RUBYTECH-FGS2528KX-MIB Table View

The index of the ntp entry.

Default: 0,
0 : IPv4,
1 : IPv6.

Get/Set the NTP Time Server1. You can use the IP address or domain name.

0: Empty
1: Active
2: Edit
3: Delete

default:1
User privilege level range : 1 - 15

1: active
2: notInservice
3: edit
4: destroy
5: undo

The index of the trap host entry.

The version of the Trap PDU. Version : 2(SNMPv2c), 3(SNMPv3)

Server IP Type. Default: 4,
4 : IPv4,
6 : IPv6.

This is the IP of the trap host.

This is the receiving-port number of the trap host.
range : 1 - 65535.

The community/security name for the trap PDU.

The Severity Level.
0 : Emerg, 1 : Alert, 2 : Crit, 3 : Error, 4 : Warning, 5 : Notice, 6 : Info, 7 : Debug.

The Security Level, NoAuthNoPriv, AuthNoPriv, and AuthPriv.
1 : NoAuthNoPriv, 2 : AuthNoPriv, 3 : AuthPriv.
Privacy protocol will be configured as 'DES' automatically if security level is 3(AuthPriv).

Authentication Protocol, there are SHA and MD5 supported presently.
1 : MD5, 2 : SHA.

Authentication Password, is used for authenticating. The return value is always '********'.
If the authentication protocol is MD5, the length of password should be 8 ~ 32 characters.
If the authentication protocol is SH…

This is the Privacy Protocol, which is used in AuthPriv. Only supports DES.
An empty string will be returned if the security level is not 3(AuthPriv).
1 : DES.

The password is Privacy Key. The return value is always '********'. This Key
must be more than 8 characters, and less than 32 characters.

0:Empty, 1:Active mode, 2:Edit mode, 3:Delete.

port, range : 1 - port number.

Show port media.

The current link state.

The current link speed of the port.

default: 1,
0: disable state,
1: auto,
2: 10 Half,
3: 10 Full,
4: 100 Half,
5: 100 Full,
6: 1G full,
only 'Dual Media' port have 7-11 option.
Dual Media port default: 7,
7: SFP_Auto_AMS,
8: 100FX_AMS,
9: 100…

0: disable
1: enable
2: not support.

0: disable
1: enable
2: not support.

default: 0,
0: disable
1: enable
2: not support.

default: 9600 , range : 1518 - 9600

default: 0,
Excessive Collision Mode :
0: Discard,
1: Restart,
2: not support.

default: 0,
PowerControl :
0: disable,
1: Actiphy,
2: Dynamic (perfectReach),
3: Enable,
4: not support.

Interface specific description.
Up to 47 characters describing this interface.

default: 200, range : 200 - 1000

default: 600 , range : 600 - 3000

default: 10000, range : 10000 - 50000

default: 1
1: GVRP

default: 1
1: VLAN

default: 0
0: normal-participant
1: non-participant

port, range : 1 - port number.

Peer MAC is MAC address of the neighbour Switch from with GARP frame is received.

explain Failed count here.

default: 0
1: enable
0: disable

default: 0
1: enable
0: disable

default: 0, range : 0 - 3

default: 0
0: disable
1: enable
2: rx only
3: tx only
Setting Tx mirroring for analyzer port has no effect. Tx mirroring ignored

default: 0, range : 0 - 255

default: 1,
0: Deny
1: Permit

default: 0,
0: Disable
range : 0 - 16

default: 0
0: Disable
range : 0 - end port number

default: 0
0: Disable
1: Enable

default: 0
0: Disable
1: Enable

default: 1
0: Disable
1: Enable

Counts the number of frames that match this ACE.

Rate Limiter ID.
range : 1-16

default: 1,
range : <0-3276700> pps

If the ACE ID is specified and an entry with this ACE ID
already exists, the ACE will be modified. Otherwise, a
new ACE will be added.
range : 1 - 256.

If the next ACE ID is non zero, the ACE will be placed
before this ACE in the list. If the next ACE ID is zero,
the ACE will be placed last in the list.
range : 0 - 256.

Indicates the ingress port of the ACE. Possible values are:
All: The ACE will match all ingress port.
Port: The ACE will match a specific ingress port.Format: 1,3,6.

policy value.
range : 0 - 255.

policy bitmask.
range : 0 - 255(0xff).

0: any,
1: arp,
2: etype,
3: icmp,
4: ipv4,
5: tcp,
6: udp.

default: 1,
0: Deny
1: Permit

Frames that hit the ACE are redirected to the port number specified here.
Disabled: indicates that the port redirect operation is disabled.
Port Format: 1,3,6.

default: 0,
0: disable - Frames matching the ACE are not logged.
1: enable - Frames matching the ACE are stored in the system log.

default: 0,
0: Disable
range : 0 - 16

default: 0,
0: disable - Port shut down is disabled for the AC.
1: enable - If a frame matches the ACE, the ingress port will be disabled.

