SUPERMICRO-ISS-MIB Table View

A table to control device features like egress traffic control,
stats collection, etc. either for the entire switch or for each
interface in the switch.

issConfigCtrlEntry row .1.3.6.1.4.1.10876.101.1.81.2.1.1

An entry appears in this table for each interface in the system.

In addition to that an entry with index '0' is created in this
table by default.

If 'issConfigCtrlStatus' of the entry '0' is ma…

Indexes

issConfigCtrlIndex

Column	Syntax	OID
issConfigCtrlIndex Interface index of the port for which the configuration in this entry applies. If any configuration is made in this table for the index '0', that configuration will be considered as global configuration …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.1.81.2.1.1.1
issConfigCtrlEgressStatus Controls the transmission of egress traffic over this interface. This value for entry '0' controls the egress traffic over all interfaces.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.81.2.1.1.2
issConfigCtrlStatsCollection Enables or disables statistics collection for this interface. This value for entry '0' controls the stats collection for all interfaces.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.81.2.1.1.3
issConfigCtrlStatus Speficies the validity of the entry. If the 'Config Control Status' for entry '0' is made 'valid', then global control is chosen in the system. It signifies that the values against entry '0' is applicable…	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.10876.101.1.81.2.1.1.4

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

issPortCtrlEntry row .1.3.6.1.4.1.10876.101.1.81.2.2.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

issPortCtrlIndex

Column	Syntax	OID
issPortCtrlIndex Interface index of the port for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.2.2.1.1
issPortCtrlMode Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates with the port on the other end of the link …	Enumerationr/w Enumerated Values: 1 auto 2 noNegotiation	.1.3.6.1.4.1.10876.101.1.81.2.2.1.2
issPortCtrlDuplex Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value f…	Enumerationr/w Enumerated Values: 1 full 2 half	.1.3.6.1.4.1.10876.101.1.81.2.2.1.3
issPortCtrlSpeed Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its pe…	Enumerationr/w Enumerated Values: 1 tenMBPS 2 hundredMBPS 3 oneGB 4 tenGB 5 fortyGB 6 fiftysixGB 7 twentyfivehundredMBPS 8 twentyfiveGB 9 fiftyGB 10 hundredGB 11 autoSpeed	.1.3.6.1.4.1.10876.101.1.81.2.2.1.4
issPortCtrlFlowControldeprecated Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negot…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.1.81.2.2.1.5
issPortCtrlRenegotiate When configured as 'true', restarts autonegotiation on the interface. Once autonegotiation is restarted, the value of this object reverts to 'false'.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.81.2.2.1.6
issPortCtrlMaxMacAddr Specifies the maximum number of new MAC addresses that can be learnt over the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.81.2.2.1.7
issPortCtrlMaxMacAction Specifies the action to be taken when the maximum number of new MAC addresses that can be learnt over the interface is exceeded. If the action is 'drop', the packet with new mac address will be dropped o…	Enumerationr/w Enumerated Values: 1 drop 2 purgeLRU	.1.3.6.1.4.1.10876.101.1.81.2.2.1.8
issPortHOLBlockPrevention Enables or disables Head-Of-Line Blocking prevention on a port.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.10876.101.1.81.2.2.1.9
issPortAutoNegAdvtCapBits A value uniquely identifies the set of capabilities advertised by the local auto negotiation entity other than the standard capabilities supported by ifMauAutoNegCapAdvertisedBits. When this object is needed to be confi…	OctetStringr/w	.1.3.6.1.4.1.10876.101.1.81.2.2.1.10
issPortCpuControlledLearning Enables or disables the CPU controlled learning on a port. The default behavior is hardware learning. By enabling this object software learning on that particular port is enabled. When CPU controlled le…	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.10876.101.1.81.2.2.1.11
issPortMdiOrMdixCap Specifies the port should be in Auto-Mdix mode or Mdi/Mdix. Setting the value to `auto` enables the Auto MDIX in the port - issPortCtrlIndex. This will be effective only when the speed of the particular p…	Enumerationr/w Enumerated Values: 1 auto 2 mdi 3 mdix	.1.3.6.1.4.1.10876.101.1.81.2.2.1.12
issPortCtrlFlowControlMaxRate Configures the maximum rate (kbps) - a high water mark beyond which pause frames will be generated to flow control the ingress traffic. This value should be set to 0 if no pause frame generation is required. In chipsets…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.10876.101.1.81.2.2.1.13
issPortCtrlFlowControlMinRate Configures the minimum rate (kbps) - a low water mark below which pause frames generation will be stopped. This value should be set to a value lesser that of 'issPortCtrlFlowControlMaxRate'. This value should be set …	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.10876.101.1.81.2.2.1.14

This table is used to configure the port isolation feature.
For a given port, user can configure the list of allowed
forwarding/egress ports, where the packets for particular vlan that 
ingress the port can be forwarded. If the Vlan is not given, then 
the rule will be applied for all packets that ingress the given port.
          
