SUPERMICRO-SNOOP-MIB Table View

This table contains multicast forwarding mode configuration
for each instance running in the snooping switch

fsSnoopInstanceGlobalEntry row .1.3.6.1.4.1.10876.101.1.105.2.1.1

This table contains instance number and the multicast
forwarding mode configuration for the particular instance

Indexes

fsSnoopInstanceGlobalInstId

Column	Syntax	OID
fsSnoopInstanceGlobalInstId Instance ID pertaining to the global configuration entry.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.105.2.1.1.1
fsSnoopInstanceGlobalMcastFwdMode Indicates the mode to be used for building the forwarding table i.e, whether IP based or MAC address based. The hardware should support programming of S,G and *,G entries for IGS/MLDS to operate in 'ipbased' mode. If…	Enumerationr/w Enumerated Values: 1 ipbased 2 macbased	.1.3.6.1.4.1.10876.101.1.105.2.1.1.2
fsSnoopInstanceGlobalSystemControl Snooping module is shutdown or started through this object. When set to 'start', resources required by the SNOOP module is allocated and the module starts running. When set to 'shutdown', all the resources are rele…	Enumerationr/w Enumerated Values: 1 start 2 shutdown	.1.3.6.1.4.1.10876.101.1.105.2.1.1.3
fsSnoopInstanceGlobalLeaveConfigLevel A global configuration to specify if the leave processing mechanism needs to be configured at the vlan level or at the port level. When this object is set to vlanbased, the mib object fsSnoopVlanFastLeave must be used…	Enumerationr/w Enumerated Values: 1 vlanbased 2 portbased	.1.3.6.1.4.1.10876.101.1.105.2.1.1.4
fsSnoopInstanceGlobalEnhancedMode This object is used to enable or disable the snooping module functioning in the enhanced mode. By default, the snooping module operates in the normal or default mode. In the default mode, the module mul…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.1.105.2.1.1.5
fsSnoopInstanceGlobalReportProcessConfigLevel A global configuration to specify if the report processing mechanism needs to be configured for the non-router ports or at the all ports level. When this object is set to non-router ports, the incoming report messages a…	Enumerationr/w Enumerated Values: 1 nonrouterports 2 allports	.1.3.6.1.4.1.10876.101.1.105.2.1.1.6
fsSnoopInstanceGlobalSparseMode This object is used to enable or disable the snooping module functioning in the sparse mode. By default, the snooping module operates in the non-sparse mode. In the non-sparse mode, the module will be us…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.1.105.2.1.1.7
fsSnoopInstanceGlobalMulticastFilterStatus This object is used to enable/disable the IGS multicast filtering feature. Interface mapping configurations will not be affected by this object status.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.1.1.8

This table contains global configuration of snooping for each 
instance running in switch

fsSnoopInstanceConfigEntry row .1.3.6.1.4.1.10876.101.1.105.2.2.1

This table contains instance number, address type and the list of
global configuration for the particular instance and address type

