SCTE-HMS-HE-RF-SWITCH-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
17

heRFSwitchUnitTable

table
.1.3.6.1.4.1.5591.1.11.4.2.1.1.1 · 1 row entry · 9 columns
Open in standard view
Uses the scte variant from /opt/observium/mibs/scte.
Command help
Walk heRFSwitchUnitTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SCTE-HMS-HE-RF-SWITCH-MIB' -M '/opt/observium/mibs/scte:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SCTE-HMS-HE-RF-SWITCH-MIB::heRFSwitchUnitTable' 
A table containing information about RF Switch used
in an indoor environment.
heRFSwitchUnitEntry row .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1
List of information about each RF switch.
Indexes
Column Syntax OID
heRFSwitchMode
This controls and/or reports the switching mode. If
automatic(1), the RF switch will evaluate the RF
input status and make the decision to affect the switch state.
If set to manual(2), the RF switch will not affect…
Enumerationr/w .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.1
heRFSwitchControl
Sets the intended state of the RF Switch. The effect
of this control will depend on the value of heRFSwitchMode.
If heRFSwitchMode is set to automatic, the value this
control is set to will be the preferred setting. …
Enumerationr/w .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.2
heRFSwitchRevertEnable
This controls the use of revert switching.

If set to on, the switch will attempt to go back to the
preferred settings indicated by heRFSwitchControl if
heRFSwitchMode is set to automatic, and the inpu…
SCTE-HMS-HEADENDIDENT-MIBHeOnOffControlr/w
Enumerated Values:
1unknown
2port10M100MBASETX
3port100MBASEFXL
4port100MBASEFXS
5port1000MBASESX
6port1000MBASELX
7port1000MBASETX
8portGBIC
9port100MBASEFX
10port1000MBASEFX
11portSFP
12port10GBASESR
13port10GBASELR
14port10GBASEER
15port10GBASELX4
16port10GBASESW
17port10GBASELW
18port10GBASEEW
19port10GBASE
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.3
heRFSwitchState
Reports the state of the RF Switch. Not all enumerations
must be supported. For example, an A-B RF switch may
support only the pathA and pathB enumerations while a
cross-bar switch may support cross, bar, bothA or …
Enumeration
Enumerated Values:
1enabled
2disabled
3autonego
4unknown
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.4
heRFSwitchFailoverStatus
The integral status of both inputs.

A value is fault(2), if current switch state heRFSwitchState
is different than the preferred setting heRFSwitchControl,
otherwise, it is normal(1).
…
SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus
Type Values:
1normal
2fault
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.5
heRFSwitchBothInputStatus
The integral status of both inputs.

A value is fault(2), if both input levels are below
the nominal value; otherwise, it is normal(1).

This object must provide for the alarm management cap…
SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus
Enumerated Values:
1speed10Mb
2speed100Mb
3speed1000Mb
4autonego
5speed10Gb
6unknown
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.6
heRFSwitchHysteresis
Controls switch input hysteresis amount. The amount of hysteresis
used and the ability to change it is to be determined by
the vendor.
0.1 dBInteger32r/w
Enumerated Values:
1full
2half
3autonego
4unknown
Constraints:
range: -20-20
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.7
heRFSwitchWaitToRestoreTime
Controls hysteresis time in sec.

If in automatic switching mode and revert mode is enabled,
a switch back to the original side will be delayed for
the time specified by this object.
1 secSNMPv2-SMIInteger32r/w
Enumerated Values:
1speed10Mb
2speed100Mb
3speed1000Mb
4unknown
5speed10Gb
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.8
heRFSwitchSensorMode
Controls what source will be used for determining input
status:
A value of internal(1) causes the internal RF detection
circuitry to be used.
A value of external(2) will use heRFSwitchInputExternalControl
to …
Enumerationr/w
Enumerated Values:
1full
2half
3unknown
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.9

heRFSwitchInputTable

table
.1.3.6.1.4.1.5591.1.11.4.2.1.1.2 · 1 row entry · 6 columns
Open in standard view
Uses the scte variant from /opt/observium/mibs/scte.
Command help
Walk heRFSwitchInputTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SCTE-HMS-HE-RF-SWITCH-MIB' -M '/opt/observium/mibs/scte:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SCTE-HMS-HE-RF-SWITCH-MIB::heRFSwitchInputTable' 
A table containing information about each RF Switch 
input used in an indoor environment.
heRFSwitchInputEntry row .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1
List of information about each RF switch input.
Indexes
Column Syntax OID
heRFSwitchInputIndex
Index number corresponding to the RF Input.
SNMPv2-SMIUnsigned32
Enumerated Values:
1layer-2
2layer-3
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.1
heRFSwitchInputRFLevel
The measured RF input power for the RF switch.
0.1 dBmVSCTE-HMS-HEADENDIDENT-MIBHeTenthdBmV
Enumerated Values:
1access
2trunk
3dot1q-tunnel
4hybrid
5other
6uplink
7host
8promiscuous
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.2
heRFSwitchSetInputPowerThreshold
Input power switchover point for this input.
0.1 dBmVSCTE-HMS-HEADENDIDENT-MIBHeTenthdBmVr/w .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.3
heRFSwitchInputStatus
The integral status of the input.

A value is fault(2), if the input levels are not in
the nominal range; otherwise, it is normal(1).

This object must provide for the alarm management capab…
SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus
Type Values:
1normal
2fault
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.4
heRFSwitchInputDescription
A description of the switch input port. The description text is
to be determined by the equipment manufacturer. For example,
Input A or Side B.
OctetString
Enumerated Values:
0unknown
1copper
2fiber
Constraints:
range: 0-32
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.5
heRFSwitchInputExternalControl
This is an external control signal that indicates the status
of the associated input.

A value is fault(2), if the external control signal level is not in
the nominal range; otherwise, it is normal(1).
SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus
Type Values:
1normal
2fault
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.2.1.6

heRFSwitchOutputTable

table
.1.3.6.1.4.1.5591.1.11.4.2.1.1.3 · 1 row entry · 2 columns
Open in standard view
Uses the scte variant from /opt/observium/mibs/scte.
Command help
Walk heRFSwitchOutputTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SCTE-HMS-HE-RF-SWITCH-MIB' -M '/opt/observium/mibs/scte:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SCTE-HMS-HE-RF-SWITCH-MIB::heRFSwitchOutputTable' 
A table containing information about each RF Switch 
output used in an indoor environment.
heRFSwitchOutputEntry row .1.3.6.1.4.1.5591.1.11.4.2.1.1.3.1
List of information about each RF switch output.
Indexes
Column Syntax OID
heRFSwitchOutputIndex
Index number corresponding to the RF Output.
SNMPv2-SMIUnsigned32
Enumerated Values:
1primary
2secondary
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.3.1.1
heRFSwitchOutputDescription
A description of the switch output port. The description text
is to be determined by the equipment manufacturer. For example,
Output A or Seconday Output.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.5591.1.11.4.2.1.1.3.1.2