
tpMldPortLag Displays the LAG number which the port belongs to.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.11863.6.43.1.1.2.1.1.4

Multicast groups established by MLD Snooping are based on VLANs. 
You can configure different MLD parameters for different VLANs.

tpMldVlanEntry row .1.3.6.1.4.1.11863.6.43.1.1.3.1.1

An entry contains of the information of mldsnooping.

Indexes

tpMldVlanId

Column	Syntax	OID
tpMldVlanId Enter the VLAN ID to enable MLD Snooping for the desired VLAN,1-4094.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.1
tpMldVlanEnable Select Enable/Disable MLD Snooping for the desired vlan. 0. Disable 1. Enable	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.2
tpMldVlanFastLeave Select Enable/Disable Fast Leave feature for the desired vlan. If Fast Leave is enabled for a vlan, the Switch will immediately remove this port from the multicast group upon receiving MLD leave messages. 0. Disable …	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.3
tpMldVlanReportSuppression Select Enable/Disable MLD Snooping report suppression function globally on the Switch. 0. Disable 1. Enable	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.4
tpMldRouterTime Specify the aging time of the router port. Within this time, if the switch don't receive MLD query message from the router port, it will consider this port is not a router port any more,0,60-600 second.	Integer32r/w Constraints: range: 60-600	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.5
tpMldMemberTime Specify the aging time of the member port. Within this time, if the switch don't receive MLD report message from the member port, it will consider this port is not a member port any more,0,60-600 second.	Integer32r/w Constraints: range: 60-600	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.6
tpMldLeaveTime Specify the leave time for the VLAN. When the switch receives a leave message from a port to leave a multicast group, it will wait for a leave time before removing the port from the multicast group.	Integer32r/w Constraints: range: 1-30	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.7
tpMldRouterPort Config the static router ports which are mainly used in the network with stable topology.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.8
tpMldForbiddenRouterPort Config the forbidden router ports which are mainly used to forbidden specified ports to become router ports.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.9
tpMldQueryEnable Select Enable/Disable MLD Querier. 0. Disable 1. Enable	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.10
tpMldQueryInterval Enter the Query message interval time. The Querier will send General Query Message with this interval. The interval is ranging from 10 to 300 seconds.	Integer32r/w Constraints: range: 10-300	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.11
tpMldQueryMaxResponseTime Enter the value of Maximum Response Time field of the Query message. The host is expected to response to an IGMP general query within this time. The time is ranging from 1 to 25 seconds.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.12
tpMldQueryGeneralSrcIp Enter the General Query Message source IP address.	OctetStringr/w	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.13
tpMldQueryLastMemberCount Enter the Last Listener Query numbers. When the multicast group has no more member ports, it will send this numbers of Specific Query Message to check whether there is another member. It is ranging from 1 to 5.	Integer32r/w Constraints: range: 1-5	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.14
tpMldQueryLastMemberInterval Enter the Last Listener Query interval time. When the multicast group has no more member ports, it will send the Specific Query Message with this interval time to check whether there is another member. The interval is…	Integer32r/w Constraints: range: 1-5	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.15
tpMldVlanStatus the following two values are states: these values may be read or written active(1), notInService(2), the following value is a state: this value may be read, but not written notReady(3), the…	TPLINK-TC-MIBTPRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.16

When the switch receives MLD report message, it examines 
the multicast filtering IP ID configured on the access port 
to determine if the port can join the multicast group. 
If the multicast IP is not filtered, the switch will add 
the port to the forward port list of the multicast group. 
Otherwise, the switch will drop the MLD report message. 
In that way, you can control the multicast groups that users 
can access.

tpMldFilterPortEntry row .1.3.6.1.4.1.11863.6.43.1.2.1.1.1

An entry contains of the information of a port param.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
tpMldFilterMaxGroup Specify the maximum number of multicast groups to prevent some ports taking up too much bandwidth.	Integer32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.11863.6.43.1.2.1.1.1.2
tpMldFilterMaxGroupAction The policy should be taken when the number of multicast group a port has joined reach the maximum. 0.Drop: drop the successive report packet, and this port can not join any other multicast group. 1.Replace: when the p…	Enumerationr/w Enumerated Values: 0 drop 1 replace	.1.3.6.1.4.1.11863.6.43.1.2.1.1.1.3
tpMldFilterBindAddrId Enter the profile ID the port will be bound to. Only one profile can be bound to each port.	OctetStringr/w Constraints: range: 0-3	.1.3.6.1.4.1.11863.6.43.1.2.1.1.1.4
tpMldFilterPortLag Displays the LAG number which the port belongs to.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.11863.6.43.1.2.1.1.1.5

A list of  multicast statistic Table.

tpMldPktStatEntry row .1.3.6.1.4.1.11863.6.43.1.3.1.1.1

An entry contains of multicast packet statistics over each port.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
tpMldQueryPktStat Displays the number of query packets the port received.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.3.1.1.1.2
tpMldReportV1PktStat Displays the number of MLDv1 report packets the port received.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.3.1.1.1.3
tpMldReportV2PktStat Displays the number of MLDv2 report packets the port received.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.3.1.1.1.4
tpMldDonePktStat Displays the number of done packets the port received.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.3.1.1.1.6
tpMldErrorPktStat Displays the number of error packets the port received.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.3.1.1.1.7

A list of  multicast groups Table.

tpMldMulticastGroupEntry row .1.3.6.1.4.1.11863.6.43.1.4.1.1.1

An entry contains of multicast packet statistics over each port.

Indexes

tpMldMulticastIP tpMldVlanID

Column	Syntax	OID
tpMldMulticastIP Displays the multicast IP address.	OctetString	.1.3.6.1.4.1.11863.6.43.1.4.1.1.1.1
tpMldVlanID Displays the VLAN ID.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.4.1.1.1.2
tpMldForwardPorts Displays the forward ports of multicast group.	OctetString Constraints: range: 0-50	.1.3.6.1.4.1.11863.6.43.1.4.1.1.1.3
tpMldGrouptype Displays the type of multicast group.	Enumeration Enumerated Values: 0 static 1 dynamic	.1.3.6.1.4.1.11863.6.43.1.4.1.1.1.4

A list of  multicast groups Table.

tpMldMulticastStaticGroupEntry row .1.3.6.1.4.1.11863.6.43.1.5.1.1.1

An entry contains of multicast packet statistics over each port.

Indexes

tpMldStaticMulticastIP tpMldStaticVlanID

Column	Syntax	OID
tpMldStaticMulticastIP The multicast IP address.	OctetStringr/w	.1.3.6.1.4.1.11863.6.43.1.5.1.1.1.1
tpMldStaticVlanID The VLAN ID.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11863.6.43.1.5.1.1.1.2
tpMldStaticForwardPorts The forward ports of multicast group.	OctetStringr/w Constraints: range: 0-50	.1.3.6.1.4.1.11863.6.43.1.5.1.1.1.3
tpMldStaticGroupStatus The following values are states: these values may be used as follow: active(1),if the entry is being used. notInService(2),destory the entry. notReady(3),destory the entry. createAndGo(4),not being used c…	TPLINK-TC-MIBTPRowStatusr/w Type Values: 1 active 4 createAndGo 6 destroy	.1.3.6.1.4.1.11863.6.43.1.5.1.1.1.4