Indexes

fsSnoopInstanceConfigInstId fsSnoopInetAddressType

Column	Syntax	OID
fsSnoopInstanceConfigInstId Instance ID pertaining to the global configuration entry.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.105.2.2.1.1
fsSnoopInetAddressType Inet Address Type corresponding to the global configuration entry. This indicates whether the row is for IGMP/MLD Snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.2.2.1.2
fsSnoopStatus Enables or disables IGMP/MLD snooping in the system. When set to 'enabled', the IGS/MLDS module starts protocol operations. When set to 'disabled', the IGS/MLDS module stops performing protocol operations.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.3
fsSnoopProxyReportingStatus Enables or disables proxy-reporting in the system. When proxy-reporting is 'enabled' the switch generates reports and forwards them to the router based on the available host information. When proxy-reporting is 'disab…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.4
fsSnoopRouterPortPurgeIntervaldeprecated This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router p…	Integer32r/w Constraints: range: 60-600	.1.3.6.1.4.1.10876.101.1.105.2.2.1.5
fsSnoopPortPurgeIntervaldeprecated This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received, this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever…	Integer32r/w Constraints: range: 130-1225	.1.3.6.1.4.1.10876.101.1.105.2.2.1.6
fsSnoopReportForwardInterval This timer is used when both proxy and proxy-reporting is disabled. The switch then has to suppress multiple IGMPv2/ MLDv1 report messages for the same group from being forwarded to the router. This is the interval (…	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.10876.101.1.105.2.2.1.7
fsSnoopRetryCount In proxy/proxy-reporting mode, when the switch receives leave message on a port, it sends group specific query to check if there are any other interested v2 receivers for the group. This attribute defines the maximum…	Integer32r/w Constraints: range: 1-5	.1.3.6.1.4.1.10876.101.1.105.2.2.1.8
fsSnoopGrpQueryInterval The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there are any intersted receivers. The switch will send 'fsSnoopRetryCount' queries bef…	Integer32r/w Constraints: range: 2-5	.1.3.6.1.4.1.10876.101.1.105.2.2.1.9
fsSnoopReportFwdOnAllPorts In snooping mode, Snooping module will forward reports only on router ports by default. This object provides administrative control either to forward the reports on all the member ports of the VLAN or to forward the r…	Enumerationr/w Enumerated Values: 1 allports 2 rtrports 3 nonedgeports	.1.3.6.1.4.1.10876.101.1.105.2.2.1.10
fsSnoopTraceOption This object is used to enable trace statements in snooping module. A four byte integer is used for enabling the trace level. Each bit in the four byte integer represents a particular trace level. The mapping be…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.105.2.2.1.11
fsSnoopOperStatus The operational status of the IGS/MLDS protocol. The value enabled(1) indicates the IGS/MLDS module is currently enabled in the system. The value disable(1) indicates the IGS/MLDS module is currently disabled in the sys…	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.12
fsSnoopSendQueryOnTopoChange The Snooping Switch can be configured to send IGMP/MLD General queries on all non router ports when spanning tree topology change occurs in a network. If the spanning tree mode is RSTP, IGMP/MLD general queries will b…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.13
fsSnoopSendLeaveOnTopoChange The Snooping Switch can be configured to issue an IGMP proxy query solicitation on network ports, i.e. an IGMP Group Leave with group address 0.0.0.0. This will indicate to the upstream router that it immediately nee…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.14
fsSnoopFilterStatus This object is used to enable/disable the IGS filtering feature. Interface mapping configurations will not be affected by this object status. When this object is disabled, filters will not be applied in this instance …	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.15
fsSnoopMulticastVlanStatus This object is used to enable/disable the Multicast VLAN feature. When Multicast VLAN feature is enabled, each incoming untagged report or leave message will be classified to an M-VLAN, depending on whether any M-VLA…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.16
fsSnoopProxyStatus This object enables or disables Proxy in the system. Proxy can be enabled only if Proxy-reporting is disabled. In proxy mode, the switch act as querier for all downstream interfaces, act as host for all upstream…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.2.2.1.17
fsSnoopQueryFwdOnAllPorts In proxy and proxy reporting mode, Snooping module will send query messages only to the non-router ports by default. This object provides administrative control to forward the query messages on all the member ports of …	Enumerationr/w Enumerated Values: 1 allports 2 nonrtrports	.1.3.6.1.4.1.10876.101.1.105.2.2.1.18
fsSnoopFwdGroupsCnt Provide Forwarding DataBase Group Count for Particular instance and Address Type.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.105.2.2.1.19

This table contains MAC based multicast forwarding 
information. This information is applicable only if
the 'fsSnoopMcastForwardingMode' is set to 'macbased'

fsSnoopVlanMcastMacFwdEntry row .1.3.6.1.4.1.10876.101.1.105.3.1.1

This table contains VLAN ID, multicast group MAC address and the
list of ports onto which the multicast data packets for group
should be forwarded.

Indexes

fsSnoopVlanMcastMacFwdInstId fsSnoopVlanMcastMacFwdVlanId fsSnoopVlanMcastMacFwdInetAddressType fsSnoopVlanMcastMacFwdGroupAddress

Column	Syntax	OID
fsSnoopVlanMcastMacFwdInstId Instance ID pertaining to the Multicast forwarding entry.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.105.3.1.1.1
fsSnoopVlanMcastMacFwdVlanId VLAN ID pertaining to the Multicast forwarding entry	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.10876.101.1.105.3.1.1.2
fsSnoopVlanMcastMacFwdInetAddressType InetAddressType pertaining to the Multicast forwarding entry	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.3.1.1.3
fsSnoopVlanMcastMacFwdGroupAddress Multicast group MAC address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.10876.101.1.105.3.1.1.4
fsSnoopVlanMcastMacFwdPortList List of ports onto which the multicast data packets destined for this group will be forwarded.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.1.1.5
fsSnoopVlanMcastMacFwdLocalPortList List of ports onto which the multicast data packets destined for this group will be forwarded. Each bit in this object represent interfaces denoted by the object fsVcHlPortId associated to the instance identifier den…	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.1.1.6
fsSnoopVlanMcastMacFwdEntryFlag This flag tell about the entry type: either it is a Static group entry or it is a Dynamic group entry	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.105.3.1.1.7

This table contains the list of ports through which 
a router, in a particular VLAN is reachable.

fsSnoopVlanRouterEntry row .1.3.6.1.4.1.10876.101.1.105.3.3.1

Contains the VLAN ID and list of ports on which
routers are present in the VLAN.

