TN-IEEE8021-CFM-MIB Table View

There is one CFM Stack table per bridge. It permits
the retrieval of information about the Maintenance Points
configured on any given interface.

tnDot1agCfmStackEntry row .1.3.6.1.4.1.7483.6.1.2.52.1.2.1

The Stack table entry

Indexes

tnDot1agCfmStackifIndex tnDot1agCfmStackVlanIdOrNone tnDot1agCfmStackMdLevel tnDot1agCfmStackDirection

Column	Syntax	OID
tnDot1agCfmStackifIndex This object represents the Bridge Port or aggregated port on which MEPs or MHFs might be configured. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable, and …	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.1
tnDot1agCfmStackVlanIdOrNone VLAN ID to which the MP is attached, or 0, if none.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.2
tnDot1agCfmStackMdLevel MD Level of the Maintenance Point.	IEEE8021-CFM-MIBDot1agCfmMDLevel Type Constraints: range: 0..7	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.3
tnDot1agCfmStackDirection Direction in which the MP faces on the Bridge Port	IEEE8021-CFM-MIBDot1agCfmMpDirection Type Values: 1 down 2 up	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.4
tnDot1agCfmStackMdIndex The index of the Maintenance Domain in the dot1agCfmMdTable to which the MP is associated, or 0, if none.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.5
tnDot1agCfmStackMaIndex The index of the MA in the dot1agCfmMaNetTable and dot1agCfmMaCompTable to which the MP is associated, or 0, if none.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.6
tnDot1agCfmStackMepId If an MEP is configured, the MEPID, else 0	IEEE8021-CFM-MIBDot1agCfmMepIdOrZero Type Constraints: range: 0..8191	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.7
tnDot1agCfmStackMacAddress MAC address of the MP.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.8
tnDot1agCfmStackMPType The value of tnDot1agCfmStackMPType indicates the entity that the MP is configured on: sap(1) MP is configured on a SAP ethTun(2) MP is configured on an ethernet-tunnel	Enumeration Enumerated Values: 1 sap 2 ethTun 3 ethRing 4 facPort 5 facInterface	.1.3.6.1.4.1.7483.6.1.2.52.1.2.1.9

A row in the tnDot1agCfmMcLagConfigTable indicates whether a Mc Lag
is in Active Standby or not and what the Hold Time will be.

tnDot1agCfmMcLagConfigEntry row .1.3.6.1.4.1.7483.6.1.2.52.2.1.1

The Cfm entry for MC LAG

Indexes

TROPIC-SYSTEM-MIBtnSysSwitchId

Column	Syntax	OID
tnDot1agCfmMcLagConfigStdbyInactive The value of tnDot1agCfmMcLagConfigStdbyInactive specifies whether or not ETH-CFM MEPs configured on Multi-Chassis LAG ports are aware of MC-LAG port active/standby states. When this object is 'true (1)',…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.6.1.2.52.2.1.1.1
tnDot1agCfmMcLagConfigPropHoldTime The value of tnDot1agCfmMcLagConfigPropHoldTime specifies the duration, in seconds, of a timer that is activated when an MC-LAG port or protocol changes state. While the timer is active, no fault set or clear is propaga…	secondsUnsigned32r/w Constraints: range: 0-60	.1.3.6.1.4.1.7483.6.1.2.52.2.1.1.2

The tnDot1agCfmComponentLimitTable stores the current resource counts
as well as their resource limits for Ethernet Connectivity Fault
Management (ETH-CFM) components in the SROS series system.

tnDot1agCfmComponentLimitEntry row .1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1

The tnDot1agCfmComponentLimitEntry consists of the resource limits
for a particular component of ETH-CFM.

Rows are managed by the system and can not be created or destroyed using
SNMP set requests.