This table can be configured only for physical and link aggregated 
ports. 
          
Before a packet is sent out of a port (after all L2/L3 processing), port 
isolation table entry is referred for the ingress port of that packet. 
If an entry is present for that ingress port and if the outgoing port 
is configured as one of the egress ports , then the packet 
will be transmitted out of that outgoing port. Otherwise the packet 
will be dropped.
          
If there is no entry configured for that ingress port in this
table, then the packet will be transmitted on that outgoing port.

issPortIsolationEntry row .1.3.6.1.4.1.10876.101.1.81.2.3.1

Each etnry in this table gives a ingress port to egress port mapping.

Indexes

issPortIsolationIngressPort issPortIsolationInVlanId issPortIsolationEgressPort

Column	Syntax	OID
issPortIsolationIngressPort This object speficies the IfIndex of the ingress port. This port can be a physical or link aggregated port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.81.2.3.1.1
issPortIsolationInVlanId If this object value is non-zero, then the port isolation rule is applied for all packets received on the given ingress port. Otherwise the rule is applied for this vlan packets received on the given ingress port.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.10876.101.1.81.2.3.1.2
issPortIsolationEgressPort This object specifies one of the allowed egress ports for the given ingress port identified by the first index for this row. This port can be either a physical or link aggregated port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.81.2.3.1.3
issPortIsolationStorageType Indicates the storage type of this entry. Only 'volatile' and 'nonVolatile' values are allowed for this object. 'readOnly', 'permenant' and 'other' values are not allowed for this object. If this table …	SNMPv2-TCStorageType Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.10876.101.1.81.2.3.1.4
issPortIsolationRowStatus Denotes the Row Status for port isolation table entry. Only 'CreateAndGo' and 'destroy' values are allowed for this object. 'CreateAndWait' and 'notInService' values are not allowed. Example: To add ports 2, 3 as egr…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.81.2.3.1.5

A table to control the port split mode of the device

issSplitModeEntry row .1.3.6.1.4.1.10876.101.1.81.2.4.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

issSplitModeIndex

Column	Syntax	OID
issSplitModeIndex Interface index of the port for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.2.4.1.1
issSplitModeValue Speficies the setting in which split mode of the interface is determined. If set as 'off', Qx port will be turn on and related Ex ports will be turn off. If set as 'on', Ex ports will be tu…	Enumerationr/w Enumerated Values: 0 off 1 on 2 none	.1.3.6.1.4.1.10876.101.1.81.2.4.1.2

A table to control mirroring features for each interface 
in the switch.
          
Parameters in this table are valid only when the 
'issMirrorStatus' for the switch is not 'disabled'.

issMirrorCtrlEntry row .1.3.6.1.4.1.10876.101.1.81.3.3.1

An entry appears in this table for each interface
in the system.

Indexes

issMirrorCtrlIndex

Column	Syntax	OID
issMirrorCtrlIndex The interface index of the port for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.3.3.1.1
issMirrorCtrlIngressMirroring Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.81.3.3.1.2
issMirrorCtrlEgressMirroring Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.10876.101.1.81.3.3.1.3
issMirrorCtrlStatus Specifies the validity of the entry.	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.10876.101.1.81.3.3.1.4

This Table is used to configure advanced mirroring features like
- Port Based Mirroring:
- flow based mirroring
- vlan based mirroring
          
     Following are the configuration details for Port based mirroring:
         To configure source ports in a session
        - issMirrorCtrlExtnMirrType - is set to portBased
        - issMirrorCtrlExtnSrcTable - should be used to configure list
                                      of source ports to be mirrored 
                                      in a session
        - issMirrorCtrlExtnSrcId  - represents the source port. 
                                    The port Id to be mirrored 
                                    should be given here.
        - issMirrorCtrlExtnSrcCfg - this object is used to 
                                    add/remove a port in the 
                                    source port list 
          
