SLE-BRIDGE-MIB Table View

Bridge Port Table

sleBridgePortEntry row .1.3.6.1.4.1.6296.101.3.2.1.1

Bridge Port Entry
key: sleBridgePortIndex

Indexes

sleBridgePortIndex

Column	Syntax	OID
sleBridgePortIndex Same as ifIndex (for all ifTable entries), additionally aggregation group index values available.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.1
sleBridgePortIfIndex Bridge Interface Index.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.2.1.1.2
sleBridgePortPVid The PVID of port. Taken if no other rule given for VLAN association. If aggregated: only for group.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.2.1.1.3
sleBridgePortMaxHosts The maximum number of hosts allowed. Aggregation group available. Value 0 is allowed. Default value is -1: it means unlimited.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.6296.101.3.2.1.1.4
sleBridgePortCurrentHosts The number hosts which is allowed to be used. Aggregation group available.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.5
sleBridgePortMaxLearnPerUnit Limit maximum number of MAC addresses learning newly per unit time(one second) on a port. (0: nothing learned, -l: unlimited.)	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.6296.101.3.2.1.1.6
sleBridgePortMACFilterPermission The default permission for mac filtering. Valid only for physical ports, use values from MFDB Table.	Enumeration Enumerated Values: 0 deny 1 permit	.1.3.6.1.4.1.6296.101.3.2.1.1.7
sleBridgePortIngMirrorStatus Mirroring on ingress packets. Valid only for physical ports.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.8
sleBridgePortEgMirrorStatus Mirroring on egress packets. Valid only for physical ports.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.9
sleBridgePortBcastThreshold Broadcast packet rate limit(unit: packets/s), Valid only for physical ports. Default value is 0: it means BCSC clear-state. Value Range: 0-262142(TX/FX),0-2097150(GBIC).	Integer32 Constraints: range: 0-2097150	.1.3.6.1.4.1.6296.101.3.2.1.1.10
sleBridgePortMcastThreshold Multicast packet rate limit.(unit: packets/s), Valid only for physical ports. Default value is 0: it means BCSC clear-state. Value Range: 0-262142(TX/FX),0-2097150(GBIC).	Integer32 Constraints: range: 0-2097150	.1.3.6.1.4.1.6296.101.3.2.1.1.11
sleBridgePortDlfThreshold DLF packet rate limit(unit: packets/s), Valid only for physical ports. Default value is 0: it means BCSC clear-state. Value Range: 0-262142(TX/FX),0-2097150(GBIC).	Integer32 Constraints: range: 0-2097150	.1.3.6.1.4.1.6296.101.3.2.1.1.12
sleBridgePortQinQStatus QinQ Status of the port. Valid only for physical ports.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.13
sleBridgePortAdminLinktype The administrative link-type of port on the xSTP.	Enumeration Enumerated Values: 0 shared 1 pointTopoint 2 automatic	.1.3.6.1.4.1.6296.101.3.2.1.1.14
sleBridgePortAdminEdgemode The administrative edgemode of port on the xSTP.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.15
sleBridgePortOperLinktype The link-type of the port on the xSTP.	Enumeration Enumerated Values: 0 shared 1 pointTopoint	.1.3.6.1.4.1.6296.101.3.2.1.1.16
sleBridgePortOperEdgemode The edge-mode of the port on the xSTP.	Enumeration Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.6296.101.3.2.1.1.17
sleBridgePortStpBpduFilter The stp bpdu-filter of the port on the xSTP. Default value is 0.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.18
sleBridgePortPvlanIsolatedStatus Isolated status of this port. Default value is disable(0).	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.19
sleBridgePortPvlanPromPorts Portlist for promiscuous ports of this port. The OctetString is a list of pairs of octets each identify an sheBridgePortIndex. The least significant byte is the second octet.	OctetString	.1.3.6.1.4.1.6296.101.3.2.1.1.20
sleBridgePortDhcpFilterServer DHCP filter server status 0: disabled 1: enabled	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.21
sleBridgePortLoopDetectStatus The adminStatus of loop-detect per ports.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.2.1.1.22
sleBridgePortLoopDetectBlock The adminBlock mode of loop-detect per ports. Indicate whether block port or not.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.2.1.1.23
sleBridgePortLoopDetectPeriod The sending period of detection packet.	Integer32 Constraints: range: 1-60	.1.3.6.1.4.1.6296.101.3.2.1.1.24
sleBridgePortLoopDetectTimer The Blocked list expire timer.	Integer32 Constraints: range: 0-86400	.1.3.6.1.4.1.6296.101.3.2.1.1.25
sleBridgePortLoopDetectBlockStatus The operStauts of loop-detect per ports.	Enumeration Enumerated Values: 1 block 2 unblock	.1.3.6.1.4.1.6296.101.3.2.1.1.26
sleBridgePortNetBIOSFilter The netBios filter status per ports	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.27
sleBridgePortPushInnertag The ingress port that push inner-tag	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.28
sleBridgePortPopInnertag The egress port that pop inner-tag	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.29
sleBridgePortInnertag The inner-tag value to push for incoming untagged packet	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.6296.101.3.2.1.1.30
sleBridgePortPriority The port priority value for incoming untagged packet	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.6296.101.3.2.1.1.31
sleBridgePortInner2outerPri Use inner-tag??s priority as outer-tag??s priority.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.32
sleBridgePortInner2outerVid Use inner-tag??s vlan-id as outer-tag??s vlan-id.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.33
sleBridgePortLinkUpCnt The times of link-up event	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.34
sleBridgePortLinkDownCnt The times of link-down event	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.35
sleBridgePortLinkUpTime The elapsed time after link is up.	1 secSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.6296.101.3.2.1.1.36
sleBridgePortElapsedTimeAfterClearStats The elapsed time after clearing statistics.	1 secSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.6296.101.3.2.1.1.37
sleBridgePortMACLearningStatus If enable, SLF packet is forwarded with mac-learning. Otherwise, SLF packet is forwarded without mac-learning.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.2.1.1.38
sleBridgePortPortBridgeStatus Port Bridge Feature for transmitting the packet out on the same port of which is received.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.2.1.1.39
sleBridgePortUnknownMcastBlock Unknown multicast block setting for a port.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.2.1.1.40
sleBridgePortDescription The port description.	OctetStringr/w Constraints: range: 1-128	.1.3.6.1.4.1.6296.101.3.2.1.1.41
sleBridgePortHoldTime The hold-time	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.42
sleBridgePortMacAntiSpoofing The mac anti-spoofing per port.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6296.101.3.2.1.1.43
sleBridgePortSwitchType Interface type.	Enumeration Enumerated Values: 1 special 2 inner 3 vlan 4 eth 5 portChannel 6 tunnel 255 unknown	.1.3.6.1.4.1.6296.101.3.2.1.1.44
sleBridgePortSwitchState The interface mode to switched port or routed port.	Enumeration Enumerated Values: 1 switchedPort 2 routedPort	.1.3.6.1.4.1.6296.101.3.2.1.1.45
sleBridgePortSwitchMode The switching mode of L2 interface.	Enumeration Enumerated Values: 1 access 2 hybrid 3 trunk 4 ce 5 cn 6 pn 7 pe 8 cnp 9 vip 10 pip 11 cbp 255 invalid	.1.3.6.1.4.1.6296.101.3.2.1.1.46
sleBridgePortSwitchSubMode The switching sub mode of L2 interface.	Enumeration Enumerated Values: 1 access 2 hybrid 3 trunk 4 ce 5 cn 6 pn 7 pe 8 cnp 9 vip 10 pip 11 cbp 255 invalid	.1.3.6.1.4.1.6296.101.3.2.1.1.47
sleBridgePortSwitchDefaultVlan The default VLAN of L2 interface.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.2.1.1.48
sleBridgePortSwitchIngressFilter Set the ingress filtering for the received frames.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.2.1.1.49
sleBridgePortSwitchAccFrameType Set the Layer 2 interface acceptable frame types. This processing occurs after VLAN classification. vlan-tagged Accept only classified frames which belong to the port's member set. Hybridge interface on…	Bits Enumerated Values: 0 allType 1 tagged 2 untagged	.1.3.6.1.4.1.6296.101.3.2.1.1.50
sleBridgePortSwitchNativeVid The native VLAN is used for classifying the incoming untagged packets.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.2.1.1.51
sleBridgePortSwitchAllowedVlan Both tagged and untagged frames will be classified over interfaces.	OctetString	.1.3.6.1.4.1.6296.101.3.2.1.1.52
sleBridgePortSwitchAllowedVlanEtag egress Port string	OctetString	.1.3.6.1.4.1.6296.101.3.2.1.1.53
sleBridgePortSwitchChannelType Indicate whether port is aggregator or aggregated(member).	Enumeration Enumerated Values: 0 none 1 aggregator 2 aggregated	.1.3.6.1.4.1.6296.101.3.2.1.1.54
sleBridgePortSwitchStaticChannelGroup Static channel group name	OctetString	.1.3.6.1.4.1.6296.101.3.2.1.1.55
sleBridgePortSwitchChannelLoadbalance Channel group hash method.	Enumeration Enumerated Values: 1 dstMac 2 srcMac 3 srcDstMac 4 srcIp 5 dstIp 6 srcDstIp 7 srcPort 8 dstPort 9 srcDstPort	.1.3.6.1.4.1.6296.101.3.2.1.1.56
sleBridgePortSwitchAggrType aggregate type	Enumeration Enumerated Values: 0 noneAggregated 1 aggregatedStatic 2 aggregatedLacp 3 aggregatorStatic 4 aggregatorLacp	.1.3.6.1.4.1.6296.101.3.2.1.1.57
sleBridgePortSwitchAggrId aggregate ID	Integer32 Constraints: range: 0-12	.1.3.6.1.4.1.6296.101.3.2.1.1.58
sleBridgePortSwitchAggrMode aggregate mode	Enumeration Enumerated Values: 0 noneAggregated 1 aggregatedActive 2 aggregatedPassive	.1.3.6.1.4.1.6296.101.3.2.1.1.59
sleBridgePortLoopDetectPeriodMs The sending period of detection packet. (Unit: milliseconds)	Integer32 Constraints: range: 1-60	.1.3.6.1.4.1.6296.101.3.2.1.1.91
sleBridgePortLoopDetectAdminCount The looping Admin count of LoopDetect	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.2.1.1.92
sleBridgePortLoopDetectOperCount The looping oper count of LoopDetect compared with adminCount	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.2.1.1.93
sleBridgePortLoopDetectDetectedCount The looping accumulated detected count of LoopDetect	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.2.1.1.94
sleBridgePortLoopDetectVlan The loop detect vlan. (0: Not Set)	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.6296.101.3.2.1.1.95
sleBridgePortMaxNewHosts The maximum number of New hosts allowed. Aggregation group available. Default value is 0: it means unlimited.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.96
sleBridgePortStpStatus STP status per interface.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.97
sleBridgePortStpBpduGuard The Spanning-tree bpduguard state	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.98
sleBridgePortOuterTpid The Ethertype for outer-tag	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.6296.101.3.2.1.1.99
sleBridgePortMirrorMonitor The Mirror monitor status	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.100
sleBridgePortBandwidth The bandwidth value for interface.	OctetString	.1.3.6.1.4.1.6296.101.3.2.1.1.101
sleBridgePortAlias The alias name for interface.	OctetString	.1.3.6.1.4.1.6296.101.3.2.1.1.102
sleBridgePortMulticast The interface supports multicast.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.2.1.1.103
sleBridgePortFloodBlock Packet flooding discarding.	Bits Enumerated Values: 0 bcast 1 dlf 2 mcast	.1.3.6.1.4.1.6296.101.3.2.1.1.104

