TPLINK-IGMPSNOOPING-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
7
Rows
7
Columns
39

tpIgmpPortTable

table
.1.3.6.1.4.1.11863.6.25.1.1.2.1 · 1 row entry · 3 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpPortTable' 
IGMP Snooping (Internet Group Management Protocol Snooping) 
is a multicast control mechanism running on Layer 2 switch. 
It can effectively prevent multicast groups being broadcasted 
in the network.
tpIgmpPortEntry row .1.3.6.1.4.1.11863.6.25.1.1.2.1.1
An entry contains of the information of port configure.
Indexes
Column Syntax OID
tpIgmpSnoopingPortEnable
Select Enable/Disable IGMP Snooping for the desired port.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.1.2.1.1.2
tpIgmpFastLeavePortEnable
Select Enable/Disable Fast Leave feature for the desired port.
If Fast Leave is enabled for a port, the Switch will immediately
remove this port from the multicast group upon receiving IGMP
leave messages.
0. Disable…
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.1.2.1.1.3
tpIgmpPortLag
Displays the LAG number which the port belongs to.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.25.1.1.2.1.1.4

tpIgmpVlanTable

table
.1.3.6.1.4.1.11863.6.25.1.1.3.1 · 1 row entry · 16 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpVlanTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpVlanTable' 
Multicast groups established by IGMP Snooping are based on VLANs. 
You can configure different IGMP parameters for different VLANs.
tpIgmpVlanEntry row .1.3.6.1.4.1.11863.6.25.1.1.3.1.1
An entry contains of the information of igmpsnooping.
Indexes
Column Syntax OID
tpIgmpVlanId
Enter the VLAN ID to enable IGMP Snooping for the desired VLAN,1-4094.
Integer32
Constraints:
range: 1-4094
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.1
tpIgmpVlanEnable
Select Enable/Disable IGMP Snooping for the desired vlan.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.2
tpIgmpVlanFastLeave
Select Enable/Disable Fast Leave feature for the desired vlan.
If Fast Leave is enabled for a vlan, the Switch will immediately
remove this port from the multicast group upon receiving IGMP
leave messages.
0. Disable…
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.3
tpIgmpVlanReportSuppression
Select Enable/Disable IGMP Snooping report suppression function globally on the Switch.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.4
tpIgmpRouterTime
Specify the aging time of the router port. Within this time,
if the switch don't receive IGMP query message from the router port,
it will consider this port is not a router port any more,0,60-600 second.
Integer32r/w
Constraints:
range: 60-600
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.5
tpIgmpMemberTime
Specify the aging time of the member port. Within this time,
if the switch don't receive IGMP report message from the member port,
it will consider this port is not a member port any more,0,60-600 second.
Integer32r/w
Constraints:
range: 60-600
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.6
tpIgmpLeaveTime
Specify the leave time for the VLAN.
When the switch receives a leave message from a port to leave a multicast group,
it will wait for a leave time before removing the port from the multicast group.
Integer32r/w
Constraints:
range: 1-30
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.7
tpIgmpRouterPort
Config the static router ports which are mainly used in the network with
stable topology.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.8
tpIgmpForbiddenRouterPort
Config the forbidden router ports which are mainly used to forbidden
specified ports to become router ports.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.9
tpIgmpQueryEnable
Select Enable/Disable IGMP Querier.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.10
tpIgmpQueryInterval
Enter the Query message interval time. The Querier will send General Query Message with this interval. The interval is ranging from 10 to 300 seconds.
Integer32r/w
Constraints:
range: 10-300
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.11
tpIgmpQueryMaxResponseTime
Enter the value of Maximum Response Time field of the Query message. The host is expected to response to an IGMP general query within this time. The time is ranging from 1 to 25 seconds.
Integer32r/w
Constraints:
range: 1-25
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.12
tpIgmpQueryGeneralSrcIp
Enter the General Query Message source IP address.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.13
tpIgmpQueryLastMemberCount
Enter the Last Listener Query numbers. When the multicast group has no more member ports,
it will send this numbers of Specific Query Message to check whether there is another member.
It is ranging from 1 to 5.
Integer32r/w
Constraints:
range: 1-5
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.14
tpIgmpQueryLastMemberInterval
Enter the Last Listener Query interval time. When the multicast group has no more member ports,
it will send the Specific Query Message with this interval time to check whether there is another
member. The interval is…
Integer32r/w
Constraints:
range: 1-5
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.15
tpIgmpVlanStatus
the following two values are states:
these values may be read or written
active(1),
notInService(2),

the following value is a state:
this value may be read, but not written
notReady(3),

the…
TPLINK-TC-MIBTPRowStatusr/w
Type Values:
1active
4createAndGo
6destroy
 .1.3.6.1.4.1.11863.6.25.1.1.3.1.1.16