Indexes

fsSnoopVlanRouterInstId fsSnoopVlanRouterVlanId fsSnoopVlanRouterInetAddressType

Column	Syntax	OID
fsSnoopVlanRouterInstId Instance ID pertaining to the router port entry.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.105.3.3.1.1
fsSnoopVlanRouterVlanId VLAN ID of the ports through which router is reachable.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.10876.101.1.105.3.3.1.2
fsSnoopVlanRouterInetAddressType It indicates whether the row belongs to IGMP / MLD snooping.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.3.3.1.3
fsSnoopVlanRouterPortList List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. This object may not be sufficient to represent the ful…	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.3.1.4
fsSnoopVlanRouterLocalPortList List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically. Each bit in this object represent interfaces denoted by…	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.3.1.5

This table contains configuration of snooping
on specific Vlans. This Table is valid only when VLAN is  
enabled in the system.

fsSnoopVlanFilterEntry row .1.3.6.1.4.1.10876.101.1.105.3.4.1

Contains snooping status , version and fast leave
configuration for a specific VLAN.

Indexes

fsSnoopVlanFilterInstId fsSnoopVlanFilterVlanId fsSnoopVlanFilterInetAddressType

Column	Syntax	OID
fsSnoopVlanFilterInstId Instance ID pertaining to VLAN filter table entry.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.105.3.4.1.1
fsSnoopVlanFilterVlanId VLAN ID for which snooping configuration is to be done.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.10876.101.1.105.3.4.1.2
fsSnoopVlanFilterInetAddressType Indicates whether the row belongs to IGS/MLD snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.3.4.1.3
fsSnoopVlanSnoopStatus Enables or disables IGS/MLDS on that specific VLAN	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.3.4.1.4
fsSnoopVlanOperatingVersiondeprecated Indicates the operating version of the IGS/MLDS switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 3 i.e, V3(3) or MLD version 2 i.e, V2(2). This object is deprecated. Its functi…	Enumeration Enumerated Values: 1 v1 2 v2 3 v3	.1.3.6.1.4.1.10876.101.1.105.3.4.1.5
fsSnoopVlanCfgOperVersiondeprecated Indicates the operating version of the IGS/MLDS switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 3 i.e, V3(3) or MLD version 2 i.e., V2(2). The 'fsSnoopVlanCfgOperVersion' sho…	Enumerationr/w Enumerated Values: 1 v1 2 v2 3 v3	.1.3.6.1.4.1.10876.101.1.105.3.4.1.6
fsSnoopVlanFastLeave Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message the switch checks if they are any interested receivers for the group by sending a group specific query before removing…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.3.4.1.7
fsSnoopVlanQuerier Indicates whether the switch is configured as a querier in the VLAN	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.3.4.1.8
fsSnoopVlanCfgQuerier The snooping switch can be configured to send IGMP/MLD queries when IGMP/MLD routers are not present in the VLAN. When set to 'enabled' the switch will generate general query messages. The query messages will be supp…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.105.3.4.1.9
fsSnoopVlanQueryInterval This is the interval (in seconds) for which the switch sends general queries in proxy and proxy-reporting mode. In proxy-reporting mode, General queries will be sent on all downstream interfaces with this interval only…	Integer32r/w Constraints: range: 60-600	.1.3.6.1.4.1.10876.101.1.105.3.4.1.10
fsSnoopVlanRtrPortList List of ports which are configured statically as router ports. statically. This object may not be sufficient to represent the full set of interfaces in each switch instance in environments where the number of interfaces…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.105.3.4.1.11
fsSnoopVlanRowStatus The status of a row in the VLAN filter table. Using this object, new entries can be created in the VLAN filter table and the existing entries can be removed from the VLAN filter table	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.105.3.4.1.12
fsSnoopVlanStartupQueryCount The Startup Query Count is the number of Queries sent out on startup, separated by the Startup Query Interval. The default value is the Robustness.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.105.3.4.1.13
fsSnoopVlanStartupQueryInterval Interval between the general query messages sent by the switch during startup of querier election process. This value must be <= (Query Interval/4)	secondsInteger32r/w Constraints: range: 15-150	.1.3.6.1.4.1.10876.101.1.105.3.4.1.14
fsSnoopVlanOtherQuerierPresentInterval The Other Querier Present Interval is the length of time that must pass before a multicast router decides that there is no longer another multicast router which should be the querier. This value must be >= ((Robustne…	secondsInteger32r/w Constraints: range: 120-1235	.1.3.6.1.4.1.10876.101.1.105.3.4.1.15

This table contains the information about dynamically learnt
multicast groups and the ports on which they are learnt.
When enhanced mode is enabled this table will be populated 
with both Outer and Inner VLAN. When operating in the default 
mode this table will be populated with the Outer VLAN alone and 
the Inner VLAN will be considered to have a value of zero. When
the Snoop module receives a packet classified to a single VLAN
(such as the CVLAN in Customer Bridges, or SVLAN in 802.1ad
Bridges), then this single VLAN is considered to be the Outer 
VLAN and the Inner VLAN will have a value of zero.

fsSnoopVlanMcastGroupEntry row .1.3.6.1.4.1.10876.101.1.105.3.5.1

Contains the information learnt about a multicast group.