sle vlan table

sleVlanEntry row .1.3.6.1.4.1.6296.101.3.3.1.1

key: sleVlanIndex

Indexes

sleVlanIndex

Column	Syntax	OID
sleVlanIndex A vlan-identifier.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.3.1.1.1
sleVlanIfIndex Same as ifIndex (for appropriated ifTable entries).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.3.1.1.2
sleVlanName A descriptional name for that vlan.	OctetString	.1.3.6.1.4.1.6296.101.3.3.1.1.3
sleVlanStatus static, in future gvrp	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.6296.101.3.3.1.1.4
sleVlanEgressPorts Portlist for all member of this VLAN, they will send tagged or untagged frames. The octet string is a list of pairs of octets each identify an sleBridgePortIndex. The least significant byte is the second octet.	OctetString	.1.3.6.1.4.1.6296.101.3.3.1.1.5
sleVlanUnTaggedPorts Portlist for members of this Vlan they will send only untagged frames. The octet string is a list of pairs of octets each identify an sleBridgePortIndex. The least significant byte is the second octet.	OctetString	.1.3.6.1.4.1.6296.101.3.3.1.1.6
sleVlanCreationTime Only useful in case of gvrp.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.3.1.1.7
sleVlanAgeingTime The ageing time per vlan	Integer32 Constraints: range: -1-0 range: 10-21474830	.1.3.6.1.4.1.6296.101.3.3.1.1.8
sleVlanTagTxCounter The VLAN tag tx counter.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.6296.101.3.3.1.1.9
sleVlanDescription createVlan: (sleVlanControlIndex) sleVlanControlName sleVlanControlMulticastPermision	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.6296.101.3.3.1.1.10
sleVlanElineEnable Indicate whether E-line service enable or not	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.3.1.1.11
sleVlanOperStatus The Vlan operation status.	Enumeration Enumerated Values: 0 invalid 1 inactive 2 active	.1.3.6.1.4.1.6296.101.3.3.1.1.12
sleVlanMtu The Vlan MTU.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.3.1.1.13
sleVlanType The Vlan service either customer or service.	Enumeration Enumerated Values: 1 customer 2 service	.1.3.6.1.4.1.6296.101.3.3.1.1.14