Indexes

TROPIC-SYSTEM-MIBtnSysSwitchId tnDot1agCfmCompMajorIndex tnDot1agCfmCompMinorIndex

Column	Syntax	OID
tnDot1agCfmCompMajorIndex The value of tnDot1agCfmCompMajorIndex specifies the major identifier of the ETH-CFM component.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.1
tnDot1agCfmCompMinorIndex The value of tnDot1agCfmCompMinorIndex specifies the minor identifier of the ETH-CFM component.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.2
tnDot1agCfmCompName The value of tnDot1agCfmCompName indicates the name of the ETH-CFM component.	TN-TC-MIBTNamedItem Type Constraints: range: 1..32	.1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.3
tnDot1agCfmCompResourceUsage The value of tnDot1agCfmCompResourceUsage indicates the current resource usage for the ETH-CFM component.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.4
tnDot1agCfmCompResourceLimit The value of tnDot1agCfmCompResourceLimit indicates the maximum resource usage limit for the ETH-CFM component for the SROS series system.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.5

The tnDot1agCfmMaNetTable AUGMENTS the standard MIB table,
dot1agCfmMaNetTable. This table is used to enhance Maintenance
Association functionality for Ethernet Connectivity Fault Management
(ETH-CFM).

tnDot1agCfmMaNetEntry row .1.3.6.1.4.1.7483.6.1.2.52.6.1.1

The tnDot1agCfmMaNetEntry consists of the configuration objects
used to enhance the Maintenance Association functionality.

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMaNetTotalMEPCount The value of tnDot1agCfmMaNetTotalMEPCount indicates the number of unique MEPs configured (both local and remote) that are associated with this MA. When the number of MEPs exceed the normal MA limits, the…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.6.1.1.1

The tnDot1agCfmMaMepListTable extends the functionality of the
dot1agCfmMaMepListTable.

tnDot1agCfmMaMepListEntry row .1.3.6.1.4.1.7483.6.1.2.52.6.3.1

The tnDot1agCfmMaMepListEntry augments the standard MIB entry
for the purpose of extending functionality for Dot1ag CFM MEP Lists.
Rows are created and destroyed by the system through the row status
field in dot1agCfmMa…

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMaMepListMacAddress The value of tnDot1agCfmMaMepListMacAddress specifies the target unicast MAC address used for transmitting CFM packets to the remote MEPs for the specified MEPID. Setting a unicast MAC address restricts t…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.6.3.1.1
tnDot1agCfmMaMepListSapSubType The value of tnDot1agCfmMaMepListSapSubType specifies the SAP sub type of the remote MEP for the specified MEPID. This is used to ensure that LLF shutdown is based only on remote etree-root SAP faults and…	Enumerationr/w Enumerated Values: 0 regular 1 etree-root 2 etree-leaf	.1.3.6.1.4.1.7483.6.1.2.52.6.3.1.2

This table augments the Maintenance Association End Point (MEP) table
of the IEEE8021-CFM-MIB.

tnDot1agCfmMepEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.1.1

A conceptual row in the tnDot1agCfmMepTable. This row exists only
if the association dot1agCfmMepEntry is active.