Indexes

fsSnoopVlanMcastGroupInstanceId fsSnoopVlanMcastGroupOuterVlanId fsSnoopVlanMcastGroupInetAddressType fsSnoopVlanMcastGroupAddress fsSnoopVlanMcastGroupInnerVlanId

Column	Syntax	OID
fsSnoopVlanMcastGroupInstanceId Instance Id pertaining to a particular virtual context.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.1.105.3.5.1.1
fsSnoopVlanMcastGroupOuterVlanId The outer vlan id on which the multicast group is learnt.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.10876.101.1.105.3.5.1.2
fsSnoopVlanMcastGroupInetAddressType Inet Address Type corresponding to this group entry. This indicates whether the row is for IGMP/MLD Snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.3.5.1.3
fsSnoopVlanMcastGroupAddress The Multicast group address learnt.	OctetString Constraints: range: 16-16	.1.3.6.1.4.1.10876.101.1.105.3.5.1.4
fsSnoopVlanMcastGroupInnerVlanId The inner vlan id on which the multicast group is learnt.	InnerVlanIndex Type Constraints: range: 0..4094	.1.3.6.1.4.1.10876.101.1.105.3.5.1.5
fsSnoopVlanMcastGroupPortList The list of interfaces on which the group entry is learnt. statically. This object may not be sufficient to represent the full set of interfaces in each switch instance in environments where the number of interfaces in …	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.5.1.6
fsSnoopVlanMcastGroupLocalPortList The list of interfaces on which the group entry is learnt. Each bit in this object represent interfaces denoted by the object fsVcHlPortId associated to the instance identifier denoted by fsSnoopVlanMcastGroupInstanc…	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.5.1.7

This table contains the information about dynamically
learnt multicast groups, the source ip of the hosts 
sending the multicast reports and the registered sources
from which the multicast data is requested.

fsSnoopVlanMcastReceiverEntry row .1.3.6.1.4.1.10876.101.1.105.3.6.1

Contains an entry for each multicast report sent by each host
for a multicast group and requesting data from a specific
source.

Indexes

fsSnoopVlanMcastGroupInstanceId fsSnoopVlanMcastGroupOuterVlanId fsSnoopVlanMcastGroupInetAddressType fsSnoopVlanMcastGroupAddress fsSnoopVlanMcastGroupInnerVlanId fsSnoopVlanMcastReceiverPortIndex fsSnoopVlanMcastReceiverHostAddress fsSnoopVlanMcastReceiverSourceAddress

Column	Syntax	OID
fsSnoopVlanMcastReceiverPortIndex The interface on which the multicast group address is learnt.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.105.3.6.1.1
fsSnoopVlanMcastReceiverHostAddress The IP address of the multicast receiver that has sent the multicast report to join this group.	OctetString Constraints: range: 16-16	.1.3.6.1.4.1.10876.101.1.105.3.6.1.2
fsSnoopVlanMcastReceiverSourceAddress Unicast source address of the data source that sends multicast data for this group	OctetString Constraints: range: 16-16	.1.3.6.1.4.1.10876.101.1.105.3.6.1.3
fsSnoopVlanMcastReceiverFilterMode The include or the exclude mode that has been registered by the multicast receiver for the unicast source address specified.	Enumeration Enumerated Values: 1 include 2 exclude	.1.3.6.1.4.1.10876.101.1.105.3.6.1.4

This table contains IP multicast forwarding information 
based on both Outer VLAN and Inner VLAN.                 
          
When enhanced mode is enabled this table will be populated 
with both Outer and Inner VLAN. When operating in the default mode 
this table will be populated with the Outer VLAN alone and the 
Inner VLAN will be considered to have a value of zero. When
the Snoop module receives a packet classified to a single VLAN
(such as the CVLAN in Customer Bridges, or SVLAN in 802.1ad
Bridges), then this single VLAN is considered to be the Outer VLAN
and the Inner VLAN will have a value of zero. 
          
The information present in this table is applicable only if the 
object 'fsSnoopInstMcastForwardingMode' is set to 'ip-based'.

fsSnoopVlanIpFwdEntry row .1.3.6.1.4.1.10876.101.1.105.3.7.1

This table contains Outer VLAN ID, unicast source address,
multicast group address, Inner VLAN ID and the list of ports onto
which the multicast data packets for the group should be
forwarded.

