SIAE-SFP-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
41

sfpSerialIdTable

table
.1.3.6.1.4.1.3373.1103.74.2 · 1 row entry · 20 columns
Open in standard view
Uses the siaemic variant from /opt/observium/mibs/siaemic.
Command help
Walk sfpSerialIdTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SIAE-SFP-MIB' -M '/opt/observium/mibs/siaemic:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SIAE-SFP-MIB::sfpSerialIdTable' 
Each SFP contains a 95+32 byte block of ID data fields.
This table contains the items found in this data block.
Fields in this data block is filled in by the SFP manufactor.
The table shows the contents of this data block without further
processing.
sfpSerialIdEntry row .1.3.6.1.4.1.3373.1103.74.2.1
SFP module record.
Indexes
Column Syntax OID
sfpModuleId
This index identifies a unique SFP module in the system
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.1
sfpSerialIdValid
When false the SFP data in this table is not valid. This
will be set to False if the SFP module is not installed or if
the EEPROM check code is wrong. The data in this table should
not be used unless this element is Tru…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.3373.1103.74.2.1.2
sfpVendorName
The SFP vendor name.
Located at I2C address 0xa0, bytes: 20 - 35
OctetString
Constraints:
range: 0-16
 .1.3.6.1.4.1.3373.1103.74.2.1.3
sfpVendorPartNumber
The SFP vendor part number.
Located at I2C address 0xa0, bytes: 40 - 55
OctetString
Constraints:
range: 0-16
 .1.3.6.1.4.1.3373.1103.74.2.1.4
sfpVendorRev
The SFP vendor's product revision number.
Located at I2C address 0xa0, bytes: 56 - 59
OctetString
Constraints:
range: 0-4
 .1.3.6.1.4.1.3373.1103.74.2.1.5
sfpVendorSN
The SFP vendor serial number.
Located at I2C address 0xa0, bytes: 68 - 83
OctetString
Constraints:
range: 0-16
 .1.3.6.1.4.1.3373.1103.74.2.1.6
sfpVendorDateCode
The SFP vendor date code.
Format: YYMMDDLL
- YY: year, 00 = 2000
- MM: month, 01 = January
- DD_ day, 01 to 31
- LL: vendor lot code, or blank.
Located at I2C address 0xa0, bytes: 84 -…
OctetString
Constraints:
range: 0-8
 .1.3.6.1.4.1.3373.1103.74.2.1.7
sfpDiagMonitorCode
This indicates which type of diagnostic monitoring is
implemented (if any) in the SFP.
-bit 7: = 0 legacy diagnostic implementations (should be 0)
-bit 6: = 1 digital diagnostic monitoring implemented (should be 1)
-bit…
Bits
Enumerated Values:
0sfpDMCtypeLegacy
1sfpDMCtypeImplemented
2sfpDMCtypeInternalCal
3sfpDMCtypeExternalCal
4sfpDMCtypeRxAvgPwr
5sfpDMCtypeAddrChngReqrd
 .1.3.6.1.4.1.3373.1103.74.2.1.8
sfpEnhancedOptionsCode
This indicates which optional enhanced features are
implemented (if any) in the SFP.
Located at I2C address 0xa0, byte: 93
Bits
Enumerated Values:
0sfpEOCalarmsImplemented
1sfpEOCSoftTxDisable
2sfpEOCSoftTxFault
3sfpEOCSoftRxLOS
4sfpEOCSoftRateSelect
 .1.3.6.1.4.1.3373.1103.74.2.1.9
sfpOptions
Implemented transceiver options:
-bit 5: = 1 RATE_SELECT implemented.
-bit 4: = 1 TX_DISABLE implemented
-bit 3: = 1 TX_FAULT implemented
-bit 2: = 1 LOS Implemented, inverted
-bit 1: = 1 LOS Implemented
Located at I2C …
Bits
Enumerated Values:
0sfpOPTRateSelect
1sfpOPTTxDisable
2sfpOPTTxFault
3sfpOPTInvertedLOS
4sfpOPTlos
 .1.3.6.1.4.1.3373.1103.74.2.1.10
sfpFibreChannelMedia
Fiber Channel transmission media.
Located at I2C address 0xa0, byte: 9
Bits
Enumerated Values:
0sfpMultiMode62u5
1sfpMultiMode50u0
2sfpSingleMode
3sfpTwistedAxialPair
4sfpShieldedTwistedPair
5sfpMiniatureCoax
6sfpVideoCoax
 .1.3.6.1.4.1.3373.1103.74.2.1.11
sfpCompliance
Electronic or optical interfaces that are supported by the
transceiver.
Located at I2C address 0xa0, bytes: 4,5 & 6
Bits
Enumerated Values:
0sfpSonetReachSpecifier1
1sfpSonetReachSpecifier2
2sfpSonetOC48LongReach
3sfpSonetOC48IntermediateReach
4sfpSonetOC48ShortReach
5sfpSonetOC12LongReach
6sfpSonetOC12IntermediateReach
7sfpSonetOC12ShortReach
8sfpSonetOC3LongReach
9sfpSonetOC3IntermediateReach
10sfpSonetOC3ShortReach
11sfp1000BaseT
12sfp1000BaseCX
13sfp1000BaseLX
14sfp1000baseSX
15sfpBasePX
16sfpBaseBX10
17sfp100BaseFX
18sfp100BaseLX
 .1.3.6.1.4.1.3373.1103.74.2.1.12
sfpWavelength
Nominal transmiter output wavelength at room temperature.
Units are in nm (nanometers).
Located at I2C address 0xa0, bytes: 60 & 61 (endianess: big)
nmSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.13
sfpNominalBitRate
Nominal bit rate (in megabit per second) supported from this
SFP module rouded to the nearest 100 megabits per second.
Located at I2C address 0xa0, byte: 12
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.14
sfpLinkLength9u
Link length (in meters) supported from this SFP module while
operating in compliance with the applicable standards using single
mode fiber. A value of zero means that the transceiver does not
support single mode fiber.
…
mSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.15
sfpLinkLength50u
Link length (in meters) supported from this SFP module while
operating in compliance with the applicable standards using
50 micron multi-mode fiber. A value of zero means that the
transceiver does not support 50 micron …
mSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.16
sfpLinkLength62u5
Link length (in meters) supported from this SFP module while
operating in compliance with the applicable standards using
62.5 micron multi-mode fiber. A value of zero means that the
transceiver does not support 62.5 mic…
mSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.17
sfpLinkLengthCopper
Link length (in meters) supported from this SFP module while
operating in compliance with the applicable standards using
copper cable. A value of zero means that the transceiver does
not support copper cable.
Located at…
mSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.2.1.18
sfpLabel
This is an ASCII string that identifies this SFP in the
system.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.3373.1103.74.2.1.19
sfpFailAlarm
SFP Module fail (module missing included)
SIAE-ALARM-MIBAlarmStatus
Type Values:
1cleared
2activeReportableStatus
3activeReportableWarning
4activeReportableMinor
5activeReportableMajor
6activeReportableCritical
 .1.3.6.1.4.1.3373.1103.74.2.1.20