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMepSdpId The value of tnDot1agCfmMepSdpId specifies, along with the tnDot1agCfmMepVcId, the SDP-Binding within a bridge port, to which the MEP is attached. This object is applicable to SDP-Bindings only, and MUST …	TN-SERV-MIBSdpIdr/w Type Constraints: range: 0..17407	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.1
tnDot1agCfmMepVcId The value of tnDot1agCfmMepVcId specifies, along with tnDot1agCfmMepSdpId, the SDP Binding for the bridge. tnDot1agCfmMepVcId is applicable to SDP-Bindings only, and MUST be set to zero (0) when dot1agCfm…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.2
tnDot1agCfmMepMacAddress The value of tnDot1agCfmMepMacAddress specifies the mac-address that is assigned to dot1agCfmMepMacAddress.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.3
tnDot1agCfmMepAisEnable The value of tnDot1agCfmMepAisEnable specifies whether AIS frames are generated from the Maintenance Entity Group (MEG).	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.4
tnDot1agCfmMepAisMegLevel The value of tnDot1agCfmMepAisMegLevel specifies the levels that should be notified to suppress alarms resulting from defect conditions detected by the MEP.	Bitsr/w Enumerated Values: 0 level1 1 level2 2 level3 3 level4 4 level5 5 level6 6 level7	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.5
tnDot1agCfmMepAisPriority The value of tnDot1agCfmMepAisPriority specifies at what priority the AIS frames should be transmitted.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.6
tnDot1agCfmMepAisInterval The value of tnDot1agCfmMepAisInterval specifies at what intervals to transmit AIS frames.	secondsUnsigned32r/w Constraints: range: 60-60 range: 1-1	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.7
tnDot1agCfmMepEthRxAisInterval The value of tnDot1agCfmMepEthRxAisInterval indicates the AIS Interval received in the last AIS Frame.	secondsUnsigned32 Constraints: range: 60-60 range: 1-1	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.8
tnDot1agCfmMepEthRxAis The value of tnDot1agCfmMepEthRxAis indicates the MEP is receiving AIS test frames from one or more of its sub-layer MEPs.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.9
tnDot1agCfmMepEthAisTxCount The value of tnDot1agCfmMepEthAisTxCount indicates number of AIS frames transmitted on the MEP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.10
tnDot1agCfmMepEthTestEnable The value of tnDot1agCfmMepEthTestEnable specifies whether ethernet test frames are to be generated on transmission or processed on reception. If this object is set to 'false', then tnDot1agCfmMepEthTestPattern is undef…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.11
tnDot1agCfmMepEthTestPattern The value of tnDot1agCfmMepEthTestPattern specifies the data-content of the AIS test frames. 'allZerosNoCrc (0)' and 'allZerosCrc (1)' specifies the data content as all zero values (without and with CRC calculations res…	Enumerationr/w Enumerated Values: 0 allZerosNoCrc 1 allZerosCrc 2 prbsNoCrc 3 prbsCrc 4 allOnesNoCrc 5 allOnesCrc	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.12
tnDot1agCfmMepEthTestMacAddr The value of tnDot1agCfmMepEthTestMacAddr specifies the MAC address of the target to whom the Eth-test frames are sent. Setting this object will trigger the test frame to be sent. Once the test is complet…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.13
tnDot1agCfmMepEthTestDataLen The value of tnDot1agCfmMepEthTestDataLen specifies the length of the data sent in an Eth-test frame. The contents of the data is specified by the tnDot1agCfmMepEthTestPattern object.	Unsigned32r/w Constraints: range: 64-1500	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.14
tnDot1agCfmMepEthTestPriority The value of tnDot1agCfmMepEthTestPriority specifies the priority used in generating Eth-Test frames.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.15
tnDot1agCfmMepOWDTMacAddress The value of tnDot1agCfmMepOWDTMacAddress specifies the MAC address used as a target for the One-Way-Delay Test (OWDT). Setting this object will trigger a One-Way-Delay test to the specified MAC address. …	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.16