Indexes

fsSnoopVlanIpFwdInstanceId fsSnoopVlanIpFwdOuterVlanId fsSnoopVlanIpFwdInetAddressType fsSnoopVlanIpFwdSourceAddress fsSnoopVlanIpFwdGroupAddress fsSnoopVlanIpFwdInnerVlanId

Column	Syntax	OID
fsSnoopVlanIpFwdInstanceId Instance Id pertaining to a particular virtual context.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.1.105.3.7.1.1
fsSnoopVlanIpFwdOuterVlanId The outer vlan id on which the multicast group is learnt.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.10876.101.1.105.3.7.1.2
fsSnoopVlanIpFwdInetAddressType Inet Address Type corresponding to this forwarding table entry. This indicates whether the row is for IGMP/MLD Snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.3.7.1.3
fsSnoopVlanIpFwdSourceAddress Unicast source address of the data source that sends multicast data for this group	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.10876.101.1.105.3.7.1.4
fsSnoopVlanIpFwdGroupAddress The Multicast group address learnt.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.10876.101.1.105.3.7.1.5
fsSnoopVlanIpFwdInnerVlanId The inner vlan id on which the multicast group is learnt.	InnerVlanIndex Type Constraints: range: 0..4094	.1.3.6.1.4.1.10876.101.1.105.3.7.1.6
fsSnoopVlanIpFwdPortList List of ports onto which the multicast data packets from this source, destined for this group, will be forwarded statically. This object may not be sufficient to represent the full set of interfaces in each switch in…	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.7.1.7
fsSnoopVlanIpFwdLocalPortList List of ports onto which the multicast data packets from this source destined for this group, will be forwarded. Each bit in this object represent interfaces denoted by the object fsVcHlPortId associated to the insta…	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.105.3.7.1.8

This table is an extention table of fsSnoopVlanFilterTable

fsSnoopVlanFilterXEntry row .1.3.6.1.4.1.10876.101.1.105.3.8.1

Each entry contains configurations for specific VLANs

Indexes

No indexes recorded

Column	Syntax	OID
fsSnoopVlanBlkRtrPortList List of ports which are configured statically as blocked router ports statically. This object may not be sufficient to represent full set of interfaces in each switch instance in environments where the number of inte…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.105.3.8.1.1
fsSnoopVlanFilterMaxLimitType Indicates the type of limit to be applied on this VLAN. Setting as 'channels' indicates that the limit is set for channel (group, source) registrations whereas setting as 'groups' indicates that the limit is set for …	Enumerationr/w Enumerated Values: 0 none 1 groups 2 channels	.1.3.6.1.4.1.10876.101.1.105.3.8.1.2
fsSnoopVlanFilterMaxLimit Sets the maximum number of unique entries (channel or group) that can be learned simultaneously on this VLAN. The fsSnoopVlanFilterMaxLimitType must be set before configuring this object. If fsSnoopVlanFilterMaxLimit…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.3.8.1.3
fsSnoopVlanFilter8021pPriority Configures the priority with which the reports assigned to this VLAN should be processed by the hardware as well as by the upstream router. Priority 0 means lowest priority while priority 7 means highest priority. This …	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.10876.101.1.105.3.8.1.4
fsSnoopVlanFilterDropReports Some implementations might require that IGMPv1 should not be supported, as IGMPv1 does not have any group leaving mechanism. Some other implementations might require that both IGMPv1 and IGMPv2 reports should be dropped…	Enumerationr/w Enumerated Values: 0 none 1 igmpv1 2 igmpv2 3 all	.1.3.6.1.4.1.10876.101.1.105.3.8.1.5
fsSnoopVlanMulticastProfileId This object contains the multicast profile id configured for a particular VLAN and is used for multicast vlan classification. When any untagged report or leave message is received (i.e. packet with no tag in a Custome…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.3.8.1.6
fsSnoopVlanPortPurgeInterval This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received,this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.105.3.8.1.7
fsSnoopVlanMaxResponseTime The maximum response code advertised in queries send over this vlan.This object is used to configure max response code for both IGS and MLDS.Minimum value for the object is zero for both IGS and MLDS. Max value and defu…	Integer32r/w Constraints: range: 0-65025	.1.3.6.1.4.1.10876.101.1.105.3.8.1.8
fsSnoopVlanRtrLocalPortList List of ports which are configured statically as router ports. Each bit in this object represent interfaces denoted by the object fsVcHlPortId associated to the instance identifier denoted by fsSnoopVlanFilterInstId.…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.105.3.8.1.9
fsSnoopVlanBlkRtrLocalPortList List of ports which are configured statically as blocked router ports. Each bit in this object represent interfaces denoted by the object fsVcHlPortId associated to the instance identifier denoted by fsSnoopVlanFilte…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.105.3.8.1.10

This table contains IP based multicast forwarding 
information.

fsSnoopVlanStaticMcastGrpEntry row .1.3.6.1.4.1.10876.101.1.105.3.9.1

This table contains VLAN ID, unicast source address ,
multicast group address and the list of ports onto which the
multicast data packets for group should be forwarded.