sle vlan table

sleServiceVlanEntry row .1.3.6.1.4.1.6296.101.3.3.4.1

key: sleVlanIndex

Indexes

sleVlanIndex

Column	Syntax	OID
sleServiceVlanIndex A vlan-identifier.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.3.4.1.1
sleServiceVlanName A descriptional name for that vlan.	OctetString	.1.3.6.1.4.1.6296.101.3.3.4.1.2
sleServiceVlanDescription createVlan: (sleVlanControlIndex) sleVlanControlName sleVlanControlMulticastPermision	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.6296.101.3.3.4.1.3
sleServiceVlanOperStatus The Vlan operation status.	Enumeration Enumerated Values: 0 invalid 1 inactive 2 active	.1.3.6.1.4.1.6296.101.3.3.4.1.4
sleServiceVlanMtu The Vlan MTU.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.3.4.1.5
sleServiceVlanStatus static, in future gvrp	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.6296.101.3.3.4.1.6
sleServiceVlanType The Vlan service either customer or service.	Enumeration Enumerated Values: 1 customer 2 service	.1.3.6.1.4.1.6296.101.3.3.4.1.7
sleServiceVlanSeviceType The Vlan service type.	Enumerationr/w Enumerated Values: 1 pointToPoint 2 multipointToMultipoint 3 rootedToMultipoint	.1.3.6.1.4.1.6296.101.3.3.4.1.8

vlan map table.

sleVlanMapEntry row .1.3.6.1.4.1.6296.101.3.4.1.1

key: sleVlanIndex

Indexes

sleVlanIndex

Column	Syntax	OID
sleVlanMapFid Index of the used Filtering Table entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.4.1.1.1
sleVlanMapStpId Index of the used STP instance.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.4.1.1.2
sleVlanMapErpDomainId Index of the used Erp Domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.4.1.1.3

STP instance table.

sleStpInstanceEntry row .1.3.6.1.4.1.6296.101.3.6.1.1

key: sleStpInstanceIndex

Indexes

sleStpInstanceIndex

Column	Syntax	OID
sleStpInstanceIndex The STP instance ID.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.6296.101.3.6.1.1.1
sleStpInstanceEnable The enabled/disabled status of the pvst.	Enumeration Enumerated Values: 0 enable 1 disable	.1.3.6.1.4.1.6296.101.3.6.1.1.2
sleStpInstancePriority The bridge priority.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.6.1.1.3
sleStpInstanceRootBridgeId The STP designated root bridge identifier in a specific instance. Size: 8.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.6296.101.3.6.1.1.4
sleStpInstanceRootPathcost The STP root path cost in a specific instance.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.6.1.1.5
sleStpInstanceDesignatedBridgeId TThe STP designated bridge identifier.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.6296.101.3.6.1.1.6
sleStpInstanceDesignatedPortId The STP designated port identifier.	Integer32 Constraints: range: 0-256	.1.3.6.1.4.1.6296.101.3.6.1.1.7
sleStpInstanceRootPortId The port number of the port which offers the lowest cost path from the this STP instance of this bridge to the root bridge.	Integer32 Constraints: range: 0-256	.1.3.6.1.4.1.6296.101.3.6.1.1.8
sleStpInstanceFwdDelay The current forward delay of the STP Instance.	Integer32 Constraints: range: 4-30	.1.3.6.1.4.1.6296.101.3.6.1.1.9
sleStpInstanceHelloTime The current hello time of the STP Instance.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.6296.101.3.6.1.1.10
sleStpInstanceMaxAge The current max age of the STP Instance.	Integer32 Constraints: range: 4-60	.1.3.6.1.4.1.6296.101.3.6.1.1.11
sleStpInstanceRemainHops The current remain hops of the MSTI or pvst.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.6.1.1.12
sleStpInstanceBrFwdDelay The Setting forward delay of the STP Instance.	Integer32 Constraints: range: 4-30	.1.3.6.1.4.1.6296.101.3.6.1.1.13
sleStpInstanceBrHelloTime The current hello time of the STP Instance.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.6296.101.3.6.1.1.14
sleStpInstanceBrMaxAge The Setting max age of the STP Instance.	Integer32 Constraints: range: 4-60	.1.3.6.1.4.1.6296.101.3.6.1.1.15

STP instance port table

sleStpInstancePortEntry row .1.3.6.1.4.1.6296.101.3.7.1.1

key: sleStpInstanceIndex, sleStpInstancePortIndex

Indexes

sleStpInstanceIndex sleStpInstancePortIndex

Column	Syntax	OID
sleStpInstancePortIndex The Port ID.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.7.1.1.1
sleStpInstancePortPathcost The STP port path cost.	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.6296.101.3.7.1.1.2
sleStpInstancePortPriority The STP port priority.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.6296.101.3.7.1.1.3
sleStpInstancePortRole The current STP Role of the Port.	Enumeration Enumerated Values: 0 disable 1 designated 2 root 3 master 4 alternate 5 backup	.1.3.6.1.4.1.6296.101.3.7.1.1.4
sleStpInstancePortState The STP forwarding state of a specific port.	Enumeration Enumerated Values: 0 disabled 1 listening 2 learning 3 forwarding 4 blocking	.1.3.6.1.4.1.6296.101.3.7.1.1.5
sleStpInstancePortRootBridgeId The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.6296.101.3.7.1.1.6
sleStpInstancePortRootPathcost The path cost of the Designated Port of the segment connected to this port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.7.1.1.7
sleStpInstancePortDesignateBridgeId The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.6296.101.3.7.1.1.8
sleStpInstancePortDesignatePortId The Port Identifier of the port on the Designated Bridge for this port's segment.	Integer32 Constraints: range: 0-256	.1.3.6.1.4.1.6296.101.3.7.1.1.9
sleStpInstancePortRootGuardMode An indication of whether the RootGuard capability is enabled on this port or not. This configuration will be applied to the VLAN or MSTP instance in which this port exists. Whether the RootGuard capabilit…	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.7.1.1.10

subnet vlan table.

