RUGGEDCOM-SERIAL-MIB Table View

A list of port entries. The number of entries might be
retreived as the value of object 'rs232Number' from RFC1659.

rcSerialPortEntry row .1.3.6.1.4.1.15004.4.6.1.1.1

Status and configuration parameters for a port.

Indexes

rcSerialPortNumber

Column	Syntax	OID
rcSerialPortNumber The physical Serial Port Number of the device for which this Entry contains configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.1.1.1.1
rcSerialPortIfIndex The value of ifIndex for the port. This value is same as 'rs232PortIndex' which is the index used for 'rs232PortTable' in RS-232-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.15004.4.6.1.1.1.2
rcSerialProtocol A Serial Protocol supported on the Serial Port represented by this entry.	RcSerProtocolr/w Type Values: 1 noProtocol 2 rawSock 3 modbusServer 4 modbusClient 5 itcsWIN 6 itcsTIN 7 microlok 8 dnp 9 dnpRawSock 10 mirrorBits 11 preemptRawSock 12 telnetComport	.1.3.6.1.4.1.15004.4.6.1.1.1.3
rcSerialPortType A Serial Port Type supported on the Serial Port represented by this entry.	RcSerPortTyper/w Type Values: 0 none 1 rs232 2 rs485 3 rs422 4 tpc 5 fiber	.1.3.6.1.4.1.15004.4.6.1.1.1.4
rcSerialForceHD Enables forcing half duplex mode of operation on the Serial Port. While sending data out of the serial port all received data are ignored. This mode of operation is available only on ports that operate …	Enumerationr/w Enumerated Values: 1 on 2 off 3 notApplicable	.1.3.6.1.4.1.15004.4.6.1.1.1.5
rcSerialTurnAround The amount of delay between the transmission of individual messages out of the serial port. For 'rcSerialProtocol' object value modbusServer(3) this value must be non-zero. It represents delay between se…	millisecondsInteger32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.15004.4.6.1.1.1.6
rcSerialPostTxDelay The number of bits needed to generate required delay with configured baudrate('rs232PortOutSpeed') after the last bit of the packet was sent out before serial UART starts listening to the RX line . This …	bitsInteger32r/w Constraints: range: 0-15	.1.3.6.1.4.1.15004.4.6.1.1.1.7
rcSerialHoldTime The maximum amount of time in ms that serial packet can be held in the queue before being sent to the serial line. Time is measured from the moment the packet is received from the IP layer.	millisecondsInteger32r/w Constraints: range: 0-15000	.1.3.6.1.4.1.15004.4.6.1.1.1.8
rcSerialDscp The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only.	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.15004.4.6.1.1.1.9
rcSerialRxtoTxDelay The minimum amount of time in ms that the transmission of a new message should delay after the last message is received through the serial port. This parameter is useful, especially for the half duplex …	millisecondsInteger32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.15004.4.6.1.1.1.10

This table provides configuration options for the ports when 
'rcSerialProtocol'equals modbusServer(3).

rcMbServerEntry row .1.3.6.1.4.1.15004.4.6.2.1.1

List of all the configuration options for a port for which
'rcSerialProtocol' equals modbusServer(3).

Indexes

rcMbServerPort

Column	Syntax	OID
rcMbServerPort The physical Serial Port Number for which this Entry contains the Modbus Server Protocol configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.2.1.1.1
rcMbServerRespTimer The allowable time to wait for the RTU to start to respond.	millisecondsInteger32r/w Constraints: range: 50-10000	.1.3.6.1.4.1.15004.4.6.2.1.1.2
rcMbServerAuxTcpPort The alternative TCP port number where a 'rcMbServerPort' may listen to incoming TCP conncetions. Note:TCP Modbus Server always listens on TCP port 502. So this parameter allows the RuggedCom serial devi…	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.2.1.1.3
rcMbServerSendExcep Allows the RuggedCom Serial Devices to enable or disable sending TCP Modbus exception back to the master if response has not been received from the RTU within expected time.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.2.1.1.4
rcMbServerLinkStats Enables links statistics collection.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.2.1.1.5

This table represents the entries for ports configured for Raw Socket
serial protocol on RuggedCom serial devices.

rcRawSockEntry row .1.3.6.1.4.1.15004.4.6.4.1.1

List of all the configuration options available for a port configured
for Raw Socket serial protocol on Ruggedcom serial devices.