Indexes

fsSnoopVlanStaticMcastGrpInstId fsSnoopVlanStaticMcastGrpVlanId fsSnoopVlanStaticMcastGrpAddressType fsSnoopVlanStaticMcastGrpSourceAddress fsSnoopVlanStaticMcastGrpGroupAddress

Column	Syntax	OID
fsSnoopVlanStaticMcastGrpInstId Instance ID pertaining to the Multicast forwarding entry. Currently only one instance is supported so it is always 1	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.10876.101.1.105.3.9.1.1
fsSnoopVlanStaticMcastGrpVlanId VLAN ID pertaining to the Multicast forwarding entry	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.10876.101.1.105.3.9.1.2
fsSnoopVlanStaticMcastGrpAddressType InetAddressType pertaining to the Multicast forwarding entry	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.3.9.1.3
fsSnoopVlanStaticMcastGrpSourceAddress Unicast source address of the data source that sends multicast data for this group	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.10876.101.1.105.3.9.1.4
fsSnoopVlanStaticMcastGrpGroupAddress IP/IPv6 multicast group address	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.10876.101.1.105.3.9.1.5
fsSnoopVlanStaticMcastGrpPortList List of ports onto which the multicast data packets destined for this source and group will be forwarded.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.105.3.9.1.6
fsSnoopVlanStaticMcastGrpRowStatus The row status variable, used according to row installation and removal conventions.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.105.3.9.1.7

This table contains snooping statistics  
maintained by the switch. The statistics are
maintained on a per VLAN basis.

fsSnoopStatsEntry row .1.3.6.1.4.1.10876.101.1.105.4.1.1

Contains snooping statistics for a particular VLAN.

Indexes

fsSnoopStatsInstId fsSnoopStatsVlanId fsSnoopStatsInetAddressType

Column	Syntax	OID
fsSnoopStatsInstId Instance ID pertaining for the statistics entry.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.105.4.1.1.1
fsSnoopStatsVlanId VLAN ID for which snooping statistics are displayed	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.10876.101.1.105.4.1.1.2
fsSnoopStatsInetAddressType Indicates whether the statistics are for IGS/MLDS	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.4.1.1.3
fsSnoopStatsRxGenQueries Provides the statistics of General Queries received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.4
fsSnoopStatsRxGrpQueries Provides the statistics of Group Specific Queries received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.5
fsSnoopStatsRxGrpAndSrcQueries Provides the statistics of Group and Source Specific Queries received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.6
fsSnoopStatsRxAsmReports Provides the statistics of IGMPv1/IGMPv2 Membership reports received by the snooping switch. In case of MLDS, it provides the statistics of MLDv1 membership reports.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.7
fsSnoopStatsRxSsmReports Provides the statistics of IGMPv3/MLDv2 Membership reports received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.8
fsSnoopStatsRxSsmIsInMsgs Provides the statistics of IGMPv3/MLDv2 Membership reports of type IS_IN received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.9
fsSnoopStatsRxSsmIsExMsgs Provides the statistics of IGMPv3/MLDv2 Membership reports of type IS_EX received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.10
fsSnoopStatsRxSsmToInMsgs Provides the statistics of IGMPv3/MLDv2 Membership reports of type TO_IN received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.11
fsSnoopStatsRxSsmToExMsgs Provides the statistics of IGMPv3/MLDv2 Membership reports of type TO_EX received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.12
fsSnoopStatsRxSsmAllowMsgs Provides the statistics of IGMPv3/MLDv2 Membership reports of type ALLOW received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.13
fsSnoopStatsRxSsmBlockMsgs Provides the statistics of IGMPv3/MLDv2 Membership reports of type BLOCK received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.14
fsSnoopStatsRxAsmLeaves Provides the statistics of IGMPv2/MLDv1 Leave messages received by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.15
fsSnoopStatsTxGenQueries Provides the statistics of General Queries transmitted by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.16
fsSnoopStatsTxGrpQueries Provides the statistics of Group Specific Queries transmitted by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.17
fsSnoopStatsTxGrpAndSrcQueries Provides the statistics of Group and Source Specific Queries transmitted by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.18
fsSnoopStatsTxAsmReports Provides the statistics of IGMPv1/IGMPv2 Membership reports transmitted by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.19
fsSnoopStatsTxSsmReports Provides the statistics of IGMPv3/MLDv2 Membership reports transmitted by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.20
fsSnoopStatsTxAsmLeaves Provides the statistics of IGMPv2/MLDv1 Leave messages transmitted by the snooping switch.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.21
fsSnoopStatsDroppedPkts Provides the number of erroneous IGMP/MLD packets dropped by the snooping switch due to failure in checksum calculation.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.22
fsSnoopStatsUnsuccessfulJoins Provides the total number of IGMP groups or channels dropped, because the maximum limit of groups or channels allowed for the VLAN has been reached. By default, this object is for groups, but if fsSnoopVlanFilterMaxL…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.23
fsSnoopStatsActiveJoins Provides the total number of IGMP groups or channels active on this VLAN at the given time. By default, this object is for groups, but if fsSnoopVlanFilterMaxLimitType is 'channels' this object is for channels (S,G) …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.24
fsSnoopStatsActiveGroups Provides the total number of IGMP groups or channels active on this VLAN at the given time.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.4.1.1.25

This table contains Port-related configurable information.
This table is applicable only when the snooping module is 
operating in the default Mode. This table MUST NOT be 
configured when the snooping module is operating in the 
enhanced mode.

fsSnoopPortEntry row .1.3.6.1.4.1.10876.101.1.105.5.1.1

This table contains the list of paramter/attribute objects
that can be configured on a port.