tnDot1agCfmMepOWDTPriority The value of tnDot1agCfmMepOWDTPriority specifies the priority used in the generated test frame for the One-Way-Delay test.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.17
tnDot1agCfmMepTWDTMacAddress The value of tnDot1agCfmMepTWDTMacAddress specifies the MAC address used as a target for the Two-Way-Delay Test (TWDT). Setting this object will trigger a Two-Way-Delay test to the specified MAC address. …	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.18
tnDot1agCfmMepTWDTPriority The value of tnDot1agCfmMepTWDTPriority specifies the priority used in the generated test frame for the Two-Way-Delay test.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.19
tnDot1agCfmMepSvcId The value of tnDot1agCfmMepSvcId specifies the service that the virtual MEP is being created in. tnDot1agCfmMepSvcId is applicable to virtual MEPs only, and MUST be set to zero (0) when dot1agCfmMepIfInde…	TN-TC-MIBTmnxServIdr/w Type Constraints: range: 0..2147483650	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.20
tnDot1agCfmMepControlMep The value of tnDot1agCfmMepControlMep specifies whether or not the operational state of the MEP is used by the management entity over which this MEP is configured.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.21
tnDot1agCfmMepEthTestThreshold The value of tnDot1agCfmMepEthTestThreshold specifies when a tnDot1agCfmMepEthTestComplete notification is sent. If tnDot1agCfmMepEthTestThreshold is set to zero (0), a notification is sent on the completion of any test…	bit-errorsUnsigned32r/w Constraints: range: 0-11840	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.22
tnDot1agCfmMepOWDTThreshold The value of tnDot1agCfmMepOWDTThreshold specifies when a tnDot1agCfmMepDMTestComplete notification is sent for a one-way-delay test. If tnDot1agCfmMepOWDTThreshold is set to zero (0), a notification is sent on the comp…	secondsUnsigned32r/w Constraints: range: 0-600	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.23
tnDot1agCfmMepMcLagInactive The value of tmnxDot1agCfmMepMcLagInactive indicates whether or not the MEP is inactive, 'standby (2)', due to the MC-LAG standby state. The value of tmnxDot1agCfmMcLagStdbyInactive must be set to 'true (1)' for this o…	Enumeration Enumerated Values: 0 notApplicable 1 standby 2 active	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.24
tnDot1agCfmMepTWDTDataSize The value of tnDot1agCfmMepTWDTDataSize specifies the data size, in bytes, contained in the padding TLV for the Two-Way delay test. A value of zero (0) specifies that no padding TLV is inserted in the packet. Any non-ze…	bytesUnsigned32r/w Constraints: range: 0-9542	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.25
tnDot1agCfmMepTransmitLbmDataTlvSize The value of tnDot1agCfmMepTransmitLbmDataTlvSize specifies the data size, in bytes, contained in the padding TLV for the LBM test. A value of zero (0) specifies that no padding TLV is inserted in the packet. Any non-…	bytesUnsigned32r/w Constraints: range: 0-9570	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.26
tnDot1agCfmMepType The value of tmnxDot1agCfmMepType specifies the endpoint type that this MEP facilitates. default (0) -- implements a traditional MEP. facilityPort (1) -- implements a facility port/LAG level MEP. …	Enumerationr/w Enumerated Values: 0 default 1 facilityPort 2 facilityInterface 3 sapPrimaryVlan	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.27
tnDot1agCfmMepFaultPropagation The value of tnDot1agCfmMepFaultPropagation specifies what action should be taken by the MEP if a fault is detected in the service containing the MEP. It also specifies if the MEP should propagate a fault that it has d…	Enumerationr/w Enumerated Values: 0 disabled 1 useIfStatusTLV 2 suspendCCM	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.28
tnDot1agCfmMepOWDTDataSize The value of tnDot1agCfmMepOWDTDataSize specifies the data size, in bytes, contained in the padding TLV for the one-Way delay test. A value of zero (0) specifies that no padding TLV is inserted in the packet. Any non-ze…	bytesUnsigned32r/w Constraints: range: 0-9542	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.29
tnDot1agCfmMepAlmProfName .	OctetStringr/w Constraints: range: 1-40	.1.3.6.1.4.1.7483.6.1.2.52.7.1.1.30