        Example
        To create a session 1 with source ports 5,6 following 
        sequence of configuration should be followed
        For table issMirrorCtrlExtnTable
        issMirrorCtrlExtnSessionIndex = 1 as index
        issMirrorCtrlExtnMirrType = portBased
          
        For table issMirrorCtrlExtnSrcTable
        issMirrorCtrlExtnSessionIndex = 1 as index
        issMirrorCtrlExtnSrcId  = 5 as index
        issMirrorCtrlExtnSrcCfg = add
        issMirrorCtrlExtnSessionIndex = 1 as index
        issMirrorCtrlExtnSrcId  = 6 as index
        issMirrorCtrlExtnSrcCfg = add
                       
        To configure destination ports in a session
         - issMirrorCtrlExtnDestinationTable - should be used to 
                                               configure list of 
                                               destination ports to be 
                                               mirrored in a session
             - issMirrorCtrlExtnDestination  - represents the 
                                               destination port. The 
                                               port Id to which packets 
                                               should be mirrored should
                                               be given here.
             - issMirrorCtrlExtnDestCfg - this object is used to 
                                          add/remove a port in the 
                                          source port list. 
             Example
             To create a session 1 with destination port 10,11 following
             sequence of configuration should be followed
             For table issMirrorCtrlExtnTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnMirrType = portBased
          
             For table issMirrorCtrlExtnDestinationTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnDestination  = 10 as index
             issMirrorCtrlExtnDestCfg = add
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnDestination  = 11 as index
             issMirrorCtrlExtnDestCfg = add
          
        To Activate a session
         - issMirrorCtrlExtnStatus - should be used to 
                                     activate/deactivate mirroring for a
                                     session
             Example
             To enable mirroring for a session following sequence of 
             configuration should be followed        
             For table issMirrorCtrlExtnTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnStatus = active
          
         Above configurations applies to flow based mirroring also, the 
         issMirrorCtrlExtnSrcId used above for configuratin ports 
         should be used to configure flow Id
                   
        To enable remote monitoring of sources for a session
         - issMirrorCtrlExtnRSpanStatus - should be used to 
                                          enable/disable remote 
                                          monitoring for a session 
                                          it can be used to set a 
                                          session as source rspan 
                                          session which implies source 
                                          entities for this session are 
                                          monitored remotely or can be 
                                          used to set a session 
                                          as destination rspan session 
                                          which implies that mirrored 
                                          data is received for this 
                                          session should be forwarded to 
                                          destination entities of this 
                                          session
         - issMirrorCtrlExtnRSpanVlanId - it is the vlan id which is 
                                          reserved in the network to 
                                          carry Mirrored data,if the 
                                          session is configured as 
                                          source rspan session then data 
                                          mirrored for the source 
                                          entities will be forwarded on 
                                          this vlan if the session is 
                                          configured as destination 
                                          rspan session then data 
                                          received on this vlan will be 
                                          forwarded to the destination 
                                          entities of this session
          
     Following are the configuration details for configurating Vlan 
     based mirroring:
         To configure vlans as source for a session
        - issMirrorCtrlExtnMirrType - is set to vlanBased
        - issMirrorCtrlExtnSrcVlanTable - should be used to configure 
                                          list of source vlans to be 
                                          mirrored in a session
          - issMirrorCtrlExtnSrcVlanId  - represents a source vlan. The 
                                          vlan to be mirrored should be 
                                          given here.
          - issMirrorCtrlExtnSrcVlanCfg - this object is used to 
                                          add/remove a vlan in the 
                                          source vlan list 
             Example
             To create a session 1 with source list as vlan 5,6 
             belonging to context 1 following sequence of configuration
             should be followed
             For table issMirrorCtrlExtnTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnMirrType = vlanBased
          
             For table issMirrorCtrlExtnSrcVlanTable
             issMirrorCtrlExtnSrcVlanContext = 1 as index
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnSrcVlanId  = 5 as index
             issMirrorCtrlExtnSrcVlanCfg = add
             issMirrorCtrlExtnSrcVlanContext = 1 as index
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnSrcVlanId  = 6 as index
             issMirrorCtrlExtnSrcVlanCfg = add
                       
Entries for this table can be configured only when issMirrorStatus 
is set to enabled.
Configurations done through 'issMirrorCtrlTable' will change the 
following for the first session on this table:
     - Mirroring type will be changed to port-based
     - Mode and Source entities will be overwritten 
       with the values configured through 'issMirrorCtrlTable'
     - Destination entities will be overwritten 
       with the value configured through 'issMirrorToPort' object

issMirrorCtrlExtnEntry row .1.3.6.1.4.1.10876.101.1.81.3.6.1

An entry appears in this table for each session
in the system.