Specify the tag priority for this ACE.
The tag priority can't be set when 802.1Q Tagged is disabled
default: 8,
8: Any,
range : 0 - 8

Specify the VLAN ID filter for this ACE.
The vid can't be set when 802.1Q Tagged is disabled.
default: 0,
0: Any - No VLAN ID filter is specified.
range : 0 - 4094

0: Any - Any but excluding 0x0800(IPv4) 0x0806(ARP) and 0x86DD(IPv6).
range : 0 or 1536(0x0600)- 65535(0xffff).

Configure source MAC address for this ACE.
<mac-address>: A frame that hits this ACE matches this source MAC address value.
Any: Don't care.

DMAC Type.
default: 0,
0: Any - Don't care.
1: Broadcast - Frame must be broadcast.
2: Unicast - Frame must be unicast.
3: Multicast - Frame must be multicast.
4: mac address
range : 0 - 4

Configure destination MAC address for this ACE.
<mac-address>: A frame that hits this ACE matches this destination MAC address value.
Any: Don't care.
Broadcast: Frame must be broadcast.
Unicast: Frame must…

Configure ARP opcode for this ACE.
default: 0,
0: Any - Don't care.
1: arp.
2: rarp.
3: other.
4: No data.
range : 0 - 3

Specify the available ARP/RARP opcode (OP) flag for this ACE.
default: 2,
0: Frame must have ARP Reply or RARP Reply OP flag.
1: Frame must have ARP Request or RARP Request OP flag set.
2: Any - Don't care.
3: No data.
…

Specify whether frames can hit the action according to their sender hardware address field (SHA) settings.
default: 2,
0: ARP frames where SHA is not equal to the SMAC address.
1: ARP frames where SHA is equal to the SM…

Specify whether frames can hit the action according to their target hardware address field (THA) settings.
default: 2,
0: RARP frames where THA is not equal to the DMAC address.
1: RARP frames where THA is equal to the …

Specify whether frames can hit the action according to their ARP/RARP hardware address length (HLN) and
protocol address length (PLN) settings.
default: 2,
0: ARP/RARP frames where the HLN is not equal to Ethernet(0x06)…

Specify whether frames can hit the action according to their ARP/RARP hardware address space (HRD) settings.
default: 2,
0: ARP/RARP frames where the HLD is not equal to Ethernet(1).
1: ARP/RARP frames where the HLD is …

Specify whether frames can hit the action according to their ARP/RARP protocol address space (PRO) settings.
default: 2,
0: ARP/RARP frames where the PRO is not equal to IP\n(0x800).
1: ARP/RARP frames where the PRO is …

Configure source IP address for this ACE.
default: 0,
0: Any - Don't care.
1: IP Address.
2: No data.
range : 0 - 1

A frame that hits this ACE matches this source IP address value.

Network prefix.
default: 32,
0: No data.
range : 1 - 32

Configure destination IP address for this ACE.
default: 0,
0: Any - Don't care.
1: IP Address.
2: No data.
range : 0 - 1

A frame that hits this ACE matches this destination IP address value.

Network prefix.
default: 32,
0: No data.
range : 1 - 32

Configure IP protocol for this ACE.
default: 256,
256: Any - Don't care.
257: No data.
range : 0 - 256

Configure IP Time-to-Live flags for this ACE.
default: 2,
0: IPv4 frames with a Time-to-Live field is equal to zero.
1: IPv4 frames with a Time-to-Live field greater than zero.
2: Any - Don't care.
3: No data.
range : 0…

Configure IP options flag for this ACE.
default: 2,
0: IPv4 frames where the options flag is unset.
1: IPv4 frames where the options flag is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

Configure IP fragment offset flags for this ACE.
default: 2,
0: IPv4 frames where the MF bit is unset and the FRAG OFFSET field is equal zero.
1: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater t…

Configure ICMP type for this ACE.
default: 256,
256: Any - Don't care.
257: No data.
range : 0 - 256

Configure ICMP code for this ACE.
default: 256,
256: Any - Don't care.
257: No data.
range : 0 - 256

Configure Source UDP/TCP port range for this ACE.
default: 0,
65536: No data.
range : 0 - 65535

Configure Source UDP/TCP port range for this ACE.
default: 0,
65536: No data.
range : 0 - 65535

Configure Destination UDP/TCP port range for this ACE.
default: 0,
65536: No data.
range : 0 - 65535

Configure Destination UDP/TCP port range for this ACE.
default: 0,
65536: No data.
range : 0 - 65535

Configure TCP (FIN) flags for this ACE.
default: 2,
0: TCP frames where the FIN field is unset.
1: TCP frames where the FIN field is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