sleSubnetVlanEntry row .1.3.6.1.4.1.6296.101.3.8.1.1

key: sleSubnetVlanIp, sleSubnetVlanMask

Indexes

sleSubnetVlanIp sleSubnetVlanMask

Column	Syntax	OID
sleSubnetVlanIp Ip address of Subnet	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.6296.101.3.8.1.1.1
sleSubnetVlanMask Mask bit.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.6296.101.3.8.1.1.2
sleSubnetVlanVid Index of the VLAN.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.8.1.1.3

protocol vlan table.

sleProtocolVlanEntry row .1.3.6.1.4.1.6296.101.3.9.1.1

key: sleBridgePortIndex, sleProtocolVlanEtype

Indexes

sleBridgePortIndex sleProtocolVlanEtype

Column	Syntax	OID
sleProtocolVlanEtype Ethernet type	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.9.1.1.1
sleProtocolVlanVid Index of the VLAN.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.9.1.1.2

lag table.

sleLagEntry row .1.3.6.1.4.1.6296.101.3.10.1.1

key: sleLagIndex

Indexes

sleLagIndex

Column	Syntax	OID
sleLagIndex This value assigned to the aggregation ID.	Integer32 Constraints: range: 0-13	.1.3.6.1.4.1.6296.101.3.10.1.1.1
sleLagPortId Port ID of aggregation.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.10.1.1.2
sleLagDistMode This value assigned to the distributing mode of link aggregation.	Enumeration Enumerated Values: 0 none 1 srcmac 2 dstmac 3 srcdstmac 4 srcip 5 dstip 6 srcdstip 7 srcdstl4 80 label	.1.3.6.1.4.1.6296.101.3.10.1.1.3
sleLagPortMap The value assigned to the port list of the aggregation.	OctetString	.1.3.6.1.4.1.6296.101.3.10.1.1.4
sleLagMode The operation mode of link aggregation.	Enumeration Enumerated Values: 0 inactive 1 trunk 2 lacp	.1.3.6.1.4.1.6296.101.3.10.1.1.5
sleLagLeastActive Description.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.10.1.1.6

lag LACP table.

sleLagLacpEntry row .1.3.6.1.4.1.6296.101.3.11.1.1

key: sleLagLacpIndex

Indexes

sleLagLacpIndex

Column	Syntax	OID
sleLagLacpIndex Location of authentication.	Integer32 Constraints: range: 0-13	.1.3.6.1.4.1.6296.101.3.11.1.1.1
sleLagLacpActorAggregatorKey The kind of authentication.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.11.1.1.2
sleLagLacpActorSystemMAC The Actor??s System ID, encoded as a MAC address.	OctetStringr/w	.1.3.6.1.4.1.6296.101.3.11.1.1.3
sleLagLacpPartnerSystemMAC Enable or disable the corresponding authen method.	OctetString	.1.3.6.1.4.1.6296.101.3.11.1.1.4
sleLagLacpPartnerSystemPriority The primary priority of the corresponding authen method.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.11.1.1.5
sleLagLacpPartnerAggregatorKey	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.11.1.1.6

lag LACP port table.

sleLagLacpPortEntry row .1.3.6.1.4.1.6296.101.3.12.1.1

key: sleLagLacpPortIndex

Indexes

sleLagLacpPortIndex

Column	Syntax	OID
sleLagLacpPortIndex The IP address of the RADIUS server referred to in this table entry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.12.1.1.1
sleLagLacpPortActivity show lacp activity of port	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.12.1.1.2
sleLagLacpPortActorPriority The priority assigned to the port by Actor.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.3
sleLagLacpPortActorAggregatorId The aggregator index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.12.1.1.4
sleLagLacpPortActorAdminKey The administrable Key value assigned to the port by the Actor.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.5
sleLagLacpPortActorAdminState The Actor's administrable state variables for the port.	Bits Enumerated Values: 0 expired 1 defaulted 2 destributing 3 collecting 4 synchronization 5 aggregation 6 lacpTimeout 7 lacpActivity	.1.3.6.1.4.1.6296.101.3.12.1.1.6
sleLagLacpPortActorOperKey The operational Key value assigned to the port by the Actor.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.7
sleLagLacpPortActorOperState The Actor's operational state variables for the port.	Bits Enumerated Values: 0 expired 1 defaulted 2 destributing 3 collecting 4 synchronization 5 aggregation 6 lacpTmeout 7 lacpActivity	.1.3.6.1.4.1.6296.101.3.12.1.1.8
sleLagLacpPortPartnerAdminSystemMAC The Partner's Administrable System ID, encoded as a MAC address.	OctetString	.1.3.6.1.4.1.6296.101.3.12.1.1.9
sleLagLacpPortPartnerAdminSystemPriority The administrable priority assigned to the Partner System.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.10
sleLagLacpPortPartnerAdminKey The administrable Key value assigned to the port by the Partner.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.11
sleLagLacpPortPartnerAdminNum The administrable number value assigned to the port by the Partner.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.12.1.1.12
sleLagLacpPortPartnerAdminPriority The administrable priority assigned to this port by the Partner.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.13
sleLagLacpPortPartnerAdminState The administrable state assigned to this port by the Partner.	Bits Enumerated Values: 0 expired 1 defaulted 2 destributing 3 collecting 4 synchronization 5 aggregation 6 lacpTmeout 7 lacpActivity	.1.3.6.1.4.1.6296.101.3.12.1.1.14
sleLagLacpPortPartnerOperSystemMAC The Partner's operational System ID, encoded as a MAC address.	OctetString	.1.3.6.1.4.1.6296.101.3.12.1.1.15
sleLagLacpPortPartnerOperSystemPriority The operational priority assigned to the Partner System.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.16
sleLagLacpPortPartnerOperKey The operational Key value assigned to the port by the Partner.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.17
sleLagLacpPortPartnerOperNum The operational number value assigned to the port by the Partner.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.12.1.1.18
sleLagLacpPortPartnerOperPriority The operational priority assigned to this port by the Partner.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.12.1.1.19
sleLagLacpPortPartnerOperState The operational state assigned to this port by the Partner.	Bits Enumerated Values: 0 expired 1 defaulted 2 destributing 3 collecting 4 synchronization 5 aggregation 6 lacpTimeout 7 lacpActivity	.1.3.6.1.4.1.6296.101.3.12.1.1.20
sleLagLacpPortActorAdminAggregatorId Admin aggregator Id.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.12.1.1.21