sfpDiagnosticTable

table
.1.3.6.1.4.1.3373.1103.74.7 · 1 row entry · 12 columns
Open in standard view
Uses the siaemic variant from /opt/observium/mibs/siaemic.
Command help
Walk sfpDiagnosticTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SIAE-SFP-MIB' -M '/opt/observium/mibs/siaemic:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SIAE-SFP-MIB::sfpDiagnosticTable' 
Each SFP may contain a 256 byte block of diagnostic data
fields. This table contains the items found in this data block.
The data block is located at I2C address 0xa2.
sfpDiagnosticEntry row .1.3.6.1.4.1.3373.1103.74.7.1
This describes a row in the diagnostic table.
Indexes
Column Syntax OID
sfpDiagnosticValid
if False, then the SFP data in this table is not valid. This
will be set to False if the SFP module is not installed, or if
the I/O card that contains the SFP is not installed or if
the EEPROM check code is wrong. The d…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.3373.1103.74.7.1.1
sfpLOSPinOut
This contains the T/F state of the SFP LOS (output) pin. It is
True if the SFP has detected Loss-Of-Signal. located at I2c
address 0xa2, address: 110, mask 0x02
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.3373.1103.74.7.1.2
sfpTxFaultPinOut
This contains the T/F state of the SFP Tx Fault (output) pin.
It is True if the SFP has detected a Tx fault condition.
located at I2C address 0xa2, Byte 110, mask 0x04
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.3373.1103.74.7.1.3
sfpRateSelectPinIn
This contains the T/F state of the SFP RX Rate Select (input)
pin. This function is not implemented on Finisar SFPs. located
at I2C address 0xa2, Byte 110, mask 0x10
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.3373.1103.74.7.1.4
sfpTxDisablePinIn
This contains the T/F state of the SFP TX Disable (input) pin.
located at I2C address 0xa2, Byte 110, mask 0x80
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.3373.1103.74.7.1.5
sfpTemperature
This contains the internal temperature of the SFP in tehnth of
Celsius degrees. Range is from -128.0C to +128.0C, but is only
valid from -40.0C to +125.0C with an accuracy of +/- 3C.
Located at I2C address 0xa2, Bytes…
C/10Temperature
Type Constraints:
range: -2000..2000
 .1.3.6.1.4.1.3373.1103.74.7.1.6
sfpVoltage
This contains the internally measured SFP supply voltage
(Vcc). Units are in milliVolts (3210 = 3.21V). Range is 0 to
6.554V. Located at I2C address 0xa2, Bytes 98 & 99 (MSB, LSB)
milliVolts (mV)Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3373.1103.74.7.1.7
sfpTxBias
This contains the internally measured SFP TX laser bias
current. Units are in microAmps, and range from 0 to 131000uA
(131mA). Located at I2C address 0xa2, Bytes 100 & 101 (MSB, LSB)
microAmps (uA)Integer32
Constraints:
range: 0-131000
 .1.3.6.1.4.1.3373.1103.74.7.1.8
sfpTxPower
This contains the internally measured TX output power. Units
are in uW (micro Watts), and range from 0 to 6554uW (6.535mW).
This value is not valid if the transmitter is disabled. Located
at I2C address 0xa2, Bytes 102 …
microWatts (uW)Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3373.1103.74.7.1.9
sfpRxPower
This contains the internally measured RX optical power. Units
are in uW (micro Watts), and range from 0 to 6554uW (6.535mW).
Located at I2C address 0xa2, Bytes 104 & 105 (MSB, LSB)
microWatts (uW)Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3373.1103.74.7.1.10
sfpInternalAlarms
This contains the state of the SFP internal alarm register. A
bit is set for each alarm that is active. located at I2C
address 0xa2, Byte 112 & 113 (MSB, LSB) mask 0xffc0
Bits
Enumerated Values:
0sfpIntAlarmTempHigh
1sfpIntAlarmTempLow
2sfpIntAlarmVoltageHigh
3sfpIntAlarmVoltageLow
4sfpIntAlarmTxBiasHigh
5sfpIntAlarmTxBiasLow
6sfpIntAlarmTxPowerHigh
7sfpIntAlarmTxPowerLow
8sfpIntAlarmRxPowerHigh
9sfpIntAlarmRxPowerLow
 .1.3.6.1.4.1.3373.1103.74.7.1.11
sfpInternalWarnings
This contains the state of the SFP internal warning register.
A bit is set for each warning that is active. located at I2C
address 0xa2, Byte 116 & 117 (MSB, LSB) mask 0xffc0
Bits
Enumerated Values:
0sfpIntWarnTempHigh
1sfpIntWarnTempLow
2sfpIntWarnVoltageHigh
3sfpIntWarnVoltageLow
4sfpIntWarnTxBiasHigh
5sfpIntWarnTxBiasLow
6sfpIntWarnTxPowerHigh
7sfpIntWarnTxPowerLow
8sfpIntWarnRxPowerHigh
9sfpIntWarnRxPowerLow
 .1.3.6.1.4.1.3373.1103.74.7.1.12

