This document is the SNMP MIB module for the Nokia SROS implementation
of Satellites.
Copyright (c) 2014-2018 Nokia. All rights reserved. Reproduction of
this document is authorized on the condition that the foregoing
copyright notice is included.
This SNMP MIB module (Specification) embodies Nokia's
proprietary intellectual property. Nokia retains all
title and ownership in the Specification, including any
revisions.
Nokia grants all interested parties a non-exclusive license to use and
distribute an unmodified copy of this Specification in connection with
management of Nokia products, and without fee, provided this copyright
notice and license appear on all copies.
This Specification is supplied `as is', and Nokia makes no warranty,
either express or implied, as to the use, operation, condition, or
performance of the Specification.
e tmnxSatelliteOperStateChange notification is generated
when there is a change in tmnxHwOperState for the satellite.
[EFFECT] The satellite has changed states. The
tmnxSatNotifyFailureReason is only valid when tmnxHwOperState is
'failed (5)', and should otherwise be blank.
[RECOVERY] Contact Nokia customer support if
tmnxSatNotifyFailureReason does not provide enough information to
rectify the situation.
tmnxSatSyncIfTimRef2Alarm
.1.3.6.1.4.1.6527.3.1.3.103.0.10
e tmnxSatSyncIfTimRef2Alarm notification is generated when
an alarm condition on the second timing reference is detected.
[EFFECT] If the other timing reference is free of faults, the
satellite no longer has a backup timing reference. If the other timing
reference also has a fault, the satellite will likely no longer be
synchronous with the host.
[RECOVERY] Investigate the state of the link between the host and the
satellite (i.e. the uplink) that drives the second timing reference on
the satellite for faults.
tmnxSatSyncIfTimRef2AlarmClear
.1.3.6.1.4.1.6527.3.1.3.103.0.11
e tmnxSatSyncIfTimRef1AlarmClear notification is generated
when the alarm condition on the second timing reference is cleared.
[EFFECT] This notification is for informational purposes only.
[RECOVERY] No recovery required.
tmnxSatLocalForwardStateChg
.1.3.6.1.4.1.6527.3.1.3.103.0.16
e tmnxSatLocalForwardStateChg notification is generated when
the system detects a change in the administrative state, or
operational state of the satellite local forward.
[EFFECT] The administrative state or operational state of the
satellite local forward has changed.
[RECOVERY] If the administrative state is 'inService (2)', and the
operational state is 'down (2)', check to ensure valid configuration
of the satellite local forward, and verify the connection of the
satellite to the host. Contact Nokia customer support if the issue
cannot be resolved.
tmnxSatLocalForwardSapStateChg
.1.3.6.1.4.1.6527.3.1.3.103.0.17
e tmnxSatLocalForwardSapStateChg notification is generated
when the system detects a change in the administrative state, or
operational state of the satellite local forward SAP.
[EFFECT] The administrative state or operational state of the
satellite local forward SAP has changed.
[RECOVERY] If the administrative state is 'inService (2)', and the
operational state is 'down (2)', check to ensure valid configuration
of the satellite local forward SAP, and verify the connection of the
satellite to the host. Contact Nokia customer support if the issue
cannot be resolved.
tmnxSatSyncIfTimRefSwitch
.1.3.6.1.4.1.6527.3.1.3.103.0.2
e tmnxSatSyncIfTimRefSwitch notification is generated when
there is a change of which timing reference is providing timing for
the satellite.
[EFFECT] This notification is for informational purposes only.
[RECOVERY] No recovery required.
tmnxSatSyncIfTimSystemQuality
.1.3.6.1.4.1.6527.3.1.3.103.0.3
SyncIfTimingSystemQuality notification is generated when
there is a change in the system timing quality level for the
satellite. This notification is a point-in-time state change event.
[CAUSE] This notification may be triggered for the following reasons:
1) There has been a switch in the timing reference in use by the
network element, either because the previously active timing
reference was disqualified, or to ensure that the network element
is using the timing reference with the best timing quality.
2) There has been a change in the active timing reference's quality
and the change does not result in a timing reference switch.
3) The network element has transitioned into or out of the holdover
state.
[EFFECT] The system quality level is used to determine the SSM code
transmitted on synchronous interfaces. This may affect the SSM code
transmitted on some or all interfaces, which may affect the
distribution of timing throughout the network.
[RECOVERY] If the customer is expecting the system to be locked to a
reference of a particular quality and the system quality has
decreased, the customer will need to determine the root cause (for
example, loss of communication with a satellite) and resolve the
issue.
tmnxSatSyncIfTimRef1Quality
.1.3.6.1.4.1.6527.3.1.3.103.0.4
e tmnxSatSyncIfTimRef1Quality notification is generated when
the received quality level changes on the first timing reference of
the satellite.
[EFFECT] This notification is for informational purposes only.
[RECOVERY] No recovery required.
tmnxSatSyncIfTimRef2Quality
.1.3.6.1.4.1.6527.3.1.3.103.0.5
e tmnxSatSyncIfTimRef2Quality notification is generated when
the received quality level changes on the second timing reference of
the satellite.
[EFFECT] This notification is for informational purposes only.
[RECOVERY] No recovery required.
tmnxSatSyncIfTimHoldover
.1.3.6.1.4.1.6527.3.1.3.103.0.6
e tmnxSatSyncIfTimHoldover notification is generated when
the synchronous equipment timing subsystem of the satellite
transitions into a holdover state.
[EFFECT] The transmit timing of all synchronous interfaces on the
satellite are no longer synchronous with the host. This could result
in traffic loss.
[RECOVERY] Investigate the state of the two input timing references on
the satellite and the links between the host and the satellite (i.e.
the uplinks) that drive them for failures.
tmnxSatSyncIfTimHoldoverClear
.1.3.6.1.4.1.6527.3.1.3.103.0.7
e tmnxSatSyncIfTimHoldoverClear notification is generated
when the synchronous equipment timing subsystem of the satellite
transitions out of the holdover state.
[EFFECT] This notification is for informational purposes only.
[RECOVERY] No recovery required.
tmnxSatSyncIfTimRef1Alarm
.1.3.6.1.4.1.6527.3.1.3.103.0.8
e tmnxSatSyncIfTimRef1Alarm notification is generated when
an alarm condition on the first timing reference is detected.
[EFFECT] If the other timing reference is free of faults, the
satellite no longer has a backup timing reference. If the other timing
reference also has a fault, the satellite will likely no longer be
synchronous with the host.
[RECOVERY] Investigate the state of the link between the host and the
satellite (i.e. the uplink) that drives the first timing reference on
the satellite for faults.
tmnxSatSyncIfTimRef1AlarmClear
.1.3.6.1.4.1.6527.3.1.3.103.0.9
e tmnxSatSyncIfTimRef1AlarmClear notification is generated
when the alarm condition on the first timing reference is cleared.
[EFFECT] This notification is for informational purposes only.
[RECOVERY] No recovery required.