The table of FDB entries.

sleFdbEntry row .1.3.6.1.4.1.6296.101.3.13.1.1

The table entry of FDB table.
key: sleFdbEntryFid, sleFdbEntryPort, sleFdbEntryMacAddress

Indexes

sleFdbEntryFid sleFdbEntryPort sleFdbEntryMacAddress

Column	Syntax	OID
sleFdbEntryFid FDB identify.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.13.1.1.1
sleFdbEntryPort The port number of the port on which a frame having a source address equal to the value of the corresponding instance of dasanFdbAddress has been seen.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.6296.101.3.13.1.1.2
sleFdbEntryMacAddress A unicast MAC address for which the device has forwarding or filtering information.	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.6296.101.3.13.1.1.3
sleFdbEntryVid VLAN ID.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.13.1.1.4
sleFdbEntryMode FDB Entry's mode. The status of this entry. The meanings of the values are: local(0) - the value of the corresponding instance of sleFdbMacAddress was own. static(1) - the value of the corr…	Enumeration Enumerated Values: 0 local 1 static 2 dynamic	.1.3.6.1.4.1.6296.101.3.13.1.1.5
sleFdbEntryPermission The permission of dasanFdbAddress. The meanings of the values are: deny(0) - the value of the corresponding instance of dasanFdbAddress will be dropped. permit(1) - the value of the correspondi…	Enumeration Enumerated Values: 0 deny 1 permit	.1.3.6.1.4.1.6296.101.3.13.1.1.6
sleFdbEntryElapsedTime Elapsed time after registered	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.13.1.1.7

The table of MFDB entries.

sleMfdbOldEntry row .1.3.6.1.4.1.6296.101.3.14.1.1

Information about a specific MAC address that
should be forwarding or dropping.
key: sleMfdbMacAddress

Indexes

sleMfdbMacAddress

Column	Syntax	OID
sleMfdbOldMacAddress A unicast MAC address for which the device has forwarding or filtering information.	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.6296.101.3.14.1.1.1
sleMfdbOldEntryPermission The permission of sleMFdbMacAddress. The meanings of the values are: deny(0) - the value of the corresponding instance of sleMfdbMacAddress will be dropped. permit(1) - the value of the corres…	Enumeration Enumerated Values: 0 deny 1 permit	.1.3.6.1.4.1.6296.101.3.14.1.1.2
sleMfdbOldVlanIndex vlan index	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.6296.101.3.14.1.1.3
sleMfdbOldPorts Port Map	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.6296.101.3.14.1.1.4

IGMP configuration table.

sleIgmpConfEntry row .1.3.6.1.4.1.6296.101.3.15.1.1

key: sleVlanIndex

Indexes

sleVlanIndex

Column	Syntax	OID
sleIgmpConfVlanIndex sleVlanIndex in sleVlanTable	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.6296.101.3.15.1.1.1
sleIgmpConfEnable If this flag is true, IGMP multicasting is enabled. (not supported)	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.15.1.1.2
sleIgmpConfMulticastFilter If this flag is true, mac address that is unregistered into IGMP table is filtered. (not supported)	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.15.1.1.3
sleIgmpConfOutmostVlan Configures outmost VLAN. (not supported)	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.15.1.1.4
sleIgmpConfSnoopEnable The IGMP snooping enable/disable flag	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.15.1.1.5
sleIgmpConfSnoopJoinDelay After join message is received, the time interval until be registered into multicast group. (not supported)	Integer32 Constraints: range: 0-1000	.1.3.6.1.4.1.6296.101.3.15.1.1.6
sleIgmpConfSnoopQueryDelay After query message is send, the time interval for response waiting.	Integer32 Constraints: range: 100-900	.1.3.6.1.4.1.6296.101.3.15.1.1.7
sleIgmpConfSnoopMrouter The index of interface connected with multicast router.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.15.1.1.8
sleIgmpConfSnoopFastLeave If this flag is true, immediately this entry is deleted, when leave message is received,	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.15.1.1.9
sleIgmpConfSnoopQuerier If this flag is true, perform IGMP snooping querier.	Enumeration Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.15.1.1.10

IGMP multicast table.

sleIgmpMcastEntry row .1.3.6.1.4.1.6296.101.3.16.1.1

key: sleVlanIndex, sleIgmpMcastIPAddress, sleIgmpMcastPortIndex

Indexes

sleVlanIndex sleIgmpMcastIPAddress sleIgmpMcastPortIndex

Column	Syntax	OID
sleIgmpMcastVlanIndex sleVlanIndex in sleVlanTable	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.16.1.1.1
sleIgmpMcastIPAddress The IP multicast group address for which this entry contains information.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.6296.101.3.16.1.1.2
sleIgmpMcastPortIndex Port index	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.6296.101.3.16.1.1.3
sleIgmpMcastType indicate either static- or dynamic- IP multicast group address	Enumeration Enumerated Values: 0 static 1 dynamic	.1.3.6.1.4.1.6296.101.3.16.1.1.4
sleIgmpMcastExpireTime Expiry time of this dynamic multicast table entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.16.1.1.5

Information table of stack master/slave devices.

sleStackDeviceEntry row .1.3.6.1.4.1.6296.101.3.17.1.1

Information table entry of stack master/slave devices.
key: sleStackDeviceMacAddress

Indexes

sleStackDeviceMacAddress

Column	Syntax	OID
sleStackDeviceMacAddress MAC address of stack device.	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.6296.101.3.17.1.1.1
sleStackDeviceNodeId Index stack device nodes.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.17.1.1.2
sleStackDeviceDescriptor Description of stack device.	OctetString Constraints: range: 0-256	.1.3.6.1.4.1.6296.101.3.17.1.1.3
sleStackDeviceMode Stack status of device.	Enumeration Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.6296.101.3.17.1.1.4
sleStackDeviceStatus Stack status of stack device.	Enumeration Enumerated Values: 0 inactive 1 active	.1.3.6.1.4.1.6296.101.3.17.1.1.5
sleStackDeviceType Device type of stack device.	OctetString Constraints: range: 0-16	.1.3.6.1.4.1.6296.101.3.17.1.1.6
sleStackDeviceHostName Hostname of stack device.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.6296.101.3.17.1.1.7
sleStackDevicePortNum Number of stack device's ports.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.6296.101.3.17.1.1.8

erp domain table.