Configure TCP (SYN) flags for this ACE.
default: 2,
0: TCP frames where the SYN field is unset.
1: TCP frames where the SYN field is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

Configure TCP (RST) flags for this ACE.
default: 2,
0: TCP frames where the RST field is unset.
1: TCP frames where the RST field is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

Configure TCP (PSH) flags for this ACE.
default: 2,
0: TCP frames where the PSH field is unset.
1: TCP frames where the PSH field is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

Configure TCP (ACK) flags for this ACE.
default: 2,
0: TCP frames where the ACK field is unset.
1: TCP frames where the ACK field is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

Configure TCP (URG) flags for this ACE.
default: 2,
0: TCP frames where the URG field is unset.
1: TCP frames where the URG field is set.
2: Any - Don't care.
3: No data.
range : 0 - 2

1: active
2: notInservice
4: destroy
5: undo

Indicates the ACL user.
S : Static.
IPMG : IP Management.
IPSG : IP Source Guard.
IPMC : IPMC.
ARPI : Arp Inspection.
UPnP : UPnP.
DHCP : DHCP.

ACE ID.
range : 1 - 256.

Indicates the ingress port of the ACE. Possible values are:
All: The ACE will match all ingress port.
Port: The ACE will match a specific ingress port.

Indicates the frame type of the ACE.

Indicates the forwarding action of the ACE.

Indicates the rate limiter number of the ACE.

Indicates the port redirect operation of the ACE. Frames matching the ACE are redirected to the port number.

Specify the mirror operation of this port.

Forward packet that matched the specific ACE to CPU.

The counter indicates the number of times the ACE was hit by a frame.

Indicates the hardware status of the specific ACE. The specific ACE is not applied to the hardware due to hardware limitations.

Protection group ID.
range : 1 - 64.

East port of the switch in the ring.
range : 1 - 26.

West port of the switch in the Ring.
As interconnected sub-ring will have only one ring port, W port is configured as 0 for interconnected sub-ring.
0: in this field indicates that no west port is associated with this…

The East Signal Fail reporting MEP.
range : 1 - 32.

The West Signal Fail reporting MEP. As only one SF MEP is associated with interconnected sub-ring without virtual channel,
it is configured as 0 for such ring instances. 0: in this field indicates that no west SF MEP is…

The East APS PDU handling MEP.
range : 1 - 32.

The West APS PDU handling MEP. As only one APS MEP is associated with interconnected sub-ring without virtual channel,
it is configured as 0 for such ring instances. 0: in this field indicates that no west APS MEP is as…

Type of Protectiong ring. It can be either major ring or sub-ring.
default: 0,
0: Major
1: Sub

Interconnected Node indicates that the ring instance is interconnected.
default: 0,
0: No - indicates that the configured instance is not interconnected.
1: Yes - indicates it is an interconnected node for this insta…

Sub-rings can either have virtual channel or not on the interconnected node.
default: 0,
0: No - indicates, sub-ring doesn't have virtual channel.
1: Yes - indicates it is a sub-ring with virtual channel.

Major ring group ID for the interconnected sub-ring.
It is used to send topology change updates on major ring.
If ring is major, this value is same as the protection group ID of this ring.

There is an active alarm on the ERPS.

Down: This ERPS is only created and has not yet been configured - is not active.
Up: This ERPS is configured - is active.

Guard timeout value to be used to prevent ring nodes from receiving outdated R-APS messages.
default : 500(ms).
range : 10 - 2000(ms).

The Wait To Restore timing value to be used in revertive switching.
default : 5(minutes).
range : 1 - 12(minutes).

The timing value to be used to make persistent check on Signal Fail before switching.
default : 0(seconds).
range : 0 - 10000(ms).

ERPS version of a group.
default : 1.
0: v1
1: v2

ERPS revertibility of a group.
default : 1.
0: non-revertible
1: revertible

VID of the protected vlan.

1: active
2: notInservice
3: edit
4: destroy
5: undo

default: 0
0:disable
1:enable

default: 99
0~2: Max Dynamic clients
99:Unlimited

Port, range: 1 - port number.

VLAN ID, range: 1 - 4094.

IP address allowed for doing IP source guard.

Allowed Source MAC address, format 0a 1b 2c 3d 4e 5f

1: active
2: notInservice
3: edit
4: destroy
5: undo

default: 0
0: disable
1: enable

Port, range: 1 - port number.

VLAN ID, range: 1 - 4094.

IP address allowed for doing ARP request.

Allowed Source MAC address in ARP request packets, format 0a 1b 2c 3d 4e 5f

1: active
2: notInservice
3: edit
4: destroy
5: undo

default: 1
0: trust port mode
1: untrust port mode

default: 0
0: none
1: clear