Indexes

issMirrorCtrlExtnSessionIndex

Column	Syntax	OID
issMirrorCtrlExtnSessionIndex The index of the mirroring session for which the configuration in this entry applies.	Integer32 Constraints: range: 1-20	.1.3.6.1.4.1.10876.101.1.81.3.6.1.1
issMirrorCtrlExtnMirrType This object tells the type of mirroring this session supports. This object needs to be set before doing any configuration for a mirroring session	Enumerationr/w Enumerated Values: 1 portBased 2 mac-flowBased 3 vlanBased 4 invalid 5 ip-flowBased	.1.3.6.1.4.1.10876.101.1.81.3.6.1.2
issMirrorCtrlExtnRSpanStatus This object indicates session is enabled or disabled for Remote monitoring. If set as 'source-rspan-vlanid' indicates that the session is enabled for Remote monitoring and the source entities for this session will be…	Enumerationr/w Enumerated Values: 1 sourceRSpanVlan 2 destinationRSpanVlan 3 disabled	.1.3.6.1.4.1.10876.101.1.81.3.6.1.3
issMirrorCtrlExtnRSpanVlanId Vlan Id used for Remote monitoring for this session. If issMirrorCtrlExtnRSpanStatus is set to disabled, then this object will have an invalid value (zero)	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.81.3.6.1.4
issMirrorCtrlExtnRSpanContext Specifies the Context Id to which the RSpan Vlan belongs. Value '0' mean this object is not considered for this mirroring session.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.81.3.6.1.5
issMirrorCtrlExtnStatus This object indicates the status of the entry. The entry can be made active only if issMirrorCtrlExtnMirrType is configured and source and destination entries for this sesion is also configured	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.81.3.6.1.6

A table to configure list of source entities for mirroring sessions

issMirrorCtrlExtnSrcEntry row .1.3.6.1.4.1.10876.101.1.81.3.7.1

An entry appears in this table for each mirroring session.

Indexes

issMirrorCtrlExtnSessionIndex issMirrorCtrlExtnSrcId

Column	Syntax	OID
issMirrorCtrlExtnSrcId Specifies the source id which participates in a mirroring session. For Port based mirroring this object can be port IfIndex. To mirror Tunnel and Trunk ports the same Id can be used for specifying Tunnel/Trunk Id. For …	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.3.7.1.1
issMirrorCtrlExtnSrcCfg This object is used to create/delete a source entry for a session.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.10876.101.1.81.3.7.1.2
issMirrorCtrlExtnSrcMode Provides control to set the mode of mirroring. It can be ingress, egress, both or disable.	Enumerationr/w Enumerated Values: 1 ingress 2 egress 3 both 4 disable	.1.3.6.1.4.1.10876.101.1.81.3.7.1.3

A table to configure list of vlan source entities for mirroring sessions

issMirrorCtrlExtnSrcVlanEntry row .1.3.6.1.4.1.10876.101.1.81.3.8.1

An entry appears in this table for each mirroring session.

Indexes

issMirrorCtrlExtnSessionIndex issMirrorCtrlExtnSrcVlanContext issMirrorCtrlExtnSrcVlanId

Column	Syntax	OID
issMirrorCtrlExtnSrcVlanContext Specifies the Context Id to which the source entity belongs, this is used in case of specifying vlan as source. Value '-1' mean this object is not considered for this mirroring session.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.1.81.3.8.1.1
issMirrorCtrlExtnSrcVlanId Specifies the Vlan id which participates in a mirroring session.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.10876.101.1.81.3.8.1.2
issMirrorCtrlExtnSrcVlanCfg This object is used to create/delete a vlan entry for a session.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.10876.101.1.81.3.8.1.3
issMirrorCtrlExtnSrcVlanMode Provides control to set the mode of mirroring. It can be ingerss,Egress or Both.	Enumerationr/w Enumerated Values: 1 ingress 2 egress 3 both	.1.3.6.1.4.1.10876.101.1.81.3.8.1.4

A table to configure list of destination entities

issMirrorCtrlExtnDestinationEntry row .1.3.6.1.4.1.10876.101.1.81.3.9.1

An entry appears in this table for each destination entity
in a mirroring session.