The tnDot1agCfmMepDelayRsltTable indicates the results of
all the One-Way/Two-Way Delay Tests from the originating MAC
addresses.
          
This table is not persistent over reboots of the chassis.

tnDot1agCfmMepDelayRsltEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.3.1

The MEG result table.

Indexes

IEEE8021-CFM-MIBdot1agCfmMdIndex IEEE8021-CFM-MIBdot1agCfmMaIndex IEEE8021-CFM-MIBdot1agCfmMepIdentifier tnDot1agCfmMepDelaySrcMacAddr tnDot1agCfmMepDelayTestType

Column	Syntax	OID
tnDot1agCfmMepDelaySrcMacAddr The value of tnDot1agCfmMepDelaySrcMacAddr indicates the source MAC address of the issuer of the test.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.1
tnDot1agCfmMepDelayTestType The value of tnDot1agCfmMepDelayTestType indicates the type of test this row details.	Enumeration Enumerated Values: 1 oneWayTest 2 twoWayTest	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.2
tnDot1agCfmMepDelayTestDelay The value of tnDot1agCfmMepDelayTestDelay indicates the amount of time, measured in microseconds, from when the test-frame was transmitted to the time it was received minus the local processing time taken by the remote …	microsecondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.3
tnDot1agCfmMepDelayVariation The value of tnDot1agCfmMepDelayVariation indicates the amount of time delay variation, measured in microseconds, from the two most recent time delay measurements. Bi-direction test delay variation for tw…	microsecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.4
tnDot1agCfmMepDelayNearEndTestDelay Near end test delay for oneWayTest.	microsecondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.5
tnDot1agCfmMepDelayNearEndVariation Near end test delay variation for oneWayTest.	microsecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.6
tnDot1agCfmMepDelayFarEndTestDelay Far end test delay for oneWayTest	microsecondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.7
tnDot1agCfmMepDelayFarEndVariation Far end test delay variation for oneWayTest.	microsecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.3.1.8

This table augments the Maintenance Association End Point (MEP) table
of the IEEE8021-CFM-MIB.

tnDot1agCfmMepCsfEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.4.1

A conceptual row in the tnDot1agCfmMepCsfTable. This row exists only
if the association dot1agCfmMepEntry is active.

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMepCsfInterval Interval between CSF transmissions to be used in the MEP.	IEEE8021-CFM-MIBDot1agCfmCcmIntervalr/w Type Values: 0 intervalInvalid 1 interval300Hz 2 interval10ms 3 interval100ms 4 interval1s 5 interval10s 6 interval1min 7 interval10min	.1.3.6.1.4.1.7483.6.1.2.52.7.4.1.1
tnDot1agCfmMepCsfDirection CSF transmissions direction in the MEP	Enumerationr/w Enumerated Values: 1 disable 2 unidirection 3 bi-dirction	.1.3.6.1.4.1.7483.6.1.2.52.7.4.1.2
tnDot1agCfmMepCsfPriority The priority value for CSFs transmitted by the MEP. Default Value is the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default value for t…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.4.1.3

tnDot1agCfmMepSlmTWTestTable consists of the MEP configuration for
issuing individual Synthetic Loss Measurement tests.

tnDot1agCfmMepSlmTWTestEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.5.1

tnDot1agCfmMepSlmTWTestEntry contains the configuration for
generating Synthetic Loss Measurement (SLM) Tests for a particular MEP.
A row exists for each row in the dot1agCfmMepTable, and is destroyed
automatically with…

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMepSlmTWTestStatus The value of tnDot1agCfmMepSlmTWTestStatus specifies the operational state of the two-way Synthetic Loss Measurement (SLM) test. To issue a two-way SLM test the user must issue an SNMP SET on this object …	TN-TC-MIBTmnxEnabledDisabledr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.1
tnDot1agCfmMepSlmTWTestId The value of tnDot1agCfmMepSlmTWTestId indicates the test identifier used to initiate the two-way Synthetic Loss Measurement (SLM) test.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.2
tnDot1agCfmMepSlmTWMacAddress The value of tnDot1agCfmMepSlmTWMacAddress specifies the MAC address used as a target for the two-way Synthetic Loss Measurement (SLM) test. This object MUST be set to a valid MAC Address for proper execu…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.3
tnDot1agCfmMepSlmTWPriority The value of tnDot1agCfmMepSlmTWPriority specifies the priority used in the generated test frame for the two-way Synthetic Loss Measurement (SLM) test.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.4
tnDot1agCfmMepSlmTWInterval The value of tnDot1agCfmMepSlmTWInterval specifies the delay, in seconds, between Synthetic Loss Measurement (SLM) messages for the two-way SLM test. Following are the allowed value for 1830 TPS: {33,…	secondsUnsigned32r/w Constraints: range: 1-5000	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.5
tnDot1agCfmMepSlmTWTimeout The value of tnDot1agCfmMepSlmTWTimeout specifies the time-out value, in seconds, to wait for a Synthetic Loss Measurement (SLM) message to reply for the two-way SLM test. Upon expiration of the timeout period, the agen…	secondsUnsigned32r/w Constraints: range: 1-10	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.6
tnDot1agCfmMepSlmTWDataSize The value of tnDot1agCfmMepSlmTWDataSize specifies the data size, in bytes, contained in the padding TLV for the two-way Synthetic Loss Measurement (SLM) test. A value of zero (0) specifies that no padding TLV is insert…	bytesUnsigned32r/w Constraints: range: 0-9558	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.7
tnDot1agCfmMepSlmTWSendCount The value of tnDot1agCfmMepSlmTWSendCount specifies the number of Synthetic Loss Measurement (SLM) packets to send during the two-way SLM test.	packetsUnsigned32r/w Constraints: range: 1-1000	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.8
tnDot1agCfmMepSlmTWIntervalRedef The value of tnDot1agCfmMepSlmTWIntervalRedef specifies the interval of SLM frames transmitted. The permitted values are 100ms(0),1s (1),10s(2),1m(3),10(4).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.9
tnDot1agCfmMepSlmTWIntrvlUnits The value of tnDot1agCfmMepSlmTWIntrvlUnits, in conjuction with tnDot1agCfmMepSlmTWInterval, specifies the interval between Synthetic Loss Measurement (SLM) messages sent by the two-way SLM test. For example, if tnDot1…	Enumerationr/w Enumerated Values: 1 seconds 2 centiseconds 3 decimilliseconds	.1.3.6.1.4.1.7483.6.1.2.52.7.5.1.10