sleErpDomainEntry row .1.3.6.1.4.1.6296.101.3.18.1.1

key: sleErpDomainIndex

Indexes

sleErpDomainIndex

Column	Syntax	OID
sleErpDomainIndex An index value that uniquely identifies an ERP domain.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.18.1.1.1
sleErpDomainName Domain name.	OctetString	.1.3.6.1.4.1.6296.101.3.18.1.1.2
sleErpDomainPrimaryPort Interface index that represents the primary port of the domain.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.18.1.1.3
sleErpDomainSecondaryPort Interface index that represents the secondary port of the domain.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.18.1.1.4
sleErpDomainBridgeRole Mode that the ERP domain may operate in.	Enumeration Enumerated Values: 0 normalNode 1 rmNode	.1.3.6.1.4.1.6296.101.3.18.1.1.5
sleErpDomainProtectionActivation Protection activation.	Enumeration Enumerated Values: 0 deactivated 1 activated	.1.3.6.1.4.1.6296.101.3.18.1.1.6
sleErpDomainOperatorRequest Operator Request.	Enumeration Enumerated Values: 0 clear 1 manualToSecondary	.1.3.6.1.4.1.6296.101.3.18.1.1.7
sleErpDomainWaitToRestoreTime Time in seconds taken to verify that ring integrity is restored.	Integer32 Constraints: range: 1-720	.1.3.6.1.4.1.6296.101.3.18.1.1.8
sleErpDomainTestPacketInterval Time in mili seconds between consecutive transmissions of test packages.	Integer32 Constraints: range: 10-500	.1.3.6.1.4.1.6296.101.3.18.1.1.9
sleErpDomainLearningDisabledTime Time in mili seconds during which learning is disabled after a FDB flash.	Integer32 Constraints: range: 0-500	.1.3.6.1.4.1.6296.101.3.18.1.1.10
sleErpDomainNodeStatus Node status.	Enumeration Enumerated Values: 0 rmidle 1 primaryProtecting 2 protecting 3 idle 4 failedS 5 failedP 6 preForward 7 isolated 8 deactivated 9 backoff	.1.3.6.1.4.1.6296.101.3.18.1.1.11
sleErpDomainRingStatus Actual protection state on the ring.	Enumeration Enumerated Values: 0 normal 1 protecting 2 unknown	.1.3.6.1.4.1.6296.101.3.18.1.1.12
sleErpDomainLotp Loss of Test Packet alarm status. Only meaningful in RM node.	Enumeration Enumerated Values: 0 clear 1 raised	.1.3.6.1.4.1.6296.101.3.18.1.1.13
sleErpDomainULotp Unidirectional Detection of Loss of Test Packet alarm status. Only meaningful in RM node.	Enumeration Enumerated Values: 0 clear 1 raised	.1.3.6.1.4.1.6296.101.3.18.1.1.14
sleErpDomainMultipleRM Multiple Redundancy Manager alarm status. Only meaningful in RM node.	Enumeration Enumerated Values: 0 clear 1 raised	.1.3.6.1.4.1.6296.101.3.18.1.1.15
sleErpDomainRMNodeReacheablility RM Node reacheability alarm status. Only meaningful in normal node.	Enumeration Enumerated Values: 0 clear 1 raised	.1.3.6.1.4.1.6296.101.3.18.1.1.16
sleErpDomainHoldOffTime The hold off time.	Integer32 Constraints: range: 0-20000	.1.3.6.1.4.1.6296.101.3.18.1.1.17
sleErpDomainRingPriority The ring priority	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.6296.101.3.18.1.1.18

LLDP port table.

sleLldpPortEntry row .1.3.6.1.4.1.6296.101.3.19.1.1

key: sleLldpPortIndex

Indexes

sleLldpPortIndex

Column	Syntax	OID
sleLldpPortIndex LLDP port index	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.6296.101.3.19.1.1.1
sleLldpPortActivity sleLldpPortActivity	Boolean Type Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.19.1.1.2
sleLldpPortAdminStatus The administratively desired status of the local LLDP agent.	Enumerationr/w Enumerated Values: 1 txOnly 2 rxOnly 3 txAndRx 4 disabled	.1.3.6.1.4.1.6296.101.3.19.1.1.3
sleLldpPortNotificationEnable It controls, on a per port basis, whether or not notifications from the agent are enabled.	Booleanr/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.19.1.1.4
sleLldpPortTLVsTxEnable Bitmap that includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management.	Bitsr/w Enumerated Values: 0 portDesc 1 sysName 2 sysDesc 3 sysCap	.1.3.6.1.4.1.6296.101.3.19.1.1.5
sleLldpPortMgmtTxEnable It indicates that the port is either enable or not to transfer management address.	Boolean Type Values: 0 disable 1 enable	.1.3.6.1.4.1.6296.101.3.19.1.1.6
sleLldpPortMgmtAddress Management address to transfer on the port.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.6296.101.3.19.1.1.7
sleLldpPortTLVsTxNetworkPolciyProfile Assigned network-policy profile and specifies the network-policy TLV.	OctetString	.1.3.6.1.4.1.6296.101.3.19.1.1.8
sleLldpPortMgmtIPType Management IP address Type.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.19.1.1.9
sleLldpPortMgmtIPAddress Management IP address to transfer on the port.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.6296.101.3.19.1.1.10

LLDP remote table.