Indexes

fsSnoopPortIndex fsSnoopPortInetAddressType

Column	Syntax	OID
fsSnoopPortIndex The interface index of the port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.105.5.1.1.1
fsSnoopPortInetAddressType Inet Address Type corresponding to this interface configuration entry. This indicates whether the row is for IGMP/MLD Snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.5.1.1.2
fsSnoopPortLeaveMode Sets the mechanism to be used for processing the leave messages in the down stream interface. When this object is set to 'explicitHostTrack', then the leave messages are processed using the explicit hos…	Enumerationr/w Enumerated Values: 1 explicithosttrack 2 fastleave 3 normalleave	.1.3.6.1.4.1.10876.101.1.105.5.1.1.3
fsSnoopPortRateLimit Configures the rate-limit for a downstream interface in units of the number of IGMP packets per second. By default, this object will hold the maximum value supported by an unsigned integer and will not rate limit any…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.1.1.4
fsSnoopPortMaxLimitType Indicates the type of limit to be applied on this interface. Setting as 'channels' indicates that the limit is set for channel (group, source) registrations whereas setting as 'groups' indicates that the limit is set…	Enumerationr/w Enumerated Values: 0 none 1 groups 2 channels	.1.3.6.1.4.1.10876.101.1.105.5.1.1.5
fsSnoopPortMaxLimit Configures the maximum number of unique entries (channel or group) that can be learned simultaneously on this interface. The fsSnoopPortMaxLimitType must be set before configuring this object. However the Max-limit i…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.1.1.6
fsSnoopPortProfileId The multicast profile index configured for the downstream interface. This profile contains a set of allowed or denied rules which are to be applied for the IGMP packets received through this downstream interface. By …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.1.1.7
fsSnoopPortMemberCnt Provides the total number of groups or channels active on the interface at the given time.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.1.1.8
fsSnoopPortMaxBandwidthLimit Sets the Maximum bandwidth allowed on this port for Multicast. The fsSnoopPortMaxLimitType must be set before configuring this object. If the fsSnoopPortMaxLimitType is 'channels', this limit applies to the bandwidth …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.1.1.9
fsSnoopPortDropReports This object decides whether to process or drop the IGMP reports coming on this port.	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.10876.101.1.105.5.1.1.10
fsSnoopPortRowStatus The status of a row in the Port Config table. Using this object, new entries can be created or existing entries can be removed from the Port Config Table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.105.5.1.1.11

This table contains Port-related configurable information.
This table is applicable only when the snooping module is 
operating in the enhanced Mode. This table MUST NOT be 
configured when the snooping module is operating in the 
default mode.

fsSnoopEnhPortEntry row .1.3.6.1.4.1.10876.101.1.105.5.2.1

This table contains the list of paramter/attribute objects that
can be configured on an interface.