tpIgmpFilterPortTable

table
.1.3.6.1.4.1.11863.6.25.1.2.1.1 · 1 row entry · 4 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpFilterPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpFilterPortTable' 
When the switch receives IGMP report message, it examines 
the multicast filtering IP ID configured on the access port 
to determine if the port can join the multicast group. 
If the multicast IP is not filtered, the switch will add 
the port to the forward port list of the multicast group. 
Otherwise, the switch will drop the IGMP report message. 
In that way, you can control the multicast groups that users 
can access.
tpIgmpFilterPortEntry row .1.3.6.1.4.1.11863.6.25.1.2.1.1.1
An entry contains of the information of a port param.
Indexes
Column Syntax OID
tpIgmpFilterMaxGroup
Specify the maximum number of multicast groups to prevent some
ports taking up too much bandwidth.
Integer32r/w
Constraints:
range: 0-1000
 .1.3.6.1.4.1.11863.6.25.1.2.1.1.1.2
tpIgmpFilterMaxGroupAction
The policy should be taken when the number of multicast group
a port has joined reach the maximum.
0.Drop: drop the successive report packet, and this port can
not join any other multicast group.
1.Replace: when the p…
Enumerationr/w
Enumerated Values:
0drop
1replace
 .1.3.6.1.4.1.11863.6.25.1.2.1.1.1.3
tpIgmpFilterBindAddrId
Enter the profile ID the port will be bound to. Only one profile
can be bound to each port.
OctetStringr/w
Constraints:
range: 0-3
 .1.3.6.1.4.1.11863.6.25.1.2.1.1.1.4
tpIgmpFilterPortLag
Displays the LAG number which the port belongs to.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.25.1.2.1.1.1.5

tpIgmpAuthPortTable

table
.1.3.6.1.4.1.11863.6.25.1.3.1.1 · 1 row entry · 2 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpAuthPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpAuthPortTable' 
IGMP Authentication can control the access of multicast packets.
tpIgmpAuthPortEntry row .1.3.6.1.4.1.11863.6.25.1.3.1.1.1
An entry contains of the information of port authentication configure.
Indexes
Column Syntax OID
tpIgmpAuthEnable
Select Enable/Disable IGMP Authentication for the desired port.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.25.1.3.1.1.1.2
tpIgmpAuthPortLag
Displays the LAG number which the port belongs to.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.25.1.3.1.1.1.3

tpIgmpPktStatTable

table
.1.3.6.1.4.1.11863.6.25.1.4.1.1 · 1 row entry · 6 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpPktStatTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpPktStatTable' 
A list of  multicast statistic Table.
tpIgmpPktStatEntry row .1.3.6.1.4.1.11863.6.25.1.4.1.1.1
An entry contains of multicast packet statistics over each port.
Indexes
Column Syntax OID
tpIgmpQueryPktStat
Displays the number of query packets the port received.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.4.1.1.1.2
tpIgmpReportV1PktStat
Displays the number of IGMPv1 report packets the port received.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.4.1.1.1.3
tpIgmpReportV2PktStat
Displays the number of IGMPv2 report packets the port received.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.4.1.1.1.4
tpIgmpReportV3PktStat
Displays the number of IGMPv3 report packets the port received.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.4.1.1.1.5
tpIgmpLeavePktStat
Displays the number of leave packets the port received.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.4.1.1.1.6
tpIgmpErrorPktStat
Displays the number of error packets the port received.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.4.1.1.1.7

tpIgmpMulticastGroupTable

table
.1.3.6.1.4.1.11863.6.25.1.5.1.1 · 1 row entry · 4 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpMulticastGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpMulticastGroupTable' 
A list of  multicast groups Table.
tpIgmpMulticastGroupEntry row .1.3.6.1.4.1.11863.6.25.1.5.1.1.1
An entry contains of multicast packet statistics over each port.
Indexes
Column Syntax OID
tpIgmpMulticastIP
Displays the multicast IP address.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
 .1.3.6.1.4.1.11863.6.25.1.5.1.1.1.1
tpIgmpVlanID
Displays the VLAN ID.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.5.1.1.1.2
tpIgmpForwardPorts
Displays the forward ports of multicast group.
OctetString
Constraints:
range: 0-50
 .1.3.6.1.4.1.11863.6.25.1.5.1.1.1.3
tpIgmpGrouptype
Displays the type of multicast group.
Enumeration
Enumerated Values:
0static
1dynamic
 .1.3.6.1.4.1.11863.6.25.1.5.1.1.1.4

tpIgmpMulticastStaticGroupTable

table
.1.3.6.1.4.1.11863.6.25.1.6.1.1 · 1 row entry · 4 columns
Open in standard view
Uses the tplink variant from /opt/observium/mibs/tplink.
Command help
Walk tpIgmpMulticastStaticGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TPLINK-IGMPSNOOPING-MIB' -M '/opt/observium/mibs/tplink:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TPLINK-IGMPSNOOPING-MIB::tpIgmpMulticastStaticGroupTable' 
A list of  multicast groups Table.
tpIgmpMulticastStaticGroupEntry row .1.3.6.1.4.1.11863.6.25.1.6.1.1.1
An entry contains of multicast packet statistics over each port.
Indexes
Column Syntax OID
tpIgmpStaticMulticastIP
The multicast IP address.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
 .1.3.6.1.4.1.11863.6.25.1.6.1.1.1.1
tpIgmpStaticVlanID
The VLAN ID.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.25.1.6.1.1.1.2
tpIgmpStaticForwardPorts
The forward ports of multicast group.
OctetStringr/w
Constraints:
range: 0-50
 .1.3.6.1.4.1.11863.6.25.1.6.1.1.1.3
tpIgmpStaticGroupStatus
The following values are states:
these values may be used as follow:

active(1),if the entry is being used.
notInService(2),destory the entry.
notReady(3),destory the entry.
createAndGo(4),not being used
c…
TPLINK-TC-MIBTPRowStatusr/w
Type Values:
1active
4createAndGo
6destroy
 .1.3.6.1.4.1.11863.6.25.1.6.1.1.1.4