sleLldpRemoteEntry row .1.3.6.1.4.1.6296.101.3.20.1.1

key: sleLldpPortIndex, sleLldpRemIndex

Indexes

sleLldpPortIndex sleLldpRemIndex

Column	Syntax	OID
sleLldpRemIndex This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system.	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.6296.101.3.20.1.1.1
sleLldpRemTimeMark The sysUptime that this entry has been created or modified.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.20.1.1.2
sleLldpRemChassisIdSubtype The type of encoding used to identify the chassis associatedwith the remote system.	Enumeration Enumerated Values: 1 chassisComponent 2 interfaceAlias 3 portComponent 4 macAddress 5 networkAddress 6 interfaceName 7 local	.1.3.6.1.4.1.6296.101.3.20.1.1.3
sleLldpRemChassisId The type of encoding used to identify the chassis associatedwith the remote system.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.6296.101.3.20.1.1.4
sleLldpRemPortIdSubtype The type of port identifier encoding used in the associated'lldpRemPortId' object.	Enumerationr/w Enumerated Values: 1 interfaceAlias 2 portComponent 3 macAddress 4 networkAddress 5 interfaceName 6 agentCircuitId 7 local	.1.3.6.1.4.1.6296.101.3.20.1.1.5
sleLldpRemPortId The string value used to identify the port component associated with the remote system.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.6296.101.3.20.1.1.6
sleLldpRemPortDesc The string value used to identify the description of the given port associated with the remote system.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.6296.101.3.20.1.1.7
sleLldpRemSysName The string value used to identify the system name of the remote system.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.6296.101.3.20.1.1.8
sleLldpRemSysDesc The string value used to identify the system description of the remote system.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.6296.101.3.20.1.1.9
sleLldpRemSysCapSupported The bitmap value used to identify which system capabilities are supported on the remote system.	Bits Enumerated Values: 0 other 1 repeater 2 bridge 3 wlanAccessPoint 4 router 5 telephone 6 docsisCableDevice 7 stationOnly	.1.3.6.1.4.1.6296.101.3.20.1.1.10
sleLldpRemSysCapEnabled The bitmap value used to identify which system capabilities are enabled on the remote system.	Bits Enumerated Values: 0 other 1 repeater 2 bridge 3 wlanAccessPoint 4 router 5 telephone 6 docsisCableDevice 7 stationOnly	.1.3.6.1.4.1.6296.101.3.20.1.1.11

LLDP remote table.

sleLldpRemoteManAddrEntry row .1.3.6.1.4.1.6296.101.3.20.2.1

key: sleLldpPortIndex, sleLldpRemIndex

Indexes

sleLldpPortIndex sleLldpRemIndex sleLldpRemManAddrSubType sleLldpRemManAddr

Column	Syntax	OID
sleLldpRemManAddrSubType This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.6296.101.3.20.2.1.1
sleLldpRemManAddr The sysUptime that this entry has been created or modified.	OctetString	.1.3.6.1.4.1.6296.101.3.20.2.1.2
sleLldpRemManAddrIfSubType The type of encoding used to identify the chassis associatedwith the remote system.	SleLldpManAddrIfSubType Type Values: 1 unknown 2 ifIndex 3 systemPortNumber	.1.3.6.1.4.1.6296.101.3.20.2.1.3
sleLldpRemManAddrIfId The type of encoding used to identify the chassis associatedwith the remote system.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.20.2.1.4
sleLldpRemAddrOid The type of port identifier encoding used in the associated'lldpRemPortId' object.	ObjectIdentifier	.1.3.6.1.4.1.6296.101.3.20.2.1.5

LLDP statistics table.

sleLldpStatisticsEntry row .1.3.6.1.4.1.6296.101.3.21.1.1

key: sleLldpPortIndex

Indexes

sleLldpPortIndex

Column	Syntax	OID
sleLldpStatsTxPortFramesTotal The number of LLDP frames transmitted by this LLDP agent on the indicated port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.21.1.1.1
sleLldpStatsRxPortFramesDiscardedTotal The number of LLDP frames received by this LLDP agent on the indicated port, and then discarded for any reason.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.21.1.1.2
sleLldpStatsRxPortFramesErrors The number of invalid LLDP frames received by this LLDPagent on the indicated port, while this LLDP agent is enabled.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.21.1.1.3
sleLldpStatsRxPortFramesTotal The number of valid LLDP frames received by this LLDP agent on the indicated port, while this LLDP agent is enabled.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.21.1.1.4
sleLldpStatsRxPortTLVsDiscardedTotal The number of LLDP TLVs discarded for any reason by this LLDP agent on the indicated port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.21.1.1.5
sleLldpStatsRxPortTLVsUnrecognizedTotal The number of LLDP TLVs received on the given port that are not recognized by this LLDP agent on the indicated port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.21.1.1.6
sleLldpStatsRxPortAgeoutsTotal The counter that represents the number of age-outs that occurred on a given port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.21.1.1.7

bridge port security table.

sleBridgePSEntry row .1.3.6.1.4.1.6296.101.3.22.1.1

key: sleBridgePSIndex

Indexes

sleBridgePSIndex

Column	Syntax	OID
sleBridgePSIndex The index of logical port	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.6296.101.3.22.1.1.1
sleBridgePSStatus The status of port security	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.22.1.1.2
sleBridgePSMaxCount The max secure addresses The value of -1 is not used	Integer32 Constraints: range: -1--1 range: 1-16384	.1.3.6.1.4.1.6296.101.3.22.1.1.3
sleBridgePSCurrCount The current count of port security	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.22.1.1.4
sleBridgePSAgingType The aging type of port security	Enumeration Enumerated Values: 1 absolute 2 inactivity	.1.3.6.1.4.1.6296.101.3.22.1.1.5
sleBridgePSAgingTimer The aging time of port security The value of -1 and 0 means that aging time fixed to static and it will be not aging out But The case of 5924N, The value of -1 means that aging time fixed to static and it will be not ag…	secondInteger32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.6296.101.3.22.1.1.6
sleBridgePSAgingStatic The enable aging for configured secure addressess	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.22.1.1.7
sleBridgePSViolation The security violation mode of port security	Enumeration Enumerated Values: 1 shutdown 2 protect 3 restrict	.1.3.6.1.4.1.6296.101.3.22.1.1.8

bridge port security FDB table.

sleBridgePSFdbEntry row .1.3.6.1.4.1.6296.101.3.23.1.1

key: sleBridgePSFdbPort, sleBridgePSFdbVid, sleBridgePSFdbMacAddress

Indexes

sleBridgePSFdbPort sleBridgePSFdbVid sleBridgePSFdbMacAddress

Column	Syntax	OID
sleBridgePSFdbPort FDB mode configuration. 1: dynamic 2: static	Integer32 Constraints: range: 1-512	.1.3.6.1.4.1.6296.101.3.23.1.1.1
sleBridgePSFdbVid FDB vlan index	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.23.1.1.2
sleBridgePSFdbMacAddress FDB MAC address	OctetString Constraints: range: 0-6	.1.3.6.1.4.1.6296.101.3.23.1.1.3
sleBridgePSFdbMode FDB mode configuration. 1: dynamic 2: static	Enumeration Enumerated Values: 1 dynamic 2 static	.1.3.6.1.4.1.6296.101.3.23.1.1.4
sleBridgePSFdbElapsedTime FDB elapsed time	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6296.101.3.23.1.1.5

Description.

sleBridgeFGPortEntry row .1.3.6.1.4.1.6296.101.3.24.2.1.1

Description.