tnDot1agCfmMepSlmOWTestTable consists of the MEP configuration for
issuing individual Synthetic Loss Measurement one-way tests.

tnDot1agCfmMepSlmOWTestEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.6.1

tnDot1agCfmMepSlmOWTestEntry contains the configuration for
generating Synthetic Loss Measurement (SLM) Tests for a particular MEP.
A row exists for each row in the dot1agCfmMepTable, and is destroyed
automatically with…

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMepSlmOWTestStatus The value of tnDot1agCfmMepSlmOWTestStatus specifies the operational state of the one-way Synthetic Loss Measurement (SLM) test. To issue a one-way SLM test the user must issue an SNMP SET on this object …	TN-TC-MIBTmnxEnabledDisabledr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.1
tnDot1agCfmMepSlmOWTestId The value of tnDot1agCfmMepSlmOWTestId indicates the test identifier used to initiate the one-way Synthetic Loss Measurement (SLM) test.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.2
tnDot1agCfmMepSlmOWMacAddress The value of tnDot1agCfmMepSlmOWMacAddress specifies the MAC address used as a target for the one-way Synthetic Loss Measurement (SLM) Test. This object MUST be set to a valid MAC Address for proper execu…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.3
tnDot1agCfmMepSlmOWPriority The value of tnDot1agCfmMepSlmOWPriority specifies the priority used in the generated test frame for the one-way Synthetic Loss Measurement (SLM) test.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.4
tnDot1agCfmMepSlmOWInterval The value of tnDot1agCfmMepSlmOWInterval specifies the delay, in seconds, between Synthetic Loss Measurement (SLM) messages for the one-way SLM test.	secondsUnsigned32r/w Constraints: range: 1-10	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.5
tnDot1agCfmMepSlmOWDataSize The value of tnDot1agCfmMepSlmOWDataSize specifies the data size, in bytes, contained in the padding TLV for the one-way Synthetic Loss Measurement (SLM) test. A value of zero (0) specifies that no padding TLV is insert…	bytesUnsigned32r/w Constraints: range: 0-1500	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.6
tnDot1agCfmMepSlmOWSendCount The value of tnDot1agCfmMepSlmOWSendCount specifies the number of Synthetic Loss Measurement (SLM) packets to send consecutively during the one-way SLM test.	packetsUnsigned32r/w Constraints: range: 1-100	.1.3.6.1.4.1.7483.6.1.2.52.7.6.1.7

tnDot1agCfmMepSlmTestRsltTable consists of the results of manually
triggered Synthetic Loss Measurement tests.

tnDot1agCfmMepSlmTestRsltEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.7.1

tnDot1agCfmMepSlmTestRsltEntry contains the results of a
manually triggered Synthetic Loss Measurement (SLM) test for a
particular MEP. Rows are auto-generated by the system based on the
issuing of a SLM test.