Indexes

rcRawSockPort

Column	Syntax	OID
rcRawSockPort The physical Serial Port Number for which this Entry contains the Raw Socket serial protocol configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.4.1.1.1
rcRawSockPackChar The character that can be used to force forwarding of accumulated data to the network. If a packetization character is not configured - object is set to the value of '256', accumulated data will be forw…	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.15004.4.6.4.1.1.2
rcRawSockPackTimer The delay in ms from the last received character until when data is forwarded.	millisecondsInteger32r/w Constraints: range: 3-1000	.1.3.6.1.4.1.15004.4.6.4.1.1.3
rcRawSockPackSize The maximum number of bytes received from serial port to be forwarded.	bytesInteger32r/w Constraints: range: 64-1401	.1.3.6.1.4.1.15004.4.6.4.1.1.4
rcRawSockFlowControl The type of FlowControl to be used on the port.	RcFlowControlr/w Type Values: 1 none 2 xonXoff	.1.3.6.1.4.1.15004.4.6.4.1.1.5
rcRawSockTransport A transport protocol used for IP traffic for protocol on this port.	RcTransportr/w Type Values: 1 udp 2 tcp	.1.3.6.1.4.1.15004.4.6.4.1.1.6
rcRawSockCallDir Defines following: - whether to accept an incoming connection 'in(0)' or - to place an outgoing connection 'out(1)' or - to place an outgoing connection and wait for incomming 'both(2)' Note: This pa…	RcCallDirr/w Type Values: 0 in 1 out 2 both	.1.3.6.1.4.1.15004.4.6.4.1.1.7
rcRawSockMaxConn The maximum number of allowed incoming TCP connections.	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.15004.4.6.4.1.1.8
rcRawSockLocPort The local IP port to listen to an incoming TCP connection or UDP datagrams.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.4.1.1.9
rcRawSockRemPort The remote IP port to use when placing an outgoing connection.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.4.1.1.10
rcRawSockIpAdd Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicate with. - For incoming TCP connection (server), 'rcRawSoc…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.15004.4.6.4.1.1.11
rcRawSockLinkStats Enables links statistics collection for RawSocket on this port.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.4.1.1.12

This Table defines the configuration options available for ports 
configured for PreEmptive Raw Socket serial protocol.

rcPreemptRSEntry row .1.3.6.1.4.1.15004.4.6.5.1.1

A list of port entries with configuration options for ports configured
for PreEmptive Raw Socket protocol.

Indexes

rcPreemptRSPort

Column	Syntax	OID
rcPreemptRSPort The physical Serial Port Number for which this Entry contains the Preemptive Raw Socket serial protocol configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.5.1.1.1
rcPreemptRSPackChar The character that can be used to force forwarding of accumulated data to the network. If a packetization character is not configured - object is set to the value of '256', accumulated data will be forw…	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.15004.4.6.5.1.1.2
rcPreemptRSPackTimer The delay in milliseconds from the last received character until when data is forwarded.	millisecondsInteger32r/w Constraints: range: 3-1000	.1.3.6.1.4.1.15004.4.6.5.1.1.3
rcPreemptRSPackSize The Maximum number of bytes received from serial port to be packed in one IP packet.	bytesInteger32r/w Constraints: range: 64-1400	.1.3.6.1.4.1.15004.4.6.5.1.1.4
rcPreemptRSFlowControl The type of FlowControl to be used on the port.	RcFlowControlr/w Type Values: 1 none 2 xonXoff	.1.3.6.1.4.1.15004.4.6.5.1.1.5
rcPreemptRSLocPort The local IP port to listen to an incoming TCP connection or UDP datagrams.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.5.1.1.6
rcPreemptRSRemPort The remote TCP port to use when placing an outgoing connection.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.5.1.1.7
rcPreemptRSIpAdd Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicate with. - For incoming TCP connection (server), 'rcRawSoc…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.15004.4.6.5.1.1.8
rcPreemptRSLinkStats Enables links statistics collection.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.5.1.1.9
rcPreemptRSDynPackChar The character that can be used to force forwarding of accumulated data to the network for connection to dynamic master. If a packetization character is not configured, accumulated data will be forwarde…	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.15004.4.6.5.1.1.10
rcPreemptRSDynPackTimer The delay in milliseconds from the last received character until when data is forwarded to the dynamic master.	millisecondsInteger32r/w Constraints: range: 3-1000	.1.3.6.1.4.1.15004.4.6.5.1.1.11
rcPreemptRSDynTimeout The time in seconds that is allowed to dynamic master to be idle before it's connection is closed. The protocol listens to the socket open to dymamic master, and if no data are received within this time, conneciton w…	secondsInteger32r/w Constraints: range: 10-3600	.1.3.6.1.4.1.15004.4.6.5.1.1.12

This table represents the set of parameters provide the ability to 
configure DNP over RawSocket protocol settings for serial ports. 
If no ports appear, then the DNP over RawSocket protocol must first be 
assigned to port(s)

rcDnpRsEntry row .1.3.6.1.4.1.15004.4.6.9.1.1

List of ports with configuration parameters for DNP over RawSocket
serial protocol .