Indexes

sleBridgePortIndex sleBridgeFGPortType

Column	Syntax	OID
sleBridgeFGPortType Flood guard port type 1 : systemFloodGuard 2 : cpuFloodGuard 3 : macFloodGuard	Enumeration Enumerated Values: 1 systemFloodGuard 2 cpuFloodGuard 3 macFloodGuard	.1.3.6.1.4.1.6296.101.3.24.2.1.1.1
sleBridgeFGPortFrameType Flood guard frame type 0 : none 1 : multicast 2 : broadcast 3 : both	Enumeration Enumerated Values: 0 none 1 multicast 2 broadcast 3 both 4 arp 5 dhcp 6 dlf 7 all	.1.3.6.1.4.1.6296.101.3.24.2.1.1.2
sleBridgeFGPortFrame Flood guard frame	Integer32 Constraints: range: -1--1 range: 1-2147483647	.1.3.6.1.4.1.6296.101.3.24.2.1.1.3
sleBridgeFGPortBlocked Flood guard block status 1 : block 2 : unblock	Enumeration Enumerated Values: 1 block 2 unblock	.1.3.6.1.4.1.6296.101.3.24.2.1.1.4
sleBridgeFGPortTimer Flood guard timer	Integer32 Constraints: range: -1--1 range: 10-3600	.1.3.6.1.4.1.6296.101.3.24.2.1.1.5

bridge vlan translation table.

sleBridgeVTEntry row .1.3.6.1.4.1.6296.101.3.25.1.1

key: sleBridgeVTServiceId, sleBridgeVTSubscriberId

Indexes

sleBridgeVTServiceId sleBridgeVTSubscriberId

Column	Syntax	OID
sleBridgeVTServiceId Service Vlan Id	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.25.1.1.1
sleBridgeVTSubscriberId Subscriber Vlan Id	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.25.1.1.2

bridge vlan translation rule table.

sleBridgeVTRuleEntry row .1.3.6.1.4.1.6296.101.3.25.2.1

key: sleBridgeVTRuleMac, sleBridgeVTRuleVid

Indexes

sleBridgeVTRuleMac sleBridgeVTRuleVid

Column	Syntax	OID
sleBridgeVTRuleMac sleBridgeVTRuleMac, sleBridgeVTRuleVid	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.6296.101.3.25.2.1.1
sleBridgeVTRuleVid Original packet Vid	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.25.2.1.2
sleBridgeVTRuleRDirVid Output port	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.6296.101.3.25.2.1.3
sleBridgeVTRuleRDirPort Output Vid	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.25.2.1.4
sleBridgeVTRuleStatus Vlan Translation rule status	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.6296.101.3.25.2.1.5

bridge inbound vlan translation table.

sleBridgeInBoundVTEntry row .1.3.6.1.4.1.6296.101.3.25.5.1

key: sleBridgeInBoundVTPortIndex, sleBridgeInBoundVTVlanIndex

Indexes

sleBridgeInBoundVTPortIndex sleBridgeInBoundVTVlanIndex

Column	Syntax	OID
sleBridgeInBoundVTPortIndex Port Index.	Integer32 Constraints: range: 0-512	.1.3.6.1.4.1.6296.101.3.25.5.1.1
sleBridgeInBoundVTVlanIndex Vlan Index.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.6296.101.3.25.5.1.2
sleBridgeInBoundVTNewVid New VID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.25.5.1.3
sleBridgeInBoundVTOperStatus The operational status of InBound Vlan Translation.	Enumeration Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.6296.101.3.25.5.1.4

bridge outbound vlan translation table.

sleBridgeOutBoundVTEntry row .1.3.6.1.4.1.6296.101.3.25.8.1

key: sleBridgeOutBoundVTPortIndex, sleBridgeOutBoundVTVlanIndex

Indexes

sleBridgeOutBoundVTPortIndex sleBridgeOutBoundVTVlanIndex

Column	Syntax	OID
sleBridgeOutBoundVTPortIndex Port Index.	Integer32 Constraints: range: 0-512	.1.3.6.1.4.1.6296.101.3.25.8.1.1
sleBridgeOutBoundVTVlanIndex Vlan Index.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.6296.101.3.25.8.1.2
sleBridgeOutBoundVTNewVid New VID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.25.8.1.3
sleBridgeOutBoundVTOperStatus The operational status of InBound Vlan Translation.	Enumeration Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.6296.101.3.25.8.1.4

bridge GARP application port table.

sleBridgeGarpAppPortEntry row .1.3.6.1.4.1.6296.101.3.26.2.1.1

key: sleBridgeGarpAppPortIndex, sleBridgeGarpAppPortType

Indexes

sleBridgeGarpAppPortIndex sleBridgeGarpAppPortType

Column	Syntax	OID
sleBridgeGarpAppPortIndex Port index. Same as ifindex.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.6296.101.3.26.2.1.1.1
sleBridgeGarpAppPortType GARP Application Type. Supports GVRP, GMRP	Enumeration Enumerated Values: 1 gvrp 2 gmrp	.1.3.6.1.4.1.6296.101.3.26.2.1.1.2
sleBridgeGarpAppPortStatus GARP Application port status 1 : enable 2 : disable	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.26.2.1.1.3
sleBridgeGarpAppPortFailedRegistrations The current value of the Failed Registrations counter maintained for a GARP Attribute type.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.26.2.1.1.4
sleBridgeGarpAppPortLastPduOrigin MAC Address of the last pdu that caused a state change for a given GARP Attribute.	OctetString Constraints: range: 1-6	.1.3.6.1.4.1.6296.101.3.26.2.1.1.5
sleBridgeGarpAppPortRegistration GARP registration mode.	Enumeration Enumerated Values: 1 nomal 2 fixed 3 forbidden	.1.3.6.1.4.1.6296.101.3.26.2.1.1.6
sleBridgeGarpAppPortApplicant Applicant type 1: Transmissible PDU 2: Untransmissible PDU	Enumeration Enumerated Values: 1 participant 2 nonParticipant	.1.3.6.1.4.1.6296.101.3.26.2.1.1.7
sleBridgeGarpAppPortFwdAll GMRP forward all registered-groups.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6296.101.3.26.2.1.1.8
sleBridgeGarpAppPortTimerJoin GARP Application port timer join	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.26.2.1.1.9
sleBridgeGarpAppPortTimerLeave GARP Application port timer leave	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.26.2.1.1.10
sleBridgeGarpAppPortTimerLeaveAll GARP Application port timer leave all	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6296.101.3.26.2.1.1.11