Indexes

IEEE8021-CFM-MIBdot1agCfmMdIndex IEEE8021-CFM-MIBdot1agCfmMaIndex IEEE8021-CFM-MIBdot1agCfmMepIdentifier tnDot1agCfmMepSlmTestType tnDot1agCfmMepSlmRemoteMacAddr

Column	Syntax	OID
tnDot1agCfmMepSlmTestType The value of tnDot1agCfmMepSlmTestType specifies whether the row for this Synthetic Loss Measurement (SLM) test refers to a two-way SLM test.	Enumeration Enumerated Values: 1 oneWayTest 2 twoWayTest	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.1
tnDot1agCfmMepSlmRemoteMacAddr The value of tnDot1agCfmMepSlmRemoteMacAddr specifies the source MAC address of the remote node involved in the test.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.2
tnDot1agCfmMepSlmTestId The value of tnDot1agCfmMepSlmTestId indicates the test identifier that was used to initiate the Synthetic Loss Measurement (SLM) test.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.3
tnDot1agCfmMepSlmRemoteMepId The value of tnDot1agCfmMepSlmRemoteMepId indicates the MEP Identifier of the remote node involved in the test.	IEEE8021-CFM-MIBDot1agCfmMepId Type Constraints: range: 1..8191	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.4
tnDot1agCfmMepSlmLastTxSeqF The value of tnDot1agCfmMepSlmLastTxSeqF indicates the last received sequence number on the local node, transmitted by the remote node.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.5
tnDot1agCfmMepSlmPacketIn The value of tnDot1agCfmMepSlmPacketIn indicates the number of packets received during the execution of the test.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.6
tnDot1agCfmMepSlmPacketLossIn The value of tnDot1agCfmMepSlmPacketLossIn indicates the number of packets transmitted from the remote node but not received on the local node during the execution of the test.	packetsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.7
tnDot1agCfmMepSlmPacketLossOut The value of tnDot1agCfmMepSlmPacketLossOut indicates the number of packets transmitted from the local node but not received on the remote node during the execution of the test.	packetsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.8
tnDot1agCfmMepSlmPacketUnack The value of tnDot1agCfmMepSlmPacketUnack indicates the number of unacknowledged lost packets during the execution of the test.	packetsSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.7.1.9

tnDot1agCfmMepOndemandLmTestTable consists of the MEP configuration for
issuing individual on-demand Regular Loss Measurement tests.

tnDot1agCfmMepOndemandLmTestEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.8.1

tnDot1agCfmMepOndemandLmTestEntry contains the configuration for
generating regular Loss Measurement (LM) Tests for a particular MEP.
A row exists for each row in the dot1agCfmMepTable, and is destroyed
automatically wi…

Indexes

No indexes recorded

Column	Syntax	OID
tnDot1agCfmMepOndemandLmTestStatus The value of tnDot1agCfmMepOndemandLmTestStatus specifies the operational state of the on-demand regular Loss Measurement (LM) test. To issue a on-demand regular LM test the user must issue an SNMP SET on…	TN-TC-MIBTmnxEnabledDisabledr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.7483.6.1.2.52.7.8.1.1
tnDot1agCfmMepOndemandLmDestMacAddress The value of tnDot1agCfmMepOndemandLmMacAddress specifies the MAC address used as a target for the on-demand regular Loss Measurement (LM) test. This object MUST be set to a valid MAC Address for proper e…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.8.1.2
tnDot1agCfmMepOndemandLmPriority The value of tnDot1agCfmMepOndemandLmPriority specifies the priority used in the generated test frame for the on-demand regular Loss Measurement (LM) test.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7483.6.1.2.52.7.8.1.3
tnDot1agCfmMepOndemandLmInterval The value of tnDot1agCfmMepOndemandLmInterval specifies the delay, in seconds, between on-demand regular Loss Measurement (LM) messages for the on-demand regular LM test. allowed values: 100ms, 1s(default), 10s, 1m, 10m.	IEEE8021-CFM-MIBDot1agCfmCcmIntervalr/w Type Values: 0 intervalInvalid 1 interval300Hz 2 interval10ms 3 interval100ms 4 interval1s 5 interval10s 6 interval1min 7 interval10min	.1.3.6.1.4.1.7483.6.1.2.52.7.8.1.4
tnDot1agCfmMepOndemandLmSendCount The value of tnDot1agCfmMepOndemandLmSendCount specifies the number of LMM packets to send during the on-demand regular LM test.	packetsUnsigned32r/w Constraints: range: 2-101	.1.3.6.1.4.1.7483.6.1.2.52.7.8.1.5
tnDot1agCfmMepOndemandLmTimeout The value of tnDot1agCfmMepOndemandLmTimeout specifies the time-out value, in milliseconds, to wait for a response message for the two-way LM test. Upon expiration of the timeout period, the agent assumes that the respo…	millisecondsUnsigned32r/w Constraints: range: 1000-10000	.1.3.6.1.4.1.7483.6.1.2.52.7.8.1.6