Indexes

issMirrorCtrlExtnSessionIndex issMirrorCtrlExtnDestination

Column	Syntax	OID
issMirrorCtrlExtnDestination Specifies the destination port id which participates in a mirroring session.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.3.9.1.1
issMirrorCtrlExtnDestCfg This object is used to create/delete a destination entry for a session.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.10876.101.1.81.3.9.1.2

A table to configure IP authorized managers in the system.

issIpAuthMgrEntry row .1.3.6.1.4.1.10876.101.1.81.7.1.1

Each entry in this table represents rules for particular
IP authorized manager.

Indexes

issIpAuthMgrIpAddr issIpAuthMgrIpMask

Column	Syntax	OID
issIpAuthMgrIpAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.81.7.1.1.1
issIpAuthMgrIpMask Specifies the IP address mask to be applied on issIpAuthMgrIpAddr. Value 0.0.0.0 indicates mask for 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.81.7.1.1.2
issIpAuthMgrPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of…	PortListr/w	.1.3.6.1.4.1.10876.101.1.81.7.1.1.3
issIpAuthMgrVlanList Specifies the Vlan's in which the IP authorized manager can reside. By default the manager is allowed to reside in any vlan. If a set of vlans are configured in the 'VlanList', the manager can reside onl…	OctetStringr/w	.1.3.6.1.4.1.10876.101.1.81.7.1.1.4
issIpAuthMgrOOBPort Specifies whether the authorized manager can access the switch through OOB Port By default the manager is denied access to reside on OOB Interface	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.81.7.1.1.5
issIpAuthMgrAllowedServices Specifies the allowed services through which the authorized manager can access the switch. This object takes bit mask values. The services represented by each bit position is as given below: With bi…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.81.7.1.1.6
issIpAuthMgrRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.81.7.1.1.7

A table to L4 Switching rules in the system.

issL4SwitchingFilterEntry row .1.3.6.1.4.1.10876.101.1.81.9.1.1

Each entry in this table is a L4 Switching rule.
Index to the table is L4 filter number.

Indexes

issL4SwitchingFilterNo

Column	Syntax	OID
issL4SwitchingFilterNo L4 Switching Filter rule number.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.9.1.1.1
issL4SwitchingProtocol The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it will not be checked to decide the action.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.81.9.1.1.2
issL4SwitchingPortNo The Layer 4 port no. Please note these ports are the TCP / UDP ports.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.81.9.1.1.3
issL4SwitchingCopyToPort This object is Port to which the packet would be switched	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.1.81.9.1.1.4
issL4SwitchingFilterStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.81.9.1.1.5

A table for triggering Graceful shutdown and Start

issModuleEntry row .1.3.6.1.4.1.10876.101.1.81.12.1.1

Each entry in this table corresponding to one protocol

Indexes

issModuleId

Column	Syntax	OID
issModuleId This object indicates the ID of the protocol. Following IDs are supported. 1. OSPF 2. OSPFV3 3. BGP 4. ISIS 5. RSVPTE 6. LDP	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.1.81.12.1.1.1
issModuleSystemControl This object shuts and starts the process	Enumerationr/w Enumerated Values: 0 idle 1 shutdown 2 start	.1.3.6.1.4.1.10876.101.1.81.12.1.1.2

Table containing the Fan information.

issSwitchFanEntry row .1.3.6.1.4.1.10876.101.1.81.13.1.1

Indicates information related to fan status of
the switch.

Indexes

issSwitchFanIndex

Column	Syntax	OID
issSwitchFanIndex Indicates the fan number in the switch	Integer32 Constraints: range: 1-5	.1.3.6.1.4.1.10876.101.1.81.13.1.1.1
issSwitchFanStatus Indicates the fan status of the switch.	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.10876.101.1.81.13.1.1.2

A table to configure User-Defined filter rules in the system.

issUDFilterEntry row .1.3.6.1.4.1.10876.101.1.81.18.1.1

Each entry in this table is a User-Defined filter rule.
Index to the table is User-Defined filter number.