sfpAlarmTable

table
.1.3.6.1.4.1.3373.1103.74.10 · 1 row entry · 9 columns
Open in standard view
Uses the siaemic variant from /opt/observium/mibs/siaemic.
Command help
Walk sfpAlarmTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SIAE-SFP-MIB' -M '/opt/observium/mibs/siaemic:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SIAE-SFP-MIB::sfpAlarmTable' 
This table contains the SFP alarm and warning threshold
values.
sfpAlarmEntry row .1.3.6.1.4.1.3373.1103.74.10.1
An entry into the Threshold table.
Indexes
Column Syntax OID
sfpPhysicalQuantity
Measured physical quantity.
Units of temperature are tenth of Celsius degrres,
units of Power supply voltage (Vcc) are microVolts,
units of Tx laser bias current are microAmps (uA),
units of Rx optical power are microWa…
PhysicalQuantity
Type Values:
1phyQtTemperature
2phyQtVoltage
3phyQtTxBias
4phyQtTxPower
5phyQtRxPower
 .1.3.6.1.4.1.3373.1103.74.10.1.1
sfpThresholdHighAlarm
A reading at or above this temperature will trigger a high
measured physical quantity alarm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.10.1.2
sfpThresholdHighWarning
A reading at or above this temperature will trigger a high
measured physical quantity warning.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.10.1.3
sfpThresholdLowAlarm
A reading at or above this temperature will trigger a low
measured physical quantity alarm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.10.1.4
sfpThresholdLowWarning
A reading at or above this temperature will trigger a low
measured physical quantity warning.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3373.1103.74.10.1.5
sfpHighAlarm
Measured physical quantity has crossed sfpThresholdHighAlarm.
SIAE-ALARM-MIBAlarmStatus
Type Values:
1cleared
2activeReportableStatus
3activeReportableWarning
4activeReportableMinor
5activeReportableMajor
6activeReportableCritical
 .1.3.6.1.4.1.3373.1103.74.10.1.6
sfpHighWarningAlarm
Measured physical quantity has crossed sfpThresholdHighWarning.
SIAE-ALARM-MIBAlarmStatus
Type Values:
1cleared
2activeReportableStatus
3activeReportableWarning
4activeReportableMinor
5activeReportableMajor
6activeReportableCritical
 .1.3.6.1.4.1.3373.1103.74.10.1.7
sfpLowAlarm
Measured physical quantity has crossed sfpThresholdLowAlarm.
SIAE-ALARM-MIBAlarmStatus
Type Values:
1cleared
2activeReportableStatus
3activeReportableWarning
4activeReportableMinor
5activeReportableMajor
6activeReportableCritical
 .1.3.6.1.4.1.3373.1103.74.10.1.8
sfpLowWarningAlarm
Measured physical quantity has crossed sfpThresholdLowWarning.
SIAE-ALARM-MIBAlarmStatus
Type Values:
1cleared
2activeReportableStatus
3activeReportableWarning
4activeReportableMinor
5activeReportableMajor
6activeReportableCritical
 .1.3.6.1.4.1.3373.1103.74.10.1.9