tnDot1agCfmMepOndemandLmTestRsltTable consists of the results of manually
triggered on-demand regular Loss Measurement tests.

tnDot1agCfmMepOndemandLmTestRsltEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.9.1

tnDot1agCfmMepOndemandLmTestRsltEntry contains the results of a
manually triggered on-demand regular Loss Measurement (LM) test.
Rows are auto-generated by the system based on the
issuing of a on-demand regular LM test.

Indexes

IEEE8021-CFM-MIBdot1agCfmMdIndex IEEE8021-CFM-MIBdot1agCfmMaIndex IEEE8021-CFM-MIBdot1agCfmMepIdentifier

Column	Syntax	OID
tnDot1agCfmMepOndemandLmTnTF The value of tnDot1agCfmMepOndemandLmTnTF indicates the total number of near-end transmitted service frames from the remote node during the execution of the test.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.9.1.1
tnDot1agCfmMepOndemandLmTnLF The value of tnDot1agCfmMepOndemandLmTnLF indicates the total number of near-end lost service frames on the local node during the execution of the test.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.9.1.2
tnDot1agCfmMepOndemandLmTfTF The value of tnDot1agCfmMepOndemandLmTfTF indicates the total number of far-end transmitted service frames from the local node during the execution of the test.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.9.1.3
tnDot1agCfmMepOndemandLmTfLF The value of tnDot1agCfmMepOndemandLmTfLF indicates the total number of far-end lost service frames on the remote node during the execution of the test.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.9.1.4
tnDot1agCfmMepOndemandLmUnack The value of tnDot1agCfmMepOndemandLmUnack indicates the number of unacknowledged lost LM packets during the execution of the test.	packetsSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.6.1.2.52.7.9.1.5
tnDot1agCfmMepOndemandLmRemoteMacAddr The MAC address of the remote node involved in the test.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.7483.6.1.2.52.7.9.1.6

The tnDot1agCfmMepOWDelayRsltExtTable indicates the near-end One-way
Delay result.
This table is not persistent over reboots of the chassis.

tnDot1agCfmMepOWDelayRsltExtEntry row .1.3.6.1.4.1.7483.6.1.2.52.7.10.1

The near-end one-way delay test result table.

Indexes

IEEE8021-CFM-MIBdot1agCfmMdIndex IEEE8021-CFM-MIBdot1agCfmMaIndex IEEE8021-CFM-MIBdot1agCfmMepIdentifier

Column	Syntax	OID
tnDot1agCfmMepOWDelayRsltExtTnFD The value of tnDot1agCfmMepOWDelayRsltExtTnFD indicates one-way near-end frame delay from remote MEP to local MEP. It is the amount of time, measured in microseconds, from when the test-frame was transmitted by the remo…	microsecondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.10.1.1
tnDot1agCfmMepOWDelayRsltExtTnFDV The value of tnDot1agCfmMepDelayVariation indicates the amount of near-end one-way time delay variation, measured in microseconds, from the two most recent near-end one-way time delay measurements	microsecondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.6.1.2.52.7.10.1.2