Indexes

fsSnoopEnhPortIndex fsSnoopEnhPortInnerVlanId fsSnoopEnhPortInetAddressType

Column	Syntax	OID
fsSnoopEnhPortIndex The interface index of the port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.105.5.2.1.1
fsSnoopEnhPortInnerVlanId The Inner VLAN Identifier.	InnerVlanIndex Type Constraints: range: 0..4094	.1.3.6.1.4.1.10876.101.1.105.5.2.1.2
fsSnoopEnhPortInetAddressType Inet Address Type corresponding to this interface configuration entry. This indicates whether the row is for IGMP/MLD Snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.5.2.1.3
fsSnoopEnhPortLeaveMode Sets the mechanism to be used for processing the leave messages in the down stream interface. When this object is set to 'explicitHostTrack', then the leave messages are processed using the explicit hos…	Enumerationr/w Enumerated Values: 1 explicithosttrack 2 fastleave 3 normalleave	.1.3.6.1.4.1.10876.101.1.105.5.2.1.4
fsSnoopEnhPortRateLimit Configures the rate-limit for a downstream interface in units of the number of IGMP packets per second. By default, this object will hold the maximum value supported by an unsigned integer and will not rate limit any…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.2.1.5
fsSnoopEnhPortMaxLimitType Indicates the type of limit to be applied on this interface. Setting as 'channels' indicates that the limit is set for channel (group, source) registrations whereas setting as 'groups' indicates that the limit is set…	Enumerationr/w Enumerated Values: 0 none 1 groups 2 channels	.1.3.6.1.4.1.10876.101.1.105.5.2.1.6
fsSnoopEnhPortMaxLimit Configures the maximum number of unique entries (channel or group) that can be learned simultaneously on this interface. The fsSnoopEnhPortMaxLimitType must be set before configuring this object. However the Max-limi…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.2.1.7
fsSnoopEnhPortProfileId The multicast profile index configured for the downstream interface. This profile contains a set of allowed or denied rules which are to be applied for the IGMP packets received through this downstream interface. By …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.2.1.8
fsSnoopEnhPortMemberCnt Provides the total number of groups or channels active on the interface at the given time.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.2.1.9
fsSnoopEnhPortMaxBandwidthLimit Sets the Maximum bandwidth allowed on this port for Multicast. The fsSnoopEnhPortMaxLimitType must be set before configuring this object. If the fsSnoopEnhPortMaxLimitType is 'channels', this limit applies to the band…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.105.5.2.1.10
fsSnoopEnhPortDropReports This object decides whether to process or drop the IGMP reports coming on this port.	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.10876.101.1.105.5.2.1.11
fsSnoopEnhPortRowStatus The status of a row in the Port Config table. Using this object, new entries can be created or existing entries can be removed from the Port Config Table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.105.5.2.1.12

This table contains upstream Router Port-related
configurable information. Router port entry in this table 
will be created when the router port is either learnt 
dynamically or when the router port is statically 
configured through 'fsSnoopVlanRtrPortList'.Only static
router ports will be restored during save restore.

fsSnoopRtrPortEntry row .1.3.6.1.4.1.10876.101.1.105.5.3.1

This table contains the upstream router port operating
and configured version of IGMP.

Indexes

fsSnoopRtrPortIndex fsSnoopRtrPortVlanId fsSnoopRtrPortInetAddressType

Column	Syntax	OID
fsSnoopRtrPortIndex The interface index of the port which is defined as an upstream router port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.105.5.3.1.1
fsSnoopRtrPortVlanId The VLAN Identifier for the upstream router port	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.10876.101.1.105.5.3.1.2
fsSnoopRtrPortInetAddressType Inet Address Type corresponding to the global configuration entry. This indicates whether the row is for IGMP/MLD Snooping	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.105.5.3.1.3
fsSnoopRtrPortOperVersion Indicates the operating version of the IGMP Proxy on the upstream router port. Operating version is used by the Proxy to send consolidated reports on the router ports. Operating version of the router port will change b…	Enumeration Enumerated Values: 1 v1 2 v2 3 v3	.1.3.6.1.4.1.10876.101.1.105.5.3.1.4
fsSnoopRtrPortCfgOperVersion Indicates the configured version of the IGMP Proxy on the upstream router port.The default operating mode is IGMP version 3 i.e, V3(3) or MLD version 2 i.e, V2(2). The 'fsSnoopRtrPortCfgOperVersion' should be configure…	Enumerationr/w Enumerated Values: 1 v1 2 v2 3 v3	.1.3.6.1.4.1.10876.101.1.105.5.3.1.5
fsSnoopOlderQuerierInterval The time interval after which proxy assumes that there are no v1/v2 routers present on the upstream port.While OlderQuerierTimer is running, proxy will reply to all queries with consolidated v1/v2 (oper version) repor…	Integer32r/w Constraints: range: 60-600	.1.3.6.1.4.1.10876.101.1.105.5.3.1.6
fsSnoopV3QuerierInterval The time interval after which proxy assumes that there are no IGMPv3 routers present on the upstream port.While V3QuerierTimer is running, proxy will reply to all queries with consolidated v1/v2/v3 (oper version) rep…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.105.5.3.1.7

This augment table contains additional objects
for fsSnoopRtrPortTable.

fsXSnoopRtrPortEntry row .1.3.6.1.4.1.10876.101.1.105.5.4.1

This table contains management information applicable to
an interface.

Indexes

No indexes recorded

Column	Syntax	OID
fsXSnoopRtrPortRowStatus The Row status of this entry which is used only in two scenarios. 1. CREATE_AND_WAIT 2. DESTROY. Where '1' will be used during port creation and '2' will be used during port deletion.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.105.5.4.1.1

This table is used to notify the error occurred, when an NPAPI call  
invoked from the Snooping module fails, in the form of a trap

fsSnoopTrapObjectsEntry row .1.3.6.1.4.1.10876.101.1.105.6.5.1

This entry is used to store the notification information

Indexes

No indexes recorded

Column	Syntax	OID
fsSnoopTrapHwErrType Indicates the type of hardware call that failed.	Enumeration Enumerated Values: 0 hardwareCreate 1 hardwareDelete 2 hardwarePortAdd 3 hardwarePortDelete	.1.3.6.1.4.1.10876.101.1.105.6.5.1.1