Indexes

rcDnpRsPort

Column	Syntax	OID
rcDnpRsPort The physical Serial Port Number for which this Entry contains DNP over Raw Socket serial protocol configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.9.1.1.1
rcDnpRsCalllDir Defines following: - whether to accept an incoming connection 'in(0)' or - to place an outgoing connection 'out(1)' or - to place an outgoing connection and wait for incomming 'both(2)' Note: This pa…	RcCallDirr/w Type Values: 0 in 1 out 2 both	.1.3.6.1.4.1.15004.4.6.9.1.1.2
rcDnpRsTransport A transport protocol used for IP traffic for DNPRS on this port.	RcTransportr/w Type Values: 1 udp 2 tcp	.1.3.6.1.4.1.15004.4.6.9.1.1.3
rcDnpRsMaxConns The maximum number of allowed incoming TCP connections.	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.15004.4.6.9.1.1.4
rcDnpRsLocPort The local IP port to listen to an incoming TCP connection or UDP datagrams.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.9.1.1.5
rcDnpRsRemPort The remote TCP port to use when placing an outgoing connection.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.9.1.1.6
rcDnpRsIpAdd Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicate with. - For incoming TCP connection (server), 'rcRawSoc…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.15004.4.6.9.1.1.7
rcDnpRsLinkStats Enables links statistics collection.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.9.1.1.8

This table presents the list of ports with configuration options for 
configuring the Mirrirod Bits serial protocol on RuggedCom serial 
devices

rcMirrBitsEntry row .1.3.6.1.4.1.15004.4.6.10.1.1

List of configuration options for all the ports configured for
Mirrored Bits serial protocol.

Indexes

rcMirrBitsPort

Column	Syntax	OID
rcMirrBitsPort The physical Serial Port Number for which this Entry contains the Mirrored Bits serial protocol configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.10.1.1.1
rcMirrBitsTransport A transport protocol used for IP traffic for MorroredBits on this port. This object is always set to the value of 'udp(2)'.	RcTransportr/w Type Values: 1 udp 2 tcp	.1.3.6.1.4.1.15004.4.6.10.1.1.2
rcMirrBitsLocPort The local IP port to listen to UDP datagrams.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.10.1.1.3
rcMirrBitsRemPort The Remote port to which protocol on this port can exchange UDP datagrams.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.10.1.1.4
rcMirrBitsIpAdd The IP Address of interface to listen to UDP datagrams.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.15004.4.6.10.1.1.5
rcMirrBitsLinkStats Enables links statistics collection.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.10.1.1.6

This table provides a list of port entries configured for TelnetPort 
Comport  serial protocolwith configuration options.

rcTelnetComportEntry row .1.3.6.1.4.1.15004.4.6.11.1.1

List of ports with configuration options for TelnetPortComports serial
protocol.

Indexes

rcTelnetComportPort

Column	Syntax	OID
rcTelnetComportPort Thephysical Serial Port Number for which this Entry contains the TelnetPortComport serial protocol configuration settings.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.15004.4.6.11.1.1.1
rcTelnetComportPackChar The character that can be used to force forwarding of accumulated data to the network. If a packetization character is not configured - object is set to the value of '256', accumulated data will be forw…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.15004.4.6.11.1.1.2
rcTelnetComportPackTimer The delay from the last received character until when data is forwarded.	millisecondsInteger32r/w Constraints: range: 3-1000	.1.3.6.1.4.1.15004.4.6.11.1.1.3
rcTelnetComportPackSize The maximum number of bytes received from serial port to be packed in one IP packet.	bytesInteger32r/w Constraints: range: 64-1400	.1.3.6.1.4.1.15004.4.6.11.1.1.4
rcTelnetComportFlowControl The type of FlowControl to be used on the port.	RcFlowControlr/w Type Values: 1 none 2 xonXoff	.1.3.6.1.4.1.15004.4.6.11.1.1.5
rcTelnetComportCallDir Defines following: - whether to accept an incoming connection 'in(0)' or - to place an outgoing connection 'out(1)' or - to place an outgoing connection and wait for incomming 'both(2)'. This protocol…	RcCallDirr/w Type Values: 0 in 1 out 2 both	.1.3.6.1.4.1.15004.4.6.11.1.1.6
rcTelnetComportLocPort The local IP port to listen to an incoming TCP connection.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.11.1.1.7
rcTelnetComportRemPort The remote TCP port to use when placing an outgoing connection.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.11.1.1.8
rcTelnetComportIpAdd Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicate with. - For incoming TCP connection (server), 'rcRawSoc…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.15004.4.6.11.1.1.9
rcTelnetComportLinkStats Enables links statistics collection.	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.15004.4.6.11.1.1.10

This table provides the statictics information for all active TCP 
connections on the RuggedCom serial device.

rcConnStatsEntry row .1.3.6.1.4.1.15004.4.6.15.1.1

List of parameters providing the statictics information for all active TCP
connections on the RuggedCom serial device.

Indexes

rcConnStatsRemIp rcConnStatsRemPort rcConnStatsLocPort

Column	Syntax	OID
rcConnStatsRemIp The remote IP address of the TCP connection.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.15004.4.6.15.1.1.1
rcConnStatsRemPort The remote port number of the connection.	Integer32 Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.15.1.1.2
rcConnStatsLocPort The local port number of the connection.	Integer32 Constraints: range: 1024-65535	.1.3.6.1.4.1.15004.4.6.15.1.1.3
rcConnStatsRxPkts The number of received packets.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.15004.4.6.15.1.1.4
rcConnStatsTxPkts The number of transmitted packets.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.15004.4.6.15.1.1.5