Indexes

issUDFilterNo

Column	Syntax	OID
issUDFilterNo User-Defined Filter rule number. This object is deprecated and the corresponding functionality is met with issUDFilter objects in fsissext.mib.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.10876.101.1.81.18.1.1.1
issUDFilterPriority The priority of the UDF filter can be used to decide which filter rule is applicable when the packet matches with more than one filter rules. Higher value of 'filter priority' implies a higher priority.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.10876.101.1.81.18.1.1.2
issUDFilterPktType The packet header type to be filtered by User-Defined Filter.	Enumerationr/w Enumerated Values: 0 mac 1 tcp 2 udp 5 ipv4	.1.3.6.1.4.1.10876.101.1.81.18.1.1.3
issUDFilterDstMacAddr Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont care condition ie) any Dst Mac Address. This object is valid only if the 'issUDFilterPktType' …	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.10876.101.1.81.18.1.1.4
issUDFilterSrcMacAddr Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care condition ie) any Src Mac address. This object is valid only if the 'issUDFilterPktType' is 'MAC'.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.10876.101.1.81.18.1.1.5
issUDFilterProtocol The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it will not be checked to decide the action. This object is vali…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.10876.101.1.81.18.1.1.6
issUDFilterDstIpAddr Destination IP address to be matched with the packet. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.81.18.1.1.7
issUDFilterSrcIpAddr Source IP address to be matched with the packet. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.81.18.1.1.8
issUDFilterDstIpAddrMask The IP subnet mask for Destination IP address. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.81.18.1.1.9
issUDFilterSrcIpAddrMask The IP subnet mask for Source IP address. This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.81.18.1.1.10
issUDFilterMinDstProtPort The minimum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.81.18.1.1.11
issUDFilterMaxDstProtPort The maximum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.81.18.1.1.12
issUDFilterMinSrcProtPort The minimum port in the source port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.81.18.1.1.13
issUDFilterMaxSrcProtPort The maximum port in the source port range. Please note these ports are the TCP / UDP ports. This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.81.18.1.1.14
issUDFilterInPortList Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the incoming port list is '0', the filter rule is applicable for all the incoming ports. By default inport li…	PortListr/w	.1.3.6.1.4.1.10876.101.1.81.18.1.1.15
issUDFilterOutPortList Specifies the complete set of ports over which if the packet goes out, this filter rule will be applicable. If the outgoing port list is '0',the filter rule is applicable for all the outgoing packets in all ports. The…	PortListr/w	.1.3.6.1.4.1.10876.101.1.81.18.1.1.16
issUDFilterAction Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be sent to the ports in 'out port list'. If the out port list is '0', the port over which the packet …	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.10876.101.1.81.18.1.1.17
issUDFilterStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.81.18.1.1.18

A profile table to configure Explicit Congestion Notification (ECN) in the system.

ecnProfileEntry row .1.3.6.1.4.1.10876.101.1.81.19.1.1

Each entry in this table is a Explicit Congestion Notification (ECN) profile .
Index to the table is profile name.

Indexes

ecnProfileName

Column	Syntax	OID
ecnProfileName ECN Profile Name	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.10876.101.1.81.19.1.1.1
ecnProfileMinThreshold Packets are treated normally when average queue size below minimum threshold (bytes).	Unsigned32r/w Constraints: range: 1-13631072	.1.3.6.1.4.1.10876.101.1.81.19.1.1.2
ecnProfileMaxThreshold Packets are marked congestion experienced when average queue size above maximum threshold (bytes).	Unsigned32r/w Constraints: range: 1-13631280	.1.3.6.1.4.1.10876.101.1.81.19.1.1.3
ecnProfileProbability The proportion of ECN marking varies linear with average queue size when average queue size between minimum and maximum thresholds.	Unsigned32r/w Constraints: range: 0-100	.1.3.6.1.4.1.10876.101.1.81.19.1.1.4
ecnProfilePortList Specifies the inteface lists to be applied ECN profile. e.g. 8040... : Port 1 and 6 ...	PortListr/w	.1.3.6.1.4.1.10876.101.1.81.19.1.1.5
ecnProfileRowStatus This object is used to create and delete rows in the ecnProfileTable.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.